Table of Contents
Related Manuals for Sears 200.71440
Summary of Contents for Sears 200.71440
- Page 1 OWNER’S MANUAL Model No. 200.71440 40/2 AMP MANUAL BATTERY CHARGER 200 AMP CAUTION: ENGINE STARTER Read and Follow All Safety Rules and Operating Instructions Before Every Use of this Product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
-
Page 2: Table Of Contents
Please read this Owner's Manual before using your Battery Charger The Sears model 200.71440, Manual Battery Charger/Engine Starter, offers a wide range of features to accommodate the needs for home or commercial use. This manual will show you how to use your charger safely and effectively. -
Page 3: Important Safety Instructions
If this occurs, flush eyes immediately with running cold water for at least 10 minutes. Then immediately get medical attention. Sears 440 - Sch 516 9/16/95 – SAVE THESE INSTRUCTIONS – To reduce the risk of explosion, explosive gases, or injury while using your battery charger, follow the precautions listed below: •Do not disassemble charger. -
Page 4: Parts
Parts This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Replacement Parts List Sears 71440 Item Description Handle Negative (BLK) cable w/clamps Positive (RED) cable w/clamps... -
Page 5: Before Using Your Battery Charger
Be sure to tap the hub on straight. Slide both wheels onto the axle with the hubs facing inward. Sears 440 - Sch 516 9/16/95 continued on next page... -
Page 6: Plugging It In
120 volt circuit. The plug must be plugged into an outlet that has been properly installed and grounded in accordance with all local codes and ordinances. Sears 440 - Sch 516 9/16/95... -
Page 7: Using An Extension Cord
Sears 440 - Sch 516 9/16/95 • Wear safety glasses. See additional "Personal Safety Precautions" on page 2. • Be sure that the area around the battery is well ventilated while it is being charged. -
Page 8: Using Your Battery Charger
Battery Charger To obtain the best results from your battery charger, you must know how to use it properly. This section will tell you how to set the controls. And how you can charge a battery while it is still in the vehicle, or you can remove it and then charge it. -
Page 9: Charging Your Battery
OFF position. 12. Standing away from the battery, remove the charger clamp from the chassis first, then from the battery post or terminal. 13. Clean and store the battery charger in a dry location. Sears 440 - Sch 516 9/16/95... - Page 10 11. Standing away from the battery, remove the charger leads. Remove the NEGATIVE clamp first, then from the POSITIVE battery post or terminal. 12. Clean and store the battery charger in a dry location. Sears 440 - Sch 516 9/16/95...
-
Page 11: Calculating Charge Time
To convert Reserve Capacity to Amp Hours, divide Reserve Capacity by 2, and add 16: Amp Hours = Reserve Capacity + 16 Sears 440 - Sch 516 9/16/95 • Marine, or deep-cycle batteries are usually rated in Reserve Capacity (RC). -
Page 12: Using The Engine Start Feature
3. Occasional cleaning of the case with a soft cloth will keep the finish shiny and help prevent corro- sion. Sears 440 - Sch 516 9/16/95 6. If the engine still does not start, charge the battery for five more minutes in the 40 amp position before cranking it again for five seconds. -
Page 13: Troubleshooting
Circuit breaker cycles when current draw is too high. Separate the clamps. Check for worn cables and replace if needed. Have a Sears technician test the battery. Correct connections. Correct Volt/Amp Selector setting. Crank time varies with the amount of current drawn. If cranking draws more than 200 amps, crank time may be less than 5 seconds. - Page 14 For the repair or replacement parts you need Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For the location of a Sears Repair Service Center in your area Call 24 hours a day, 7 days a week 1-800-488-1222...