Advertisement
A. Quick Set-Up Method
STEP1 Turn on the component you want to pro-
gram. To program your TV, turn on the TV.
STEP2 Point the remote control at the compo-
nent.
STEP3 Press and hold the [DEVICE] key for 5
seconds until the Device LED will blink
once and stays on. Continue to hold the
[DEVICE] key and press the number key
assigned to your brand in the Quick
Set-up Code Table. The component
should turn off as soon as the number
key is pressed. (If it does not turn off,
release the [DEVICE] key and use the
Pre-Programmed 3-Digit code Method
or Scanning Method.)
STEP4 Release the [DEVICE] key to save the
code. The Device LED will blink twice to
confirm that the code is stored.
Repeat the steps above for all components
(CBL, TV, AUD, DVD, AUX).
B. Quick Set-up Code Tables
CBL
Quick Number
Manufacturer/Brand
0
PACE DTA
1
SA/CISCO, SAMSUNG, PACE DIGITAL
2
MOTOROLA DIGITAL
3
MOTOROLA DTA
4
EVOLUTION DTA
5
CISCO IPTV
6
ADB IPTV
7
TECHNICOLOR
8
AMINO 140/540 IPTV
9
MOTOROLA IPTV
TV
Quick Number
Manufacturer/Brand
0
SANYO
1
SONY
2
SAMSUNG
3
LG
4
TOSHIBA
5
PANASONIC
6
PHILIPS
7
HITACHI
8
SHARP
9
VIZIO
AUDIO
Quick Number
Manufacturer/Brand
0
ROTEL
1
DENON
2
YAMAHA
3
MARANTZ
4
SONY
5
INTEGRA
6
HARMAN KARDON
7
PIONEER
8
ONKYO
9
LEXICON
DVD
Quick Number
Manufacturer/Brand
0
HITACHI
1
SONY
2
PHILIPS
3
SAMSUNG
4
PHILIPS MAGNAVOX
5
PANASONIC
6
LG
7
JVC
8
DENON
9
PIONEER
AUX
Quick Number
Manufacturer/Brand
0
BOSE
1
HP
2
APPLE / iPod
3
APPLE / iPod
4
MICROSOFT / XBOX
5
SONY / PS2
6
LUTRON
7
X-10
8
X-10
9
MICROSOFT / XBOX
C. Pre-Programmed 3-Dight Code Method
STEP1 Turn on the equipment that you want
the remote control to operate (Cable
Box, TV, DVD, etc.).
STEP2 Press the [DEVICE] button and the
[OK/SEL] button simultaneously for three
seconds. The corresponding device LED
will turn on indicating that it is ready to
be programmed. The LED will remain on
for 30 seconds. The next step must be
entered while the LED is on.
STEP3 Point the remote control toward the
equipment and enter the three-digit
code number assigned to your brand
from the code tables. If there are more
than one three-digit number listed for
your brand, try one code number at a
time until your equipment turns off.
*Note : You can verify that you have selected the
correct code by pressing the [POWER]
button. The equipment should turn back
on. Then try all of the functions on the
remote control (i.e. volume, mute, etc.) to
ensure you have the correct code. If any
of the functions do not operate as they
should, repeat the instructions from
STEP 3 above using the next three digit
code number from the brand list.
STEP4 Store the three-digit code by pressing the
same [DEVICE] button once again. The
device LED will blink twice to confirm that
the code has been stored.
D. Auto-Search Method
If none of the three digit code numbers assigned to
your brand of equipment works, or the code table
does not list your brand, you can use the Auto
Search Method to find the correct three-digit code
number for your equipment by following steps:
STEP1 Turn on the equipment that you want
the remote control to operate (Cable
Box, TV, DVD, etc.).
STEP2 Press the [DEVICE] button and the
[OK/SEL] button simultaneously for
three seconds. The device LED will turn
on indicating that it is ready to be
programmed. The LED will remain on
for 30 seconds. The next step must be
entered while the LED is on.
STEP3 Press the [CH5] or [CH6] button one at
a time or keep it pressed. The remote
will emit a series of Power ON/OFF
code signals. Release the [CH5] or [CH6]
button as soon as the equipment turns off.
*Note : You can verify that you have selected the
correct code by pressing the [POWER]
button. The equipment should turn back
on. Then try all of the functions on the
remote control (i.e. volume, mute, etc.) to
ensure you have the correct code. If any of
the functions do not operate as they should,
repeat the instructions from STEP 3 above
to continue the Auto Search Method.
STEP4 Press the same [DEVICE] button to store
the code. The Device LED will blink twice
to confirm that the code has been stored.
E. The Learning Method
STEP1 Press the [DEVICE] button (TV,AUD, DVD,
or AUX) to be programmed and the
[ASPECT] buttons simultaneously for 3
seconds until the Device LED light turns on.
STEP2 Point the PHAZR-5 at the other remote,
head-to-head, 1 or 2 inches apart.
STEP3 Press the button on the PHAZR-5 that
you want to teach a command to. For
example, press the [MUTE] button to
learn a command to the [MUTE] button.
STEP4 Press and hold the button on the other
remote that corresponds to the command
you want to teach until the PHAZR-5
Device LED light blinks twice.
*Note : The LED will blink 5 times if there
was an error in the learning process.
Repeat STEPS 3 and 4 if this occurs.
Continue learning other buttons by
repeating STEPS 3 and 4.
STEP5 Once you have completed teaching the
PHAZR-5 all desired commands for the
component, save the learned commands
by pressing the [DEVICE] and [ASPECT]
buttons simultaneously until the Device
LED blinks 3 times. Now test all of the
buttons to make sure they operate correctly.
F. Erasing a Single Learned Command
STEP1 Press the [DEVICE] and [ASPECT] buttons
simultaneously for 3 seconds until the
Device LED light turns on.
STEP2 Press and hold the button you want to
erase for 3 seconds. The Device LED
will blink twice to confirm the erasure.
STEP3 To exit, press and hold both the [DEVICE]
and [ASPECT] buttons simultaneously
until the Device LED blinks 3 times.
G. Erasing All Learned Commands
from One Device
STEP1 Press the [DEVICE] and [ASPECT] buttons
simultaneously for 3 seconds until the
Device LED light turns on.
STEP2 Press and hold both the [DEVICE] button
you want to erase and the [PAUSE] button
for 5 seconds. The Device LED will blink
twice to confirm the erasure.
STEP3 To exit, press and hold both the [DEVICE]
and [ASPECT] buttons simultaneously
H.To Identify the 3-Digit Code
Programmed for a Device
STEP1 Press the appropriate [DEVICE] button
and the [OK/SEL] button simultaneously
for three seconds. The device LED will
turn on for 30 seconds. The next step
must be performed while the LED is on.
STEP2 Press the [INFO] button. The device LED
will blink a number of times indicating
the number of each digit for the code.
Each digit is separated by a one second
interval of the LED being off.
Example :One blink, (pause) three blinks,
(pause) eight blinks indicates the
code number 138.
*Note : Ten blinks indicates the number 0.
I. Programming the AUX Device
You can take advantage of the AUX function to
program a devices such as a media PC, gaming
console or satellite radio receiver. Follow the
instruction in section C to program an AUX
device. You can also program the AUX button for
a second TV, DVD or Audio Device. To do this
follow the instructions below.
STEP1 Turn on the 5th device you want to
program (TV, AUD, DVD, etc.).
STEP2 Press the [AUX] button and the
[OK/SEL] button simultaneously for 3
seconds. The [AUX] device LED will
turn on for 30 seconds.
STEP3 Press the [Device] button For the type of
device you want to setup. Point the remote
control toward the device and enter the
3-digit code number assigned to your brand.
*Note : To program a second TV press TV, etc.
STEP4 When the equipment turns off verify
that you have selected the correct
code by pressing the [POWER] button.
The equipment should turn back on.
Then try all of the functions on the
remote control (i.e. volume, mute, etc.)
to ensure you have the correct code.
If any of the functions do not operate as
they should, enter the next 3-digit code
number from the brand list.
STEP5 Once you have found the correct 3-digit
code, save it by pressing the [AUX] button
one more time. The [AUX] LED light will
blink twice to confirm the code was stored.
J
T
b
c
S
S
S
S
K
V
to
D
If
m
S
S
S
*
L
If
m
S
S
S
Advertisement
