Download Print this page

Universal Remote Control PHAZR-5 UR5U-9000 Operating Instructions

Cable remote control

Advertisement

Operating Instructions For
1
4
Introduction
Button Functions
PHAZR-5
The PHAZR-5 UR5U-9000 & UR5U-9020 is
designed to operate the CISCO / SA,
Pioneer, Pace Micro, Samsung and
Motorola digital set tops, Plus the majority
Cable Remote Control
of TV, AUD, DVD and AUX equipment on
the market as shown below.
CBL : Cable Set-top Box
TV : Televisions
UR5U-9000 & UR5U-9020
AUD : Audio Receivers
DVD : DVD Players
AUX : Media PC, Gaming System, etc.
2
Replacing Batteries
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
5
Programming the Remote Control
3
Operations
IMPORTANT SETUP NOTE!
In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV,
AUD, DVD or AUX button, depending on what device you are programming the remote to operate.
DEFAULT STATE:
Device Default: Cable Set-Top Box (STB)
There are three ways you can program your remote:
* Quick Set-Up Method
Channel Default: CABLE channel and numbers
* The Pre-Programmed 3-Digit Code Method
through the CABLE STB. You have the option of
* The Auto-Search Method
controlling your CABLE channel and numbers
through the TV or AUD. Refer to section I for pro-
The Quick Set-Up Method is a unique feature that enables the fastest and easiest setup by using a 1 digit code.
gramming steps.
This is the quickest way to set up devices made by popular manufacturers.
The Pre-Programmed Code Method allows you to setup all of the buttons at once by entering 3-digit code
Volume Default: Volume and Mute control are
numbers that correspond with the components manufacturer/brand. Code tables for this method are on the
automatically transferred to the respective
backside of the operating instructions.
Component based on the Device selected:
The Auto-Search Method scans through all of the codes in the remote control, one at a time allowing you to
CBL:Cable Set-Top Box ; TV:TV ; AUD:AUD.
identify the correct code.
DVD:TV ; AUX:AUX. You have the option of
Universal Remote Control, Inc.
controlling CABLE Volume and Mute through
IMPORTANT SETUP NOTE!
www.universalremote.com
the TV, DVD or AUD. Refer to section H for
This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you do
OCE-0081C Rev 05 (02/01/13)
programming steps.
not press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.
A. Quick Set-Up Method
DVD
STEP4 Store the three-digit code by pressing
the same [DEVICE] button once again.
Quick Number
Manufacturer/Brand
STEP1 Turn on the component you want to
The device LED will blink twice to
program. To program your TV, turn on
0
HITACHI
confirm that the code has been
the TV.
1
SONY
stored.
2
PHILIPS
STEP2 Point the remote control at the compo-
3
SAMSUNG
nent.
4
PHILIPS MAGNAVOX
D. Auto-Search Method
STEP3 Press and hold the [DEVICE] key for 5
5
PANASONIC
If none of the three digit code numbers
seconds until the Device LED will blink
6
LG
assigned to your brand of equipment works, or
7
JVC
once and stays on. Continue to hold
the code table does not list your brand, you can
8
DENON
the [DEVICE] key and press the num-
use the Auto Search Method to find the correct
9
PIONEER
ber key assigned to your brand in the
three-digit code number for your equipment by
Quick Set-up Code Table. The compo-
following steps:
nent should turn off as soon as the
AUX
number key is pressed. (If it does not
STEP1 Turn on the equipment that you want
Quick Number
Manufacturer/Brand
the remote control to operate (Cable
turn off, release the [DEVICE] key and
0
BOSE
Box, TV, DVD, etc.).
use the Pre-Programmed 3-Digit code
1
HP
Method or Scanning Method.)
STEP2 Press the [DEVICE] button and the
2
APPLE / iPod
[OK/SEL] button simultaneously for
STEP4 Release the [DEVICE] key to save the
3
APPLE / iPod
three seconds. The device LED will
code. The Device LED will blink twice
4
MICROSOFT / XBOX
turn on indicating that it is ready to be
to confirm that the code is stored.
5
SONY / PS2
programmed. The LED will remain on
6
LUTRON
Repeat the steps above for all components (TV,
for 30 seconds. The next step must be
7
X-10
AUD, DVD, AUX).
8
X-10
entered while the LED is on.
9
MICROSOFT / XBOX
STEP3 Press the [CH5] or [CH6] button one
B. Quick Set-up Code Tables
at a time or keep it pressed. The
remote will emit a series of Power
C. Pre-Programmed 3-Dight Code Method
TV
ON/OFF code signals. Release the
[CH+] or [CH-] button as soon as the
Quick Number
Manufacturer/Brand
STEP1 Turn on the equipment that you want
equipment turns off.
0
SANYO
the remote control to operate (Cable
1
SONY
Box, TV, DVD, etc.).
*Note : You can verify that you have selected the
2
SAMSUNG
correct code by pressing the [POWER]
STEP2 Press the [DEVICE] button and the
3
LG
button. The equipment should turn back
[OK/SEL] button simultaneously for
4
TOSHIBA
on. Then try all of the functions on the
three seconds. The corresponding
5
PANASONIC
remote control (i.e. volume, mute, etc.) to
device LED will turn on indicating that
6
PHILIPS
ensure you have the correct code. If any of
it is ready to be programmed. The LED
7
HITACHI
the functions do not operate as they should,
will remain on for 30 seconds. The
8
SHARP
repeat the instructions from STEP 3 above
next step must be entered while the
9
VIZIO
to continue the Auto Search Method.
LED is on.
STEP4 Press the same [DEVICE] button to
STEP3 Point the remote control toward the
store the code. The Device LED will
equipment and enter the three-digit
blink twice to confirm that the code
code number assigned to your brand
AUDIO
has been stored.
from the code tables. If there are more
Quick Number
Manufacturer/Brand
than one three-digit number listed for
E. To Identify the 3-Digit Code
0
ROTEL
your brand, try one code number at a
Programmed for a Device
1
DENON
time until your equipment turns off.
2
YAMAHA
STEP1 Press the appropriate [DEVICE] button
3
MARANTZ
*Note : You can verify that you have selected the
and the [OK/SEL] button simultaneously
4
SONY
correct code by pressing the [POWER]
for three seconds. The device LED will
5
INTEGRA
button. The equipment should turn back
turn on for 30 seconds. The next step
6
HARMAN KARDON
on. Then try all of the functions on the
must be performed while the LED is on.
7
PIONEER
remote control (i.e. volume, mute, etc.)
STEP2 Press the [INFO] button. The device LED
8
ONKYO
to ensure you have the correct code. If
will blink a number of times indicating
9
LEXICON
any of the functions do not operate as
the number of each digit for the code.
they should, repeat the instructions from
Each digit is separated by a one second
STEP 3 above using the next three digit
interval of the LED being off.
code number from the brand list.
Example :One blink, (pause) three blinks,
and then press [POWER]. Repeat this for
J. Programming a 'Macro' button.
(pause) eight blinks indicates the
the other components you want to turn
If your remote model has custom-programmable
code number 138.
on/off with the [SYSTEM ON/OFF] button.
Macro buttons available(See Section 4), they
*Note : Ten blinks indicates the number 0.
STEP4 Press the [CH5] button to save the
can be programmed to act as a 'Macro' or
power commands you stored. The
Favorite Channel button in CABLE mode. This
[CBL] button will blink twice to confirm
allows you to program up to five 2-digit channels,
F. Programming the AUX Device
the commands have been saved.
four 3-digit channels or three 4-digit channels
that can be accessed with one button press.
You can take advantage of the AUX function to
program a devices such as a media PC, gaming
STEP1 Press the [CBL] button to select the CBL
H. Programming Volume Control
console or satellite radio receiver. Follow the
mode.
instruction in section C to program an AUX
Volume and Mute control are factory programmed
STEP2 Press the [MACRO] button and
device. You can also program the AUX button
to automatically transfer to the respective Device
[OK/SEL] button simultaneously for 3
for a second TV, DVD or Audio Device. To do
mode You select, as follows:
seconds. The [CBL] button will turn on
this follow the instructions below.
for 30 seconds.
CBL : CBL
T V : TV
AUD : AUD
STEP1 Turn on the 5th device you want to
DVD : TV
AUX : AUX
STEP3 Enter the the 2, 3 or 4-digit code for the
program (TV, AUD, DVD, etc.).
channel you want programmed first (for
If you wish to store the TV volume control in
STEP2 Press the [AUX] button and the
example, 007) using the Number Pad,
CBL mode, use the following steps.
[OK/SEL] button simultaneously for 3
then press the [STOP] button. Then
seconds. The [AUX] device LED will
STEP1 Press the [OK/SEL] button and [CBL]
enter the code for the next channel (for
turn on for 30 seconds.
button simultaneously for three
example, 050), then press the [STOP]
button. Repeat this process for the third
STEP3 Press the [Device] button For the type
seconds. The device LED will turn on
channel. The [CBL] button will blink
of device you want to setup. Point the
for 30 seconds. The next step must
once for each channel entered.
remote control toward the device and
be performed while the LED is on.
enter the 3-digit code number
STEP2 Press the [VOL5] button. The device
STEP4 Press the [CH5] button to store the
assigned to your brand.
LED will blink.
channels that were selected. The
[CBL] button will blink twice to confirm
*Note : To program a second TV press TV, etc.
STEP3 Press [TV] button. The device LED will
the storage of commands.
blink twice to confirm the programming.
STEP4 When the equipment turns off verify
To access the programmed channels, press
that you have selected the correct
*Note : To return CBL device to CBL volume
the [MACRO] button once. This will bring up
code by pressing the [POWER] button.
repeat steps above replacing [TV] with
the first channel. Press once again and it will
The equipment should turn back on.
[CBL] in Step 3.
bring up the second channel. Press again and
Then try all of the functions on the
it will bring up the third channel.
I. Programming Channel Control
remote control (i.e. volume, mute, etc.)
to ensure you have the correct code.
K. Low Battery Warning
You can program the channel controls (Channel
If any of the functions do not operate
Up, Channel Down, Last and Numbers) from
as they should, enter the next 3-digit
When the batteries are low and need to be
one Device to operate in another Device mode.
code number from the brand list.
replaced with fresh batteries, the Device LED
Default channel control settings on the remote
lights will blink 2 times in sequence whenever a
STEP5 Once you have found the correct
control are as follows:
[POWER] button is pressed to turn on equipment.
3-digit code, save it by pressing the
CBL : CBL
T V : CBL
AUD : AUD
[AUX] button one more time. The [AUX]
L. Memory Lock System
DVD : DVD
AUX : AUX
LED light will blink twice to confirm the
code was stored.
This remote control is designed to retain pro-
If you wish to store the TV channel controls in
grammed memory for 10 years even after batteries
TV mode, use the following steps.
are removed from the remote control.
STEP1 Press the [OK/SEL] button and [TV] button
G. Programming the System On/Off Button
simultaneously for three seconds. The
M. Record Your Component Set-up Codes
This allows you to program the System On/Off
device LED will turn on for 30 seconds.
TV
Set-up Code Number:
button so it can send up to five power On/Off
The next step must be performed while
commands with one button press.
the LED is on.
AUD Set-up Code Number:
STEP2 Press the [VOL6] button. The device
STEP1 Press the [CBL] button.
DVD
Set-up Code Number:
LED will blink.
STEP2 Press the [SYSTEM ON/OFF] button
AUX
Set-up Code Number:
STEP3 Press [TV] button. The device LED will
and the [OK/SEL] button simultaneously
For additional information about your remote
blink twice to confirm the programming.
for 3 seconds. The [CBL] button will turn
control, go to www.universalremote.com
on for 30 seconds.
*Note : To return TV device to CBL channel
STEP3 Press the first [DEVICE] button you want
repeat steps above replacing [TV] with
to store in the [SYSTEM ON/OFF] button
[CBL] in Step 3.
6
TV
Set-up Code Tables
Manufacturer/Brand
Set-Up Code Number
CBL-CABLE Converters
BOXLIGHT
266
Manufacturer/Brand
Set-Up Code Number
BRADFORD
043
BROCKWOOD
116
CISCO/SA
001 003 041 042 045 046
BROKSONIC
238
PIONEER
001 103 034 051 063 076 105
BYDESIGN
031 032
PACE
001 005 002
CANDLE
116 002 003 363
SAMSUNG
001 030
CAPEHART
058
MOTOROLA
002 111 148
CARY AUDIO DESIGN 266
CE-LABS
164
CELEBRITY
001
DIGEO
153
CENTURION
116
EVOLUTION FTA 158
CETRONIC
043
GENERAL INSTRUMENT 005 103 104
CHANGHONG
247
HAMLIN
049 050 055
CITIZEN
116 002 003 363 043 258 103 143
HITACHI
103 055
CLARION
043
JERROLD
005 004 103 005 003 008 009 010 069
CLASSIC
043
MAGNAVOX
010 012
CLP CLASSIC
333
MEMOREX
052
COBY
640 641 671
MOXI
111 252 153
COLORTYME
116
NFUSION
192
CONCERTO
363
PANASONIC
044 047
CONCIERGE
073
PHILIPS
006 012 013 020 085
CONTEC
043 050 051
PULSAR
052
CORNEA
116
RCA
047
CORONADO
143
REGAL
049 050
CRAIG
043 054
REGENCY
057
CROSLEY
164
SKY
230 204
CROWN
043 143
SONY
108
CURTIS MATHES 116 258 363 143
SPRUCER
047
CXC
043
TELNET
354
CYBERHOME
015
TOCOM
039 040 056
DAEWOO
363 016 043 044 076 103 114 125 127
TOSHIBA
052
143
VIEWSTAR
012 015
DAYTRON
363 143
ZENITH
052 060 093 100
DELL
320 164 363 618
DIGITAL PROJECTION 570
TV
DIMENSIA
333
DREAMVISION
235
Manufacturer/Brand
Set-Up Code Number
DUKANE
011 025
A MARK
112 143
DUMONT
116 073
ABEX
025
DURABRAND
096 052
ACCURIAN
036
DWIN
257
ADMIRAL
072 251 333
DYNASTY
043
AD NOTAM
672
DYNEX
400
ADVENT
247 388
EIKI
187
ADVENTURA
002
ELECTROBAND
001
AFFINITY
680
ELECTROGRAPH 466
AIKO
103
ELECTROHOME
143 024 076 196
AKAI
116 146 248 404 405 473 475 323 387
ELEKTRA
072
391 615
ELEMENT
363 494 526 622
ALBATRON
017
EMERSON
028 048 043 155 005 116 363 047 050
ALERON
028
051 076 096 143 153 154 052 514
AMERICA ACTION 043
ENVISION
116
AMPRO
073
EPSON
324 590
AMSTRAD
052
ESA
323
ANAM
043 054 056 080 112
FISHER
007 057
AOC
116 363 112 058 616
FUJITSU
246 198 410
APEX
572
FUNAI
028 043 052
APEX DIGITAL
006
FUSION
642
AQUAVISION
573 574
FUTURETECH
043
ASTAR
477
GATEWAY
242 268
AUDIOVOX
076 454 388
GE
073 116 008 009 034 056 074 155 333
AVENTURA
052
363
AVIELO
627 628
GEM
391
AVION
441
GIBRALTER
116 073
AXION
039
GO VIDEO
026
BELCOR
116
GOLDSTAR
113 116 102 363 106 112 127 143
BELL&HOWELL 333 072
GPX
674
BENQ
423 600
GRUNPY
028 043

Advertisement

loading

Summary of Contents for Universal Remote Control PHAZR-5 UR5U-9000

  • Page 1 The device LED will blink twice to code number 138. on/off with the [SYSTEM ON/OFF] button. CBL-CABLE Converters Macro buttons available(See Section 4), they The PHAZR-5 UR5U-9000 & UR5U-9020 is program. To program your TV, turn on HITACHI BOXLIGHT confirm that the code has been *Note : Ten blinks indicates the number 0.
  • Page 2 TV-LCD & Plasma TVs TV-LCD & Plasma TVs TV-Projectors AUDIO DVD-Blu-ray & HD DVD DVD-DVD/VCR Combos AUX-iPod Controls Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number Manufacturer/Brand...

This manual is also suitable for:

Phazr-5 ur5u-9020