Universal Remote Control PHAZR-5 UR5U-9000L Operating Instructions

Operating Instructions For 1 4
Introduction Button Functions
PHAZR-5
The PHAZR-5 UR5U-9000L & UR5U-9020L
is designed to operate the CISCO / SA,
Pioneer, Pace Micro, Samsung and
Motorola digital set tops, Plus the majority
Cable Remote Control
of TV, AUD, DVD and AUX equipment on
the market as shown below.
CBL : Cable Set-top Box TV : Televisions
UR5U-9000L & UR5U-9020L AUD : Audio Receivers DVD : DVD Players
AUX : Media PC, Gaming System, etc.
2
Replacing Batteries
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
5
Programming the Remote Control
3
Operations IMPORTANT SETUP NOTE!
In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV,
AUD, DVD or AUX button, depending on what device you are programming the remote to operate.
DEFAULT STATE:
Device Default: Cable Set-Top Box (STB) There are three ways you can program your remote:
* Quick Set-Up Method
Channel Default: CABLE channel and numbers
* The Pre-Programmed 3-Digit Code Method
through the CABLE STB. You have the option of
* The Auto-Search Method
controlling your CABLE channel and numbers
through the TV or AUD. Refer to section I for pro- The Quick Set-Up Method is a unique feature that enables the fastest and easiest setup by using a 1 digit code.
gramming steps. This is the quickest way to set up devices made by popular manufacturers.
The Pre-Programmed Code Method allows you to setup all of the buttons at once by entering 3-digit code
Volume Default: Volume and Mute control are
numbers that correspond with the components manufacturer/brand. Code tables for this method are on the
automatically transferred to the respective
backside of the operating instructions.
Component based on the Device selected:
The Auto-Search Method scans through all of the codes in the remote control, one at a time allowing you to
CBL:Cable Set-Top Box ; TV:TV ; AUD:AUD.
identify the correct code.
DVD:TV ; AUX:AUX. You have the option of
Universal Remote Control, Inc.
controlling CABLE Volume and Mute through IMPORTANT SETUP NOTE!
www.universalremote.com
the TV, DVD or AUD. Refer to section H for
This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you do
OCE-0081A Rev 12 (02/01/13)
programming steps. not press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.
A. Quick Set-Up Method DVD code number from the brand list.
Quick Number Manufacturer/Brand
STEP4 Store the three-digit code by pressing
STEP1 Turn on the component you want to
the same [DEVICE] button once again.
program. To program your TV, turn on 0 HITACHI
The device LED will blink twice to
1 SONY
the TV.
confirm that the code has been
2 PHILIPS
STEP2 Point the remote control at the compo-
stored.
3 SAMSUNG
nent.
4 PHILIPS MAGNAVOX
5 PANASONIC
STEP3 Press and hold the [DEVICE] key for 5
D. Auto-Search Method
6 LG
seconds until the Device LED will blink
7 JVC
If none of the three digit code numbers
once and stays on. Continue to hold
8 DENON
assigned to your brand of equipment works, or
the [DEVICE] key and press the num-
9 PIONEER
the code table does not list your brand, you can
ber key assigned to your brand in the
use the Auto Search Method to find the correct
Quick Set-up Code Table. The compo-
three-digit code number for your equipment by
nent should turn off as soon as the
following steps:
AUX
number key is pressed. (If it does not
Quick Number Manufacturer/Brand STEP1 Turn on the equipment that you want
turn off, release the [DEVICE] key and
the remote control to operate (Cable
0 BOSE
use the Pre-Programmed 3-Digit code
Box, TV, DVD, etc.).
1 HP
Method or Scanning Method.)
2 APPLE / iPod STEP2 Press the [DEVICE] button and the
STEP4 Release the [DEVICE] key to save the
3 APPLE / iPod [OK/SEL] button simultaneously for
code. The Device LED will blink twice
4 MICROSOFT / XBOX three seconds. The device LED will
5 SONY / PS2
to confirm that the code is stored.
turn on indicating that it is ready to be
6 LUTRON
programmed. The LED will remain on
Repeat the steps above for all components (TV,
7 X-10
for 30 seconds. The next step must be
AUD, DVD, AUX).
8 X-10
entered while the LED is on.
9 MICROSOFT / XBOX
STEP3 Press the [CH5] or [CH6] button one
B. Quick Set-up Code Tables
at a time or keep it pressed. The
remote will emit a series of Power
C. Pre-Programmed 3-Dight Code Method
ON/OFF code signals. Release the
TV
[CH+] or [CH-] button as soon as the
Quick Number Manufacturer/Brand STEP1 Turn on the equipment that you want
equipment turns off.
the remote control to operate (Cable
0 SANYO
Box, TV, DVD, etc.). *Note : You can verify that you have selected the
1 SONY
correct code by pressing the [POWER]
2 SAMSUNG STEP2 Press the [DEVICE] button and the
3 LG button. The equipment should turn back
[OK/SEL] button simultaneously for
4 TOSHIBA on. Then try all of the functions on the
three seconds. The corresponding
5 PANASONIC remote control (i.e. volume, mute, etc.) to
device LED will turn on indicating that
6 PHILIPS ensure you have the correct code. If any of
it is ready to be programmed. The LED
7 HITACHI the functions do not operate as they should,
will remain on for 30 seconds. The
8 SHARP repeat the instructions from STEP 3 above
next step must be entered while the
9 VIZIO
to continue the Auto Search Method.
LED is on.
STEP4 Press the same [DEVICE] button to
STEP3 Point the remote control toward the
store the code. The Device LED will
equipment and enter the three-digit
blink twice to confirm that the code
AUDIO
code number assigned to your brand
has been stored.
from the code tables. If there are more
Quick Number Manufacturer/Brand
than one three-digit number listed for
E. To Identify the 3-Digit Code
0 ROTEL
your brand, try one code number at a
1 DENON Programmed for a Device
time until your equipment turns off.
2 YAMAHA
STEP1 Press the appropriate [DEVICE] button
3 MARANTZ
*Note : You can verify that you have selected the
and the [OK/SEL] button simultaneously
4 SONY
correct code by pressing the [POWER]
for three seconds. The device LED will
5 INTEGRA
button. The equipment should turn back
turn on for 30 seconds. The next step
6 HARMAN KARDON
on. Then try all of the functions on the
must be performed while the LED is on.
7 PIONEER
remote control (i.e. volume, mute, etc.)
8 ONKYO
STEP2 Press the [INFO] button. The device LED
to ensure you have the correct code. If
9 LEXICON
will blink a number of times indicating
any of the functions do not operate as
the number of each digit for the code.
they should, repeat the instructions from
Each digit is separated by a one second
STEP 3 above using the next three digit
interval of the LED being off. and then press [POWER]. Repeat this for J. Programming a 'Macro' button.
the other components you want to turn
Example :One blink, (pause) three blinks,
If your remote model has custom-programmable
on/off with the [SYSTEM ON/OFF] button.
(pause) eight blinks indicates the
Macro buttons available(See Section 4), they
code number 138.
STEP4 Press the [CH5] button to save the can be programmed to act as a 'Macro' or
power commands you stored. The Favorite Channel button in CABLE mode. This
*Note : Ten blinks indicates the number 0.
[CBL] button will blink twice to confirm
allows you to program up to five 2-digit channels,
the commands have been saved.
four 3-digit channels or three 4-digit channels
F. Programming the AUX Device
that can be accessed with one button press.
H. Programming Volume Control
You can take advantage of the AUX function to STEP1 Press the [CBL] button to select the CBL
program a devices such as a media PC, gaming Volume and Mute control are factory programmed mode.
console or satellite radio receiver. Follow the to automatically transfer to the respective Device
STEP2 Press the [MACRO] button and
mode You select, as follows:
instruction in section C to program an AUX
[OK/SEL] button simultaneously for 3
device. You can also program the AUX button
seconds. The [CBL] button will turn on
CBL : CBL T V : TV AUD : AUD
for a second TV, DVD or Audio Device. To do
DVD : TV AUX : AUX for 30 seconds.
this follow the instructions below.
STEP3 Enter the the 2, 3 or 4-digit code for the
If you wish to store the TV volume control in
STEP1 Turn on the 5th device you want to
channel you want programmed first (for
CBL mode, use the following steps.
program (TV, AUD, DVD, etc.).
example, 007) using the Number Pad,
STEP1 Press the [OK/SEL] button and [CBL]
STEP2 Press the [AUX] button and the then press the [STOP] button. Then
button simultaneously for three
[OK/SEL] button simultaneously for 3 enter the code for the next channel (for
seconds. The device LED will turn on
example, 050), then press the [STOP]
seconds. The [AUX] device LED will
for 30 seconds. The next step must
button. Repeat this process for the third
turn on for 30 seconds.
be performed while the LED is on.
channel. The [CBL] button will blink
STEP3 Press the [Device] button For the type
once for each channel entered.
STEP2 Press the [VOL5] button. The device
of device you want to setup. Point the
LED will blink.
remote control toward the device and STEP4 Press the [CH5] button to store the
enter the 3-digit code number STEP3 Press [TV] button. The device LED will channels that were selected. The
assigned to your brand. blink twice to confirm the programming. [CBL] button will blink twice to confirm
the storage of commands.
*Note : To program a second TV press TV, etc. *Note : To return CBL device to CBL volume
repeat steps above replacing [TV] with To access the programmed channels, press
STEP4 When the equipment turns off verify
[CBL] in Step 3. the [MACRO] button once. This will bring up
that you have selected the correct
the first channel. Press once again and it will
code by pressing the [POWER] button.
bring up the second channel. Press again and
The equipment should turn back on. I. Programming Channel Control
it will bring up the third channel.
Then try all of the functions on the
You can program the channel controls (Channel
remote control (i.e. volume, mute, etc.) K. Low Battery Warning
Up, Channel Down, Last and Numbers) from
to ensure you have the correct code.
one Device to operate in another Device mode. When the batteries are low and need to be
If any of the functions do not operate
Default channel control settings on the remote
replaced with fresh batteries, the Device LED
as they should, enter the next 3-digit
control are as follows:
lights will blink 2 times in sequence whenever a
code number from the brand list.
[POWER] button is pressed to turn on equipment.
CBL : CBL T V : CBL AUD : AUD
STEP5 Once you have found the correct
DVD : DVD AUX : AUX
3-digit code, save it by pressing the L. Memory Lock System
[AUX] button one more time. The [AUX]
If you wish to store the TV channel controls in
This remote control is designed to retain pro-
LED light will blink twice to confirm the
TV mode, use the following steps.
grammed memory for 10 years even after batteries
code was stored.
STEP1 Press the [OK/SEL] button and [TV] button are removed from the remote control.
G. Programming the System On/Off Button
simultaneously for three seconds. The
M. Record Your Component Set-up Codes
device LED will turn on for 30 seconds.
This allows you to program the System On/Off
The next step must be performed while
TV Set-up Code Number:
button so it can send up to five power On/Off
the LED is on.
commands with one button press.
AUD Set-up Code Number:
STEP2 Press the [VOL6] button. The device
STEP1 Press the [CBL] button.
DVD Set-up Code Number:
LED will blink.
STEP2 Press the [SYSTEM ON/OFF] button
AUX Set-up Code Number:
STEP3 Press [TV] button. The device LED will
and the [OK/SEL] button simultaneously
blink twice to confirm the programming.
For additional information about your remote
for 3 seconds. The [CBL] button will turn
control, go to www.universalremote.com
*Note : To return TV device to CBL channel
on for 30 seconds.
repeat steps above replacing [TV] with
STEP3 Press the first [DEVICE] button you want
[CBL] in Step 3.
to store in the [SYSTEM ON/OFF] button
6 TV
Set-up Code Tables
Manufacturer/Brand Set-Up Code Number
CBL-CABLE Converters
BOXLIGHT 266
Manufacturer/Brand Set-Up Code Number BRADFORD 043
BROCKWOOD 116
CISCO/SA 001 003 041 042 045 046
BROKSONIC 238
PIONEER 001 103 034 051 063 076 105
BYDESIGN 031 032
PACE 001 005 002
CANDLE 116 002 003 363
SAMSUNG 001 030
CAPEHART 058
MOTOROLA 002 111 148
CARY AUDIO DESIGN 266
CE-LABS 164
CELEBRITY 001
DIGEO 153
CENTURION 116
EVOLUTION FTA 158
CETRONIC 043
GENERAL INSTRUMENT 005 103 104
CHANGHONG 247
HAMLIN 049 050 055
CITIZEN 116 002 003 363 043 258 103 143
HITACHI 103 055
CLARION 043
JERROLD 005 004 103 005 003 008 009 010 069
CLASSIC 043
MAGNAVOX 010 012
CLP CLASSIC 333
MEMOREX 052
COBY 640 641 671
MOXI 111 252 153
COLORTYME 116
NFUSION 192 CONCERTO 363
PANASONIC 044 047
CONCIERGE 073
PHILIPS 006 012 013 020 085
CONTEC 043 050 051
PULSAR 052 CORNEA 116
RCA 047 CORONADO 143
REGAL 049 050
CRAIG 043 054
REGENCY 057 CROSLEY 164
SKY 230 204 CROWN 043 143
SONY 108 CURTIS MATHES 116 258 363 143
SPRUCER 047 CXC 043
TELNET 354 CYBERHOME 015
DAEWOO 363 016 043 044 076 103 114 125 127
TOCOM 039 040 056
TOSHIBA 052 143
VIEWSTAR 012 015 DAYTRON 363 143
DELL 320 164 363 618
ZENITH 052 060 093 100
DIGITAL PROJECTION 570
TV
DIMENSIA 333
DREAMVISION 235
Manufacturer/Brand Set-Up Code Number
DUKANE 011 025
DUMONT 116 073
A MARK 112 143
DURABRAND 096 052
ABEX 025
DWIN 257
ACCURIAN 036
ADMIRAL 072 251 333 DYNASTY 043
DYNEX 400
AD NOTAM 672
EIKI 187
ADVENT 247 388
ADVENTURA 002 ELECTROBAND 001
ELECTROGRAPH 466
AFFINITY 680
ELECTROHOME 143 024 076 196
AIKO 103
ELEKTRA 072
AKAI 116 146 248 404 405 473 475 323 387
ELEMENT 363 494 526 622
391 615
EMERSON 028 048 043 155 005 116 363 047 050
ALBATRON 017
051 076 096 143 153 154 052 514
ALERON 028
ENVISION 116
AMERICA ACTION 043
EPSON 324 590
AMPRO 073
ESA 323
AMSTRAD 052
FISHER 007 057
ANAM 043 054 056 080 112
FUJITSU 246 198 410
AOC 116 363 112 058 616
FUNAI 028 043 052
APEX 572
FUSION 642
APEX DIGITAL 006
FUTURETECH 043
AQUAVISION 573 574
GATEWAY 242 268
ASTAR 477
GE 073 116 008 009 034 056 074 155 333
AUDIOVOX 076 454 388
363
AVENTURA 052
GEM 391
AVIELO 627 628
AVION 441 GIBRALTER 116 073
GO VIDEO 026
AXION 039
BELCOR 116 GOLDSTAR 113 116 102 363 106 112 127 143
BELL&HOWELL 333 072 GPX 674
GRUNPY 028 043
BENQ 423 600