Universal Remote Control UR5L-9000L-IP Operating Instructions

Operating Instructions For 1 4
Introduction Button Functions
PHAZR-5
The Phazr 5, UR5L-9000L-IP is designed
to operate virtually all IPTV, Digital and
DTA set top boxes plus the majority of TV,
AUD, DVD and AUX equipment on the
Cable Remote Control
market as shown below.
STB : Set-top Box TV : Televisions
AUD : Audio Receivers DVD : DVD Players
UR5L-9000L-IP AUX : Media PC, Gaming System, etc.
2
Replacing Batteries
Before you program or operate the remote
control, you must install two new AA
alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
BACK
install the batteries as shown in the
Return to previous menu screen or TV channel.
illustration below.
STEP3 Replace the battery compartment cover. IPTV company custom-programmable Macros.
Refer to Section M for programming steps.
My DVR
Digital Video Recording.
DELETE
Edit text on the screen.
5
Programming the Remote Control
3 IMPORTANT SETUP NOTE!
Operations
In this section when you are instructed to press a [DEVICE] button, that means to press either the STB, TV, AUD,
DVD or AUX button, depending on what device you are programming the remote to operate.
DEFAULT STATE:
Device Default: Set-Top Box (STB) There are four ways you can program your remote:
* Quick Set-Up Method
Channel Default: STB channel and numbers
* The Auto-Search Method
through the STB. You have the option of
controlling your STB channel and numbers The Quick Set-Up Method is a unique feature that enables the fastest and easiest setup by using a 1 digit
through the TV or AUD. Refer to section L for code. This is the quickest way to set up devices made by popular manufacturers.
programming steps.
The Pre-Programmed Code Method allows you to setup all of the buttons at once by entering 3-digit
code numbers that correspond with the components manufacture/brand. Code tables for this method
Volume Default: Volume and Mute control are
are on the backside of the operating instructions.
automatically transferred to the respective
Component based on the Device selected: The Auto-Search Method scans through all of the codes in the remote control, one at a time allowing you
to identify the correct code.
STB:Set-Top Box ; TV:TV ; AUD:AUD. DVD:TV ;
The Learning Method allows you to transfer functions from other remotes to the PHAZR-5one button at a time.
AUX:AUX. You have the option of controlling
Universal Remote Control, Inc.
STB Volume and Mute through the TV, DVD IMPORTANT SETUP NOTE!
www.universalremote.com
or AUD. Refer to section K for programming
This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you do
OCE-0087D REV 16 (08/26/16)
steps.
not press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.
A. Quick Set-Up Method
STEP1 Turn on the component you want to pro-
gram. To program your TV, turn on the TV.
STEP2 Press and hold the [DEVICE] key for 5
seconds until the Device LED will blink
once and stays on. Continue to hold the
Device Buttons used to select the component
you want to operate and signals remote control
[DEVICE] key and press the number key
activity.
assigned to your brand in the Quick
Set-up Code Table and release both
[DEVICE] key and the number key to
save the code. The Device LED will
blink twice to confirm that the code is
stored.
STEP3 Point the remote control at the compo-
nent.
STEP4 Press the power button. If it turns off, it
is programmed for your component. If it
does not turn off, use the Pre-
Programmed 3-Digit code Method or
Scanning Method.
Repeat the steps above for all components
INTERACTIVE (STB, TV, AUD, DVD, AUX).
View personalized weather, sports, and traffic.
B. Quick Set-up Code Tables
SKIP
Forward ahead in stored or recorded programs.
STB
ASPECT/ENTER
IPTV
TV
IPTV
IPTV
Quick Number Manufacturer/Brand
0 SANYO
IPTV
1 SONY
2 SAMSUNG
3 LG
4 TOSHIBA
IPTV
5 PANASONIC
6 PHILIPS
7 HITACHI
8 SHARP
9 VIZIO
AUDIO
Quick Number Manufacturer/Brand
0 ROTEL
1 DENON
2 YAMAHA
* The Pre-Programmed 3-Digit Code Method
3 MARANTZ
4 SONY
* The Learning Method
5 INTEGRA
6 HARMAN KARDON
7 PIONEER
8 ONKYO
9 LEXICON
DVD
Quick Number Manufacturer/Brand
0 HITACHI
1 SONY
2 PHILIPS
3 SAMSUNG
4 PHILIPS MAGNAVOX
5 PANASONIC
6 LG
7 JVC
8 DENON
9 PIONEER
AUX for 30 seconds. The next step must be simultaneously for 3 seconds until the
entered while the LED is on. Device LED light turns on.
Quick Number Manufacturer/Brand
STEP3 Press the [CH5] or [CH6] button one at STEP2 Press and hold both the [DEVICE] button
0 BOSE
a time or keep it pressed. The remote you want to erase and the [PAUSE] button
1 HP
will emit a series of Power ON/OFF
2 ONKYO for 5 seconds. The Device LED will blink
3 APPLE / iPod code signals. Release the [CH5] or [CH6] twice to confirm the erasure.
4 MICROSOFT / XBOX
button as soon as the equipment turns off.
STEP3 To exit, press and hold both the [DEVICE]
5 SONY / PS2
6 LUTRON *Note : You can verify that you have selected the and [ASPECT] buttons simultaneously
7 X-10
correct code by pressing the [POWER]
8 YAMAHA
H.To Identify the 3-Digit Code
button. The equipment should turn back
9 ROKU
on. Then try all of the functions on the
Programmed for a Device
remote control (i.e. volume, mute, etc.) to
ensure you have the correct code. If any of STEP1 Press the appropriate [DEVICE] button
C. Pre-Programmed 3-Dight Code Method
and the [OK/SEL] button simultaneously
the functions do not operate as they should,
repeat the instructions from STEP 3 above for three seconds. The device LED will
STEP1 Turn on the equipment that you want
to continue the Auto Search Method. turn on for 30 seconds. The next step
the remote control to operate (Set top
must be performed while the LED is on.
Box, TV, DVD, etc.). STEP4 Press the same [DEVICE] button to store
the code. The Device LED will blink twice
STEP2 Press the [INFO] button. The device LED
STEP2 Press the [DEVICE] button and the
to confirm that the code has been stored.
will blink a number of times indicating
[OK/SEL] button simultaneously for three
the number of each digit for the code.
seconds. The corresponding device LED E. The Learning Method
Each digit is separated by a one second
will turn on indicating that it is ready to
STEP1 Press the [DEVICE] button (TV,AUD, DVD, interval of the LED being off.
be programmed. The LED will remain on
or AUX) to be programmed and the
Example :One blink, (pause) three blinks,
for 30 seconds. The next step must be
[ASPECT] buttons simultaneously for 3
(pause) eight blinks indicates the
entered while the LED is on. seconds until the Device LED light turns on.
code number 138.
STEP3 Point the remote control toward the STEP2 Point the PHAZR-5 at the other remote,
*Note : Ten blinks indicates the number 0.
equipment and enter the three-digit head-to-head, 1 or 2 inches apart.
code number assigned to your brand
STEP3 Press the button on the PHAZR-5 that
I. Programming the AUX Device
from the code tables. If there are more
you want to teach a command to. For
You can take advantage of the AUX function to
than one three-digit number listed for example, press the [MUTE] button to
program a devices such as a media PC, gaming
your brand, try one code number at a learn a command to the [MUTE] button.
console or satellite radio receiver. Follow the
time until your equipment turns off.
STEP4 Press and hold the button on the other
instruction in section C to program an AUX
remote that corresponds to the command
*Note : You can verify that you have selected the
device. You can also program the AUX button for
you want to teach until the PHAZR-5
correct code by pressing the [POWER]
a second TV, DVD or Audio Device. To do this
Device LED light blinks twice.
button. The equipment should turn back
follow the instructions below.
on. Then try all of the functions on the *Note : The LED will blink 5 times if there
STEP1 Turn on the 5th device you want to
was an error in the learning process.
remote control (i.e. volume, mute, etc.) to
program (TV, AUD, DVD, etc.).
Repeat STEPS 3 and 4 if this occurs.
ensure you have the correct code. If any
Continue learning other buttons by STEP2 Press the [AUX] button and the
of the functions do not operate as they
repeating STEPS 3 and 4. [OK/SEL] button simultaneously for 3
should, repeat the instructions from
seconds. The [AUX] device LED will
STEP5 Once you have completed teaching the
STEP 3 above using the next three digit
turn on for 30 seconds.
PHAZR-5 all desired commands for the
code number from the brand list.
component, save the learned commands
STEP3 Press the [Device] button For the type of
STEP4 Store the three-digit code by pressing the
by pressing the [DEVICE] and [ASPECT] device you want to setup. Point the remote
same [DEVICE] button once again. The buttons simultaneously until the Device
control toward the device and enter the
device LED will blink twice to confirm that LED blinks 3 times. Now test all of the
3-digit code number assigned to your brand.
buttons to make sure they operate correctly.
the code has been stored.
*Note : To program a second TV press TV, etc.
F. Erasing a Single Learned Command
D. Auto-Search Method
STEP4 When the equipment turns off verify
STEP1 Press the [DEVICE] and [ASPECT] buttons
If none of the three digit code numbers assigned to that you have selected the correct
your brand of equipment works, or the code table simultaneously for 3 seconds until the
code by pressing the [POWER] button.
Device LED light turns on.
does not list your brand, you can use the Auto The equipment should turn back on.
Search Method to find the correct three-digit code
STEP2 Press and hold the button you want to Then try all of the functions on the
number for your equipment by following steps:
erase for 3 seconds. The Device LED remote control (i.e. volume, mute, etc.)
will blink twice to confirm the erasure.
STEP1 Turn on the equipment that you want to ensure you have the correct code.
the remote control to operate (Set top STEP3 To exit, press and hold both the [DEVICE] If any of the functions do not operate as
Box, TV, DVD, etc.).
and [ASPECT] buttons simultaneously they should, enter the next 3-digit code
until the Device LED blinks 3 times. number from the brand list.
STEP2 Press the [DEVICE] button and the
[OK/SEL] button simultaneously for
STEP5 Once you have found the correct 3-digit
G. Erasing All Learned Commands
three seconds. The device LED will turn
code, save it by pressing the [AUX] button
on indicating that it is ready to be from One Device
one more time. The [AUX] LED light will
programmed. The LED will remain on
blink twice to confirm the code was stored.
STEP1 Press the [DEVICE] and [ASPECT] buttons
J. Programming the System On/Off Button *Note : To return TV device to STB channel 6
Set-up Code Tables
repeat steps above replacing [TV] with
This allows you to program the System On/Off
[STB] in Step 3.
button so it can send up to five power On/Off
STB-IPTV
commands with one button press.
M. Programming a 'Macro' button. Manufacturer/Brand
STEP1 Press the [STB] button.
If your remote model has custom-programmable ADB
STEP2 Press the [SYSTEM ON/OFF] button
AMINO
Macro buttons available(See Section 4), they can
and the [OK/SEL] button simultaneously
AT&T
be programmed to act as a 'Macro' or Favorite
for 3 seconds. The [STB] button will CISCO
Channel button in STB mode. This allows you to
turn on for 30 seconds. COMCAST
program up to five 2-digit channels, four 3-digit
DREAM
STEP3 Press the first [DEVICE] button you want to
channels or three 4-digit channels that can be ENTONE
store in the [SYSTEM ON/OFF] button and
MINERVA
accessed with one button press.
then the [POWER] button. Repeat this for
MYRIO
STEP1 Press the [STB] button to select the STB
other Components until you have stored MOTOROLA
mode. NOW TV
all the desired power commands into the
PACE
[SYSTEM ON/OFF] button.
STEP2 Press the [MACRO] button and
SCIENTIFIC ATLANTA 251
STEP4 Press the [CH5] button to save the [OK/SEL] button simultaneously for
WEGENER
3 seconds. The [STB] button will turn
power commands you stored. The
STB-CABLE Converters
[STB] button will blink twice to confirm on for 30 seconds.
the commands have been saved.
STEP3 Enter the the 2, 3 or 4-digit code for the Manufacturer/Brand
channel you want programmed first
K. Programming Volume Control MOTOROLA
(for example, 007) using the Number
PACE
Volume and Mute control are factory programmed
Pad, then press the [STOP] button. PIONEER
to automatically transfer to the respective
Then enter the code for the next chan- SAMSUNG
Device mode You select, as follows: SCIENTIFIC ATLANTA/CISCO 001 003 041 042 045 046
nel (for example, 050), then press the
Amino
STB : STB T V : TV AUD : AUD [STOP] button. Repeat this process for
ARRIS
DVD : TV AUX : AUX the third channel. The [STB] button will
Cincinnati Bell
blink once for each channel entered. CISCO
If you wish to store the TV volume control in STB
COMCAST
mode, use the following steps.
STEP4 Press the [CH5] button to store the
Duoson
STEP1 Press the [OK/SEL] button and [STB] channels that were selected. The
ENTONE
[STB] button will blink twice to confirm
button simultaneously for three EVOLUTION
seconds. The device LED will turn on the storage of commands. INFOMIR
for 30 seconds. The next step must KAON
To access the programmed channels, press the
be performed while the LED is on. NAGRA
[MACRO] button once. This will bring up the
TECHNICOLOR
STEP2 Press the [VOL5] button. The device
first channel. Press once again and it will bring
WINDSTREAM
LED will blink.
up the second channel. Press again and it will
TV
bring up the third channel.
STEP3 Press [TV] button. The device LED will
Manufacturer/Brand
blink twice to confirm the programming.
N. Low Battery Warning
*Note : To return STB device to STB volume A MARK
repeat steps above replacing [TV] with When the batteries are low and need to be ACCURIAN
ADMIRAL
[STB] in Step 3. replaced with fresh batteries, the Device LED
AD NOTAM
lights will blink 2 times in sequence whenever a
ADVENT
L. Programming Channel Control
[POWER] button is pressed to turn on equip-
ADVENTURA
ment.
You can program the channel controls (Channel
AFFINITY
AKAI
Up, Channel Down, Last and Numbers) from
O. Memory Lock System
one Device to operate in another Device mode.
ALBATRON
Default channel control settings on the remote This remote control is designed to retain
ALERON
control are as follows:
programmed memory for 10 years even after
AMERICA ACTION 043
batteries are removed from the remote con-
STB : STB T V : STB AUD : AUD AMPRO
trol. AMSTRAD
DVD : DVD AUX : AUX
ANAM
If you wish to store the TV channel controls in TV
P. Record Your Component Set-up AOC
mode, use the following steps.
Codes APEX
APEX DIGITAL
STEP1 Press the [OK/SEL] button and [TV] button
TV Set-up Code Number: AQUAVISION
simultaneously for three seconds. The
ASTAR
device LED will turn on for 30 seconds. AUD Set-up Code Number:
AUDIOVOX
The next step must be performed while
DVD Set-up Code Number: AUVIO
the LED is on.
AVENTURA
AUX Set-up Code Number:
AVIELO
STEP2 Press the [VOL6] button. The device
For additional information about your remote AVION
LED will blink.
control, go to www.universalremote.com AXESS
STEP3 Press [TV] button. The device LED will
AXION
blink twice to confirm the programming. BELCOR
TV
Manufacturer/Brand Set-Up Code Number
BELL&HOWELL 333 072
BENQ 423 600
Set-Up Code Number
BOXLIGHT 266
254 255 315 259 BRADFORD 043
260 249 256 257 261 BROCKWOOD 116
251 BROKSONIC 238
313 251 316 BYDESIGN 031 032
313 CANDLE 116 002 003 363
159
CARY AUDIO DESIGN 266
155 258 213
CELEBRITY 001
178
CENTURION 116
254 255
CETRONIC 043
253
CHANGHONG 247
314
CIELO 714
313
Ciil 732
CITIZEN 116 002 003 363 043 258 143
250 CLARION 043
CLASSIC 043
CLP CLASSIC 333
COBY 640 641 671 363
Set-Up Code Number
COLORTYME 116
002 111 148 206 CONCERTO 363
001 005 002 206 217 CONCIERGE 073
001 103 034 051 063 076 105 CONTEC 043 050 051
001 030
CORNEA 116
CORONADO 143
219
CRAIG 043 054
172 216
CROSLEY 164
220
CROWN 043 143
209
CURTIS MATHES 116 258 363 143
195
CXC 043
218
CYBERHOME 015
210 221
DAEWOO 363 043 076 143
189 215
DAYTRON 363 143
207
DELL 320 164 363 618
208 DIGITAL PROJECTION 570
211 DIMENSIA 333
365 DREAMVISION 235
212 DUKANE 011
DUMONT 116 073
DURABRAND 052
Set-Up Code Number DWIN 257
DYNASTY 043
112 143
DYNEX 400
036
EIKI 187
072 251 333
ELECTROBAND 001
672
ELECTROGRAPH 466
247 388
ELECTROHOME 143 024 076
002
ELEKTRA 072
680 ELEMENT 363 494 526 622 690
116 248 404 405 473 475 323 387 391 EMERSON 028 048 043 116 363 050 051 076 143
615 154 052 514
017 ENVISION 116
028 EPSON 324 590
ESA 323
073 FISHER 007 057
052
FREEMOTION 688
043 054 056 080 112
FUJITSU 246 198 410
116 363 112 616 FUNAI 028 043 052
572 FUSION 642
006 724 FUTURETECH 043
573 574 686 GATEWAY 242 268
477 GE 073 116 008 009 034 056 333 363
076 454 388 GEM 391
689 GIBRALTER 116 073
052 GO VIDEO 026
627 628 GOLDSTAR 113 116 102 363 112 143
GPX 674
441
GRUNPY 028 043
711
HAIER 363 501 623
039
HALL MARK 363
116