Universal Remote Control PHAZR-5 UR5U-9000L Operating Instructions

Operating Instructions For 1 4
Introduction Button Functions
PHAZR-5
The PHAZR-5 UR5U-9000L & UR5U-9020L
is designed to operate the CISCO / SA,
Pioneer, Pace Micro, Samsung and
Motorola digital set tops, Plus the majority
Cable Remote Control
of TV, AUD, DVD and AUX equipment on
the market as shown below.
CBL : Cable Set-top Box TV : Televisions
UR5U-9000L & UR5U-9020L AUD : Audio Receivers DVD : DVD Players
AUX : Media PC, Gaming System, etc.
2
Replacing Batteries
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
5
Programming the Remote Control
3
Operations IMPORTANT SETUP NOTE!
In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV,
AUD, DVD or AUX button, depending on what device you are programming the remote to operate.
DEFAULT STATE:
Device Default: Cable Set-Top Box (STB) There are three ways you can program your remote:
* Quick Set-Up Method
Channel Default: CABLE channel and numbers
* The Pre-Programmed 3-Digit Code Method
through the CABLE STB. You have the option of
* The Auto-Search Method
controlling your CABLE channel and numbers
through the TV or AUD. Refer to section I for pro- The Quick Set-Up Method is a unique feature that enables the fastest and easiest setup by using a 1 digit code.
gramming steps. This is the quickest way to set up devices made by popular manufacturers.
The Pre-Programmed Code Method allows you to setup all of the buttons at once by entering 3-digit code
Volume Default: Volume and Mute control are
numbers that correspond with the components manufacturer/brand. Code tables for this method are on the
automatically transferred to the respective
backside of the operating instructions.
Component based on the Device selected:
The Auto-Search Method scans through all of the codes in the remote control, one at a time allowing you to
CBL:Cable Set-Top Box ; TV:TV ; AUD:AUD.
identify the correct code.
DVD:TV ; AUX:AUX. You have the option of
Universal Remote Control, Inc.
controlling CABLE Volume and Mute through IMPORTANT SETUP NOTE!
www.universalremote.com
the TV, DVD or AUD. Refer to section H for
This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you do
OCE-0081A REV 22 (08/28/15)
programming steps. not press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.
A. Quick Set-Up Method code number from the brand list.
DVD
STEP1 Turn on the component you want to pro- STEP4 Store the three-digit code by pressing
Quick Number Manufacturer/Brand
gram. To program your TV, turn on the TV. the same [DEVICE] button once again.
0 HITACHI
The device LED will blink twice to
STEP2 Press and hold the [DEVICE] key for 5 sec-
1 SONY
confirm that the code has been
onds until the Device LED will blink once
2 PHILIPS
stored.
and stays on. Continue to hold the 3 SAMSUNG
[DEVICE] key and press the number key 4 PHILIPS MAGNAVOX
assigned to your brand in the Quick Set-up 5 PANASONIC
D. Auto-Search Method
Code Table and release both [DEVICE] key 6 LG
If none of the three digit code numbers
and the number key to save the code. The 7 JVC
8 DENON assigned to your brand of equipment works, or
Device LED will blink twice to confirm that
9 PIONEER the code table does not list your brand, you can
the code is stored.
use the Auto Search Method to find the correct
STEP3 Point the remote control at the compo-
three-digit code number for your equipment by
nent.
following steps:
AUX
STEP4 Press the power button. If it turns off, it
STEP1 Turn on the equipment that you want
Quick Number Manufacturer/Brand
is programmed for your component. If
the remote control to operate (Cable
it does not turn off, use the Pre-
0 BOSE
Box, TV, DVD, etc.).
Programmed 3-Digit code Method or
1 HP
Scanning Method. 2 ONKYO STEP2 Press the [DEVICE] button and the
3 APPLE / iPod [OK/SEL] button simultaneously for
Repeat the steps above for all components
4 MICROSOFT / XBOX three seconds. The device LED will
(CBL, TV, AUD, DVD, AUX).
5 SONY / PS2
turn on indicating that it is ready to be
B. Quick Set-up Code Tables
6 LUTRON
programmed. The LED will remain on
7 X-10
for 30 seconds. The next step must be
CBL
8 YAMAHA
entered while the LED is on.
Quick Number Manufacturer/Brand
9 ROKU
STEP3 Press the [CH5] or [CH6] button one
0 PACE DTA
at a time or keep it pressed. The
1 SA/CISCO, SAMSUNG, PACE DIGITAL
remote will emit a series of Power
2 MOTOROLA DIGITAL
C. Pre-Programmed 3-Dight Code Method
3 MOTOROLA DTA ON/OFF code signals. Release the
4 EVOLUTION DTA [CH+] or [CH-] button as soon as the
STEP1 Turn on the equipment that you want
5 CISCO IPTV
equipment turns off.
the remote control to operate (Cable
6 ADB IPTV
7 TECHNICOLOR Box, TV, DVD, etc.). *Note : You can verify that you have selected the
8 AMINO 140/540 IPTV
correct code by pressing the [POWER]
STEP2 Press the [DEVICE] button and the
9 MOTOROLA IPTV
button. The equipment should turn back
[OK/SEL] button simultaneously for
TV on. Then try all of the functions on the
three seconds. The corresponding
remote control (i.e. volume, mute, etc.) to
Quick Number Manufacturer/Brand device LED will turn on indicating that
ensure you have the correct code. If any of
it is ready to be programmed. The LED
0 SANYO
the functions do not operate as they should,
will remain on for 30 seconds. The
1 SONY
repeat the instructions from STEP 3 above
2 SAMSUNG next step must be entered while the
to continue the Auto Search Method.
3 LG LED is on.
4 TOSHIBA
STEP4 Press the same [DEVICE] button to
STEP3 Point the remote control toward the
5 PANASONIC
store the code. The Device LED will
equipment and enter the three-digit
6 PHILIPS
blink twice to confirm that the code
code number assigned to your brand
7 HITACHI
has been stored.
8 SHARP from the code tables. If there are more
9 VIZIO than one three-digit number listed for
E. To Identify the 3-Digit Code
AUDIO your brand, try one code number at a
Programmed for a Device
time until your equipment turns off.
Quick Number Manufacturer/Brand
STEP1 Press the appropriate [DEVICE] button
0 ROTEL
*Note : You can verify that you have selected the
and the [OK/SEL] button simultaneously
1 DENON
correct code by pressing the [POWER]
for three seconds. The device LED will
2 YAMAHA
button. The equipment should turn back
turn on for 30 seconds. The next step
3 MARANTZ
on. Then try all of the functions on the
must be performed while the LED is on.
4 SONY
remote control (i.e. volume, mute, etc.)
5 INTEGRA
STEP2 Press the [INFO] button. The device LED
to ensure you have the correct code. If
6 HARMAN KARDON
will blink a number of times indicating
any of the functions do not operate as
7 PIONEER
the number of each digit for the code.
8 ONKYO they should, repeat the instructions from
Each digit is separated by a one second
9 LEXICON STEP 3 above using the next three digit
interval of the LED being off. and then press [POWER]. Repeat this for J. Programming a 'Macro' button.
the other components you want to turn
Example :One blink, (pause) three blinks,
If your remote model has custom-programmable
on/off with the [SYSTEM ON/OFF] button.
(pause) eight blinks indicates the
Macro buttons available(See Section 4), they
code number 138.
STEP4 Press the [CH5] button to save the can be programmed to act as a 'Macro' or
power commands you stored. The Favorite Channel button in CABLE mode. This
*Note : Ten blinks indicates the number 0.
[CBL] button will blink twice to confirm
allows you to program up to five 2-digit channels,
the commands have been saved.
four 3-digit channels or three 4-digit channels
F. Programming the AUX Device
that can be accessed with one button press.
H. Programming Volume Control
You can take advantage of the AUX function to STEP1 Press the [CBL] button to select the CBL
program a devices such as a media PC, gaming Volume and Mute control are factory programmed mode.
console or satellite radio receiver. Follow the to automatically transfer to the respective Device
STEP2 Press the [MACRO] button and
mode You select, as follows:
instruction in section C to program an AUX
[OK/SEL] button simultaneously for 3
device. You can also program the AUX button
seconds. The [CBL] button will turn on
CBL : CBL T V : TV AUD : AUD
for a second TV, DVD or Audio Device. To do
DVD : TV AUX : AUX for 30 seconds.
this follow the instructions below.
STEP3 Enter the the 2, 3 or 4-digit code for the
If you wish to store the TV volume control in
STEP1 Turn on the 5th device you want to
channel you want programmed first (for
CBL mode, use the following steps.
program (TV, AUD, DVD, etc.).
example, 007) using the Number Pad,
STEP1 Press the [OK/SEL] button and [CBL]
STEP2 Press the [AUX] button and the then press the [STOP] button. Then
button simultaneously for three
[OK/SEL] button simultaneously for 3 enter the code for the next channel (for
seconds. The device LED will turn on
example, 050), then press the [STOP]
seconds. The [AUX] device LED will
for 30 seconds. The next step must
button. Repeat this process for the third
turn on for 30 seconds.
be performed while the LED is on.
channel. The [CBL] button will blink
STEP3 Press the [Device] button For the type
once for each channel entered.
STEP2 Press the [VOL5] button. The device
of device you want to setup. Point the
LED will blink.
remote control toward the device and STEP4 Press the [CH5] button to store the
enter the 3-digit code number STEP3 Press [TV] button. The device LED will channels that were selected. The
assigned to your brand. blink twice to confirm the programming. [CBL] button will blink twice to confirm
the storage of commands.
*Note : To program a second TV press TV, etc. *Note : To return CBL device to CBL volume
repeat steps above replacing [TV] with To access the programmed channels, press
STEP4 When the equipment turns off verify
[CBL] in Step 3. the [MACRO] button once. This will bring up
that you have selected the correct
the first channel. Press once again and it will
code by pressing the [POWER] button.
bring up the second channel. Press again and
The equipment should turn back on. I. Programming Channel Control
it will bring up the third channel.
Then try all of the functions on the
You can program the channel controls (Channel
remote control (i.e. volume, mute, etc.) K. Low Battery Warning
Up, Channel Down, Last and Numbers) from
to ensure you have the correct code.
one Device to operate in another Device mode. When the batteries are low and need to be
If any of the functions do not operate
Default channel control settings on the remote
replaced with fresh batteries, the Device LED
as they should, enter the next 3-digit
control are as follows:
lights will blink 2 times in sequence whenever a
code number from the brand list.
[POWER] button is pressed to turn on equipment.
CBL : CBL T V : CBL AUD : AUD
STEP5 Once you have found the correct
DVD : DVD AUX : AUX
3-digit code, save it by pressing the L. Memory Lock System
[AUX] button one more time. The [AUX]
If you wish to store the TV channel controls in
This remote control is designed to retain pro-
LED light will blink twice to confirm the
TV mode, use the following steps.
grammed memory for 10 years even after batteries
code was stored.
STEP1 Press the [OK/SEL] button and [TV] button are removed from the remote control.
G. Programming the System On/Off Button
simultaneously for three seconds. The
M. Record Your Component Set-up Codes
device LED will turn on for 30 seconds.
This allows you to program the System On/Off
The next step must be performed while
TV Set-up Code Number:
button so it can send up to five power On/Off
the LED is on.
commands with one button press.
AUD Set-up Code Number:
STEP2 Press the [VOL6] button. The device
STEP1 Press the [CBL] button.
DVD Set-up Code Number:
LED will blink.
STEP2 Press the [SYSTEM ON/OFF] button
AUX Set-up Code Number:
STEP3 Press [TV] button. The device LED will
and the [OK/SEL] button simultaneously
blink twice to confirm the programming.
For additional information about your remote
for 3 seconds. The [CBL] button will turn
control, go to www.universalremote.com
*Note : To return TV device to CBL channel
on for 30 seconds.
repeat steps above replacing [TV] with
STEP3 Press the first [DEVICE] button you want
[CBL] in Step 3.
to store in the [SYSTEM ON/OFF] button
6 TV
Set-up Code Tables
Manufacturer/Brand Set-Up Code Number
CBL-CABLE Converters
AQUAVISION 573 574 686
Manufacturer/Brand Set-Up Code Number ASTAR 477
AUDIOVOX 076 454 388
CISCO/SA 001 003 041 042 045 046
AUVIO 689
PIONEER 001 103 034 051 063 076 105
AVENTURA 052
PACE 001 002 005 206
AVIELO 627 628
SAMSUNG 001 030
AVION 441
MOTOROLA 002 111 148 206
AXESS 711
ARRIS 172
AXION 039
CE-LABS 164
BELCOR 116
COMCAST 195
BELL&HOWELL 333 072
DIGEO 153
BENQ 423 600
EVOLUTION 189
BOXLIGHT 266
EVOLUTION FTA 158
BRADFORD 043
GENERAL INSTRUMENT 005 103 104
BROCKWOOD 116
HAMLIN 049 050 055
BROKSONIC 238
HITACHI 103 055
BYDESIGN 031 032
JERROLD 005 004 103 005 003 008 009 010 069
CANDLE 116 002 003 363
MAGNAVOX 010 012
CARY AUDIO DESIGN 266
MEMOREX 052
CELEBRITY 001
MOXI 111 252 153
CENTURION 116
NFUSION 192
CETRONIC 043
PANASONIC 044 047
CHANGHONG 247
PHILIPS 006 012 013 020 085
CIELO 714
PULSAR 052
CITIZEN 116 002 003 363 043 258 143
RCA 047
CLARION 043
REGAL 049 050
CLASSIC 043
REGENCY 057
CLP CLASSIC 333
SKY 230 204
COBY 640 641 671 363
SONY 108
COLORTYME 116
SPRUCER 047
CONCERTO 363
TECHNICOLOR 365
CONCIERGE 073
TELNET 354
CONTEC 043 050 051
TOCOM 039 040 056
CORNEA 116
TOSHIBA 052
CORONADO 143
VIEWSTAR 012 015
CRAIG 043 054
WINDSTREAM 212
CROSLEY 164
ZENITH 052 060 093 100
CROWN 043 143
CURTIS MATHES 116 258 363 143
CBL-IPTV
CXC 043
Manufacturer/Brand Set-Up Code Number
CYBERHOME 015
DAEWOO 363 043 076 143
ADB 254
DAYTRON 363 143
AMINO 260
DELL 320 164 363 618
CISCO 313
DIGITAL PROJECTION 570
ENTONE 213
DIMENSIA 333
MOTOROLA 253
DREAMVISION 235
DUKANE 011
TV
DUMONT 116 073
Manufacturer/Brand Set-Up Code Number
DURABRAND 052
DWIN 257
A MARK 112 143
DYNASTY 043
ACCURIAN 036
DYNEX 400
ADMIRAL 072 251 333
EIKI 187
AD NOTAM 672
ELECTROBAND 001
ADVENT 247 388
ELECTROGRAPH 466
ADVENTURA 002
ELECTROHOME 143 024 076
AFFINITY 680
ELEKTRA 072
AKAI 116 248 404 405 473 475 323 387 391 615
ELEMENT 363 494 526 622 690
ALBATRON 017
EMERSON 028 048 043 116 363 050 051 076 143
ALERON 028
154 052 514
AMERICA ACTION 043
ENVISION 116
AMPRO 073
EPSON 324 590
AMSTRAD 052
ESA 323
ANAM 043 054 056 080 112
FISHER 007 057
AOC 116 363 112 616
FREEMOTION 688
APEX 572
FUJITSU 246 198 410
APEX DIGITAL 006 724
FUNAI 028 043 052