Universal Remote Control PHAZR-5 Operating Instructions

Operating Instructions For 1 4
Introduction Button Functions
PHAZR-5
The PHAZR-5 UR5U-9000 & UR5U-9020 is
designed to operate the CISCO / SA,
Pioneer, Pace Micro, Samsung and
Motorola digital set tops, Plus the majority
Cable Remote Control
of TV, AUD, DVD and AUX equipment on
the market as shown below.
CBL : Cable Set-top Box TV : Televisions
UR5U-9000 & UR5U-9020 AUD : Audio Receivers DVD : DVD Players
AUX : Media PC, Gaming System, etc.
2
Replacing Batteries
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
5
Programming the Remote Control
3
Operations IMPORTANT SETUP NOTE!
In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV,
AUD, DVD or AUX button, depending on what device you are programming the remote to operate.
DEFAULT STATE:
Device Default: Cable Set-Top Box (STB) There are three ways you can program your remote:
* Quick Set-Up Method
Channel Default: CABLE channel and numbers
* The Pre-Programmed 3-Digit Code Method
through the CABLE STB. You have the option of
* The Auto-Search Method
controlling your CABLE channel and numbers
through the TV or AUD. Refer to section I for pro- The Quick Set-Up Method is a unique feature that enables the fastest and easiest setup by using a 1 digit code.
gramming steps. This is the quickest way to set up devices made by popular manufacturers.
The Pre-Programmed Code Method allows you to setup all of the buttons at once by entering 3-digit code
Volume Default: Volume and Mute control are
numbers that correspond with the components manufacturer/brand. Code tables for this method are on the
automatically transferred to the respective
backside of the operating instructions.
Component based on the Device selected:
The Auto-Search Method scans through all of the codes in the remote control, one at a time allowing you to
CBL:Cable Set-Top Box ; TV:TV ; AUD:AUD.
identify the correct code.
DVD:TV ; AUX:AUX. You have the option of
Universal Remote Control, Inc.
controlling CABLE Volume and Mute through IMPORTANT SETUP NOTE!
www.universalremote.com
the TV, DVD or AUD. Refer to section H for
This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you do
OCE-0081C REV 20 (10/10/17)
programming steps. not press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.
DVD STEP4 Store the three-digit code by pressing
the same [DEVICE] button once again.
Quick Number Manufacturer/Brand
The device LED will blink twice to
0 HITACHI
confirm that the code has been
1 SONY
stored.
2 PHILIPS
3 SAMSUNG
4 PHILIPS MAGNAVOX D. Auto-Search Method
5 PANASONIC
If none of the three digit code numbers
6 LG
assigned to your brand of equipment works, or
7 JVC
the code table does not list your brand, you can
8 DENON
use the Auto Search Method to find the correct
9 PIONEER
three-digit code number for your equipment by
following steps:
AUX
STEP1 Turn on the equipment that you want
Quick Number Manufacturer/Brand
the remote control to operate (Cable
0 BOSE
Box, TV, DVD, etc.).
1 HP
STEP2 Press the [DEVICE] button and the
2 ONKYO
[OK/SEL] button simultaneously for
3 APPLE / iPod
three seconds. The device LED will
4 MICROSOFT / XBOX
turn on indicating that it is ready to be
5 SONY / PS2
programmed. The LED will remain on
6 LUTRON
for 30 seconds. The next step must be
7 X-10
8 YAMAHA entered while the LED is on.
CBL
9 ROKU
STEP3 Press the [CH5] or [CH6] button one
at a time or keep it pressed. The
remote will emit a series of Power
C. Pre-Programmed 3-Dight Code Method
ON/OFF code signals. Release the
[CH+] or [CH-] button as soon as the
STEP1 Turn on the equipment that you want
equipment turns off.
the remote control to operate (Cable
Box, TV, DVD, etc.). *Note : You can verify that you have selected the
correct code by pressing the [POWER]
STEP2 Press the [DEVICE] button and the
button. The equipment should turn back
[OK/SEL] button simultaneously for
on. Then try all of the functions on the
three seconds. The corresponding
remote control (i.e. volume, mute, etc.) to
TV
device LED will turn on indicating that
ensure you have the correct code. If any of
it is ready to be programmed. The LED
the functions do not operate as they should,
will remain on for 30 seconds. The
repeat the instructions from STEP 3 above
next step must be entered while the
to continue the Auto Search Method.
LED is on.
STEP4 Press the same [DEVICE] button to
STEP3 Point the remote control toward the
store the code. The Device LED will
equipment and enter the three-digit
blink twice to confirm that the code
code number assigned to your brand
has been stored.
from the code tables. If there are more
than one three-digit number listed for
E. To Identify the 3-Digit Code
your brand, try one code number at a
Programmed for a Device
time until your equipment turns off.
AUDIO
STEP1 Press the appropriate [DEVICE] button
Quick Number Manufacturer/Brand
*Note : You can verify that you have selected the
and the [OK/SEL] button simultaneously
correct code by pressing the [POWER]
0 ROTEL for three seconds. The device LED will
1 DENON button. The equipment should turn back
turn on for 30 seconds. The next step
2 YAMAHA on. Then try all of the functions on the
must be performed while the LED is on.
3 MARANTZ
remote control (i.e. volume, mute, etc.)
STEP2 Press the [INFO] button. The device LED
4 SONY
to ensure you have the correct code. If
5 INTEGRA
will blink a number of times indicating
any of the functions do not operate as
6 HARMAN KARDON
the number of each digit for the code.
they should, repeat the instructions from
7 PIONEER
Each digit is separated by a one second
STEP 3 above using the next three digit
8 ONKYO
interval of the LED being off.
code number from the brand list.
9 LEXICON
Example :One blink, (pause) three blinks, and then press [POWER]. Repeat this for J. Programming a 'Macro' button.
(pause) eight blinks indicates the the other components you want to turn
If your remote model has custom-programmable
code number 138. on/off with the [SYSTEM ON/OFF] button.
Macro buttons available(See Section 4), they
*Note : Ten blinks indicates the number 0.
STEP4 Press the [CH5] button to save the can be programmed to act as a 'Macro' or
power commands you stored. The Favorite Channel button in CABLE mode. This
[CBL] button will blink twice to confirm
allows you to program up to five 2-digit channels,
F. Programming the AUX Device
the commands have been saved.
four 3-digit channels or three 4-digit channels
that can be accessed with one button press.
You can take advantage of the AUX function to
program a devices such as a media PC, gaming
STEP1 Press the [CBL] button to select the CBL
H. Programming Volume Control
console or satellite radio receiver. Follow the
mode.
instruction in section C to program an AUX
Volume and Mute control are factory programmed STEP2 Press the [MACRO] button and
device. You can also program the AUX button
to automatically transfer to the respective Device [OK/SEL] button simultaneously for 3
for a second TV, DVD or Audio Device. To do
mode You select, as follows: seconds. The [CBL] button will turn on
this follow the instructions below.
for 30 seconds.
CBL : CBL T V : TV AUD : AUD
STEP1 Turn on the 5th device you want to
DVD : TV AUX : AUX STEP3 Enter the the 2, 3 or 4-digit code for the
program (TV, AUD, DVD, etc.).
channel you want programmed first (for
If you wish to store the TV volume control in
STEP2 Press the [AUX] button and the
example, 007) using the Number Pad,
CBL mode, use the following steps.
[OK/SEL] button simultaneously for 3
then press the [STOP] button. Then
seconds. The [AUX] device LED will
STEP1 Press the [OK/SEL] button and [CBL] enter the code for the next channel (for
turn on for 30 seconds.
button simultaneously for three example, 050), then press the [STOP]
button. Repeat this process for the third
STEP3 Press the [Device] button For the type seconds. The device LED will turn on
channel. The [CBL] button will blink
of device you want to setup. Point the for 30 seconds. The next step must
once for each channel entered.
remote control toward the device and be performed while the LED is on.
enter the 3-digit code number
STEP2 Press the [VOL5] button. The device STEP4 Press the [CH5] button to store the
assigned to your brand.
LED will blink. channels that were selected. The
[CBL] button will blink twice to confirm
*Note : To program a second TV press TV, etc. STEP3 Press [TV] button. The device LED will
the storage of commands.
blink twice to confirm the programming.
STEP4 When the equipment turns off verify
To access the programmed channels, press
that you have selected the correct
*Note : To return CBL device to CBL volume
the [MACRO] button once. This will bring up
code by pressing the [POWER] button. repeat steps above replacing [TV] with
the first channel. Press once again and it will
The equipment should turn back on.
[CBL] in Step 3.
bring up the second channel. Press again and
Then try all of the functions on the
it will bring up the third channel.
I. Programming Channel Control
remote control (i.e. volume, mute, etc.)
to ensure you have the correct code.
K. Low Battery Warning
You can program the channel controls (Channel
If any of the functions do not operate
Up, Channel Down, Last and Numbers) from
as they should, enter the next 3-digit When the batteries are low and need to be
one Device to operate in another Device mode.
code number from the brand list.
replaced with fresh batteries, the Device LED
Default channel control settings on the remote
lights will blink 2 times in sequence whenever a
STEP5 Once you have found the correct
control are as follows:
[POWER] button is pressed to turn on equipment.
3-digit code, save it by pressing the
CBL : CBL T V : CBL AUD : AUD
[AUX] button one more time. The [AUX]
L. Memory Lock System
DVD : DVD AUX : AUX
LED light will blink twice to confirm the
code was stored. This remote control is designed to retain pro-
If you wish to store the TV channel controls in
grammed memory for 10 years even after batteries
TV mode, use the following steps.
are removed from the remote control.
STEP1 Press the [OK/SEL] button and [TV] button
G. Programming the System On/Off Button
simultaneously for three seconds. The
M. Record Your Component Set-up Codes
This allows you to program the System On/Off device LED will turn on for 30 seconds.
TV Set-up Code Number:
button so it can send up to five power On/Off The next step must be performed while
commands with one button press. the LED is on.
AUD Set-up Code Number:
STEP2 Press the [VOL6] button. The device
STEP1 Press the [CBL] button. DVD Set-up Code Number:
LED will blink.
STEP2 Press the [SYSTEM ON/OFF] button AUX Set-up Code Number:
STEP3 Press [TV] button. The device LED will
and the [OK/SEL] button simultaneously
For additional information about your remote
blink twice to confirm the programming.
for 3 seconds. The [CBL] button will turn
control, go to www.universalremote.com
on for 30 seconds.
*Note : To return TV device to CBL channel
STEP3 Press the first [DEVICE] button you want repeat steps above replacing [TV] with
to store in the [SYSTEM ON/OFF] button
[CBL] in Step 3.
6 TV
Set-up Code Tables
Manufacturer/Brand Set-Up Code Number
CBL-CABLE Converters
AQUAVISION 573 574 686
Manufacturer/Brand Set-Up Code Number ASTAR 477
AUDIOVOX 076 454 388
CISCO/SA 001 003 041 042 045 046
AVENTURA 052
PIONEER 001 103 034 051 063 076 105
Avera 761
PACE 001 002 005 206 217
AVIELO 627 628
SAMSUNG 001 030
AVION 441
MOTOROLA 002 111 148 206
AXESS 711
ARRIS 172 216
AXION 039
CE-LABS 164
BELCOR 116
COMCAST 195
BELL&HOWELL 333 072
Cox Digital Cable 223
BENQ 423 600
DIGEO 153
BOXLIGHT 266
Digital Multimedia Technology 222
EVOLUTION 189 215 BRADFORD 043
EVOLUTION FTA 158 BROCKWOOD 116
GENERAL INSTRUMENT 005 103 104 BYDESIGN 031 032
HAMLIN 049 050 055 CANDLE 116 002 003 363
HITACHI 103 055
CARY AUDIO DESIGN 266
Horizon 225
CELEBRITY 001
JERROLD 005 004 103 005 003 008 009 010 069
CENTURION 116
MAGNAVOX 010 012
CETRONIC 043
MEMOREX 052
CHANGHONG 247
MOXI 111 252 153
CIELO 714
NFUSION 192
Ciil 732
PANASONIC 044 047
CITIZEN 116 002 003 363 043 258 143
PHILIPS 006 012 013 020 085
CLARION 043
Pico Digital 224
CLASSIC 043
PULSAR 052
CLP CLASSIC 333
RCA 047
REGAL 049 050 COBY 640 641 671 363
REGENCY 057 COLORTYME 116
SKY 230 204 240 241 CONCERTO 363
SONY 108 CONCIERGE 073
SPRUCER 047
CONTEC 043 050 051
TECHNICOLOR 365
Continu-us 161 746 747
TELNET 354
CORNEA 116
TOCOM 039 040 056
CORONADO 143
TOSHIBA 052
CRAIG 043 054
VIEWSTAR 012 015
CROSLEY 164
WINDSTREAM 212
CROWN 043 143
ZENITH 052 060 093 100
CURTIS MATHES 116 258 363 143
CBL-IPTV
CXC 043
CYBERHOME 015
Manufacturer/Brand Set-Up Code Number
DAEWOO 363 043 076 143
ADB 254 DAYTRON 363 143
AMINO 260 DELL 320 164 363 618
CISCO 313 DIGITAL PROJECTION 570
ENTONE 213 DIMENSIA 333
MOTOROLA 253 DREAMVISION 235
DUKANE 011
TV
DUMONT 116 073
Manufacturer/Brand Set-Up Code Number DURABRAND 052
DWIN 257
A MARK 112 143
DYNASTY 043
ACCURIAN 036
DYNEX 400
ADMIRAL 072 251 333
EIKI 187
AD NOTAM 672
ELECTROBAND 001
ADVENT 247 388
ELECTROGRAPH 466
ADVENTURA 002
ELECTROHOME 143 024 076
AFFINITY 680
ELEKTRA 072
AKAI 116 248 404 475 323 387 391 615
ELEMENT 363 494 526 622 690
ALBATRON 017
EMERSON 028 048 043 116 363 050 051 076 143
ALERON 028
154 052 514
AMERICA ACTION 043
ENVISION 116
AMPRO 073
EPSON 324 590
AMSTRAD 052
ESA 323
ANAM 043 054 056 080 112
Evervue 755
AOC 116 363 112 616
APEX 572 FISHER 007 057
APEX DIGITAL 006 724 FUJITSU 246 198 410