Advertisement
Quick Links
Technology
TECHNICAL
Transmitter frequency
SPECIFICATION
Transmitter radiated power
Transmitter power density
Mounting height
• FALCON DR
• FALCON XL-DR
Tilt angles
Detection zone
• FALCON DR
(mounting height of 5m)
• FALCON XL-DR
(mounting height of 2.5m)
Detection mode
Minimum speed
Supply voltage
Mains frequency
Power consumption
Two Output relay (free of potential change-over contact)
• Max. contact voltage
• Max. contact current
• Max. switching power
DESCRIPTION OF
THE SENSOR
INSTALLATION
TIPS
The sensor must be firmly
fastened to prevent from
vibrating.
75.5268.01 20070111
FALCON DR: double relay / high mount • FALCON XL-DR: double relay / low mount
: Microwave and
microprocessor
: 24.125 GHz
: <20 dBm EIRP
: < 5 mW/cm²
: from 11.5' (3.5m) to 23' (7m)
: from 6.5' (2m) to 11.5' (3.5m)
: 0° to 180° in elevation
: 13' (W) x 16' (D)
4m (W) x 5m (D)
: 13' (W) x 6.5' (D)
4m (W) x 2m (D)
: Motion
: 2 in (5cm)/s (measured in the
sensor axis)
: 12V to 24V AC ±10%
12V to 24V DC +30% / -10%
: 50 to 60 Hz
: < 2W (VA)
: 42V AC
: 1A (resistive)
: 30W (DC) / 60VA (AC)
The sensor must not be placed
directly behind a panel or any kind
of material.
FALCON DR / FALCON XL-DR
MOTION SENSORS FOR INDUSTRIAL DOORS
Hold time
Temperature range
Degree of protection
Norm conformity
Dimensions
Weight
Material of housing
Material of bracket
Length of cable
Manual adjustment
• Orientation of sensing field (mechanically)
• Multiple functions (by push buttons)
Remote control adjustments
• Sensitivity
• Hold time
• Detection mode
• Pedestrian and parallel traffic rejection mode
• Output configuration
• Security
The sensor must not have
any object likely to move or
vibrate in its sensing field.
USER'S GUIDE
: 0.5s to 9s (adjustable)
: -22°F to +122°F (-30°C to +60°C)
: IP65
: R&TTE 1999/5/EC
EMC 89/336/EEC
: 4" (W) x 5" (D) x 3 ¾" (H)
102 mm (W) x 127 mm (D) x 96 mm (H)
: 0.88 lbs (0.4 kg)
: ABS and polycarbonate
: Anodized aluminium
: 33' (10m)
Tranceiver module
(planar antenna)
Green LED
Infrared Receiver
Red LED
2 Push Buttons
Microprocessor
Terminal block
The sensor must not have any
fluorescent lighting in its
sensing field.
Page 1 of 7
Advertisement
Related Manuals for BEA FALCON DR
Summary of Contents for BEA FALCON DR
- Page 1 FALCON DR: double relay / high mount • FALCON XL-DR: double relay / low mount Technology TECHNICAL Transmitter frequency SPECIFICATION Transmitter radiated power Transmitter power density Mounting height • FALCON DR • FALCON XL-DR Tilt angles Detection zone • FALCON DR (mounting height of 5m) •...
- Page 2 OPENING AND CLOSING THE SENSOR • Loosen the retaining nut until the cable slides easily into the grommet ; • Partially unscrew the 2 front cover screws ; • Pull out the front cover with the 2 front cover screws. BRACKET MOUNTING WIRING...
-
Page 3: Led Signal
SENSING FIELD DIMENSIONS H = 16.5 ft. S = 9 FALCON (Mounting height: 11.5’ (3.5 m) H = 11.5 ft. S = 9 FALCON XL (Mounting height: 8’ (2.5 m) H = 8 ft. S = 9 • When the power is turned ON the red and green LED flash for a few seconds. LED SIGNAL •... -
Page 4: Configuration Of The Sensor
DESCRIPTION OF THE INFRARED REMOTE CONTROL CONFIGURATION WITH REMOTE CONTROL 0-9 Number keys (1) Output redirection (2) Plus (3) Unlock (4) Minus (5) Holdtime (6) Sensitivity (7) Detection mode (8) Rejection mode (9) CONFIGURATION OF THE SENSOR Every adjustment session using the infrared remote control must start with unlocking and end with a double locking. The table below lists the parameters able to be adjusted by remote control and the operations required in order to adjust these parameters. - Page 5 Note: All parameters or functions listed in the following tables are only accessible if the sensor is in adjustment session. The red LED is then slowly flashing. During an adjustment session each parameter may be checked or changed at any time in the following way: PARAMETERS ACTIONS CHECK...
-
Page 6: Configuration With Push Buttons
OUTPUT Key 2: towards or away mode detection REDIRECTION Motion towards the detector triggers relay 1. Motion away from the detector triggers relay 2. OUTPUT Press the OUTPUT CONFIGURATION key (17). CONFIGURA- Use the NUMBER keys 1-4 (1) to select the required output configuration : TION Active Detection... - Page 7 SYMPTOM TROUBLE- SHOOTING The door will not open and no red LED lights up. The door opens and closes constantly. The sensor will not unlock when access code is entered. The sensor does not respond to the remote control. COMPANY CONTACT 75.5268.01 20070111 PROBABLE CAUSE...