Denon AVR-X1200W Service Manual page 28

Paths to be confirmed
Analog Amp Assign
A 0 7 : A S S I G N - Z 2
(Amp Assign : ZONE2)
6 fig.06
3.4.6. Confirmation items for the video system
See the block diagram fig.XXth.
Paths to be confirmed
Analog Video pass
V 0 1 : V I D E O
1
fig.07
HDMI pass
V 0 3 : H D M I
(MAIN ZONE)
2
fig.08
HDMI CEC
V 0 4 : H D M I
(Control Monitor : HDMI Monitor1)
3
fig.09
HDMI Audio
V 0 5 : H . A U D I O - A V R
(Audio : AVR)
4
fig.04
HDMI Audio
V 0 6 : H . A U D I O - T V
(Audio : TV)
5
fig.10
GUI
V 0 7 : G U I
fig.11
6
Display
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : STEREO
Z2 Source : Source
Vol -60dB
Amp assign : ZONE2
MAIN ZONE : ON
ZONE2 : ON
Display
Input Source : CBL/SAT
P A S S
Video Convert (IP Scaler) : OFF, All sources
MAIN ZONE ON
ZONE2 ON
Input Source : CBL/SAT
P A S S
Video Convert (IP Scaler) : OFF, All sources
MAIN ZONE ON
ZONE2 OFF
Input Source : CBL/SAT
C E C
HDMI Control : ON
Control Monitor : Monitor1 (if checking the HDMI Monitor Out1)
MAIN ZONE ON
ZONE2 OFF
Input Source : CBL/SAT
HDMI Control : OFF
HDMI Audio : AVR (if checking the audio output from AVR)
HDMI Audio : TV (if checking the audio output from TV)
Input Source : CBL/SAT
M E N U O N
Video Convert(IP Scaler) : ON, All sources
IP Scaler : "Analog & HDMI", All sources
Resolution : "AUTO", All sources
Setup Menu : ON
MAIN ZONE ON
ZONE2 OFF
Settings
・ Analog input ⇒ Speaker output (Surround Back (ZONE2) L/R)
・ Analog input ⇒ Pre OUT output (ZONE2 L/R)
(b The input source can be switched to any source except CBL/SAT.)
(b Volume -60dB is the value when Relative settings are used. The value is -20 when Absolute settings are used)
Settings
・ Component input ⇒ Component output (S710 / X1200E3 ONLY)
(b The input source can be switched to any source except CBL/SAT.)
・ HDMI input (MAIN function) ⇒ HDMI output(MAIN).
(b The input source can be switched to any source except CBL/SAT.)
・ When the power supply of a TV is put in the standby mode, make sure that the power supply of this unit is also put in the
standby mode.
(b The input source can be switched to any source except CBL/SAT.)
・ The ARC path can also be checked (check this using the TV input source).
・ HDMI input (PCM , DolbyDigital , DTS) ⇒ Speaker output.
・ HDMI input(HD audio) ⇒ Speaker output.
(b The input source can be switched to any source except CBL/SAT.)
・ HDMI input (PCM , DolbyDigital , DTS) ⇒ HDMI output (audio output from connected TV)
(b The input source can be switched to any source except CBL/SAT.)
・GUI display ⇒ HDMI output.
(b The input source can be switched to any source except CBL/SAT.)
28
What to confirm
What to confirm