Denon AVR-X1200W Service Manual page 27

3.4. DIAGNOSTIC MODE (Service Path Check Mode)
3.4.1. Actions
This function is convenient for confirming problem paths in the product and checking the paths after repairing.
The Video and Audio paths can be checked.
The backup data is not rewritten.
3.4.2. Starting up
AVR-X1200W
While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power.
AVR-S710W
While holding down buttons "TUNER PRESET CH +", "TUNE -" and "TUNE +" simultaneously, press the power button to turn on the power.
Select "1.SERVICE CHECK", then press the "STATUS" button to activate the diagnostic mode.
The "TUNED", "STEREO" and "RDS" segments are lit in this mode.
3.4.3. Canceling diagnostic mode
Press the power button to turn off the power.
3.4.4. Selecting items to check
Press the q button to switch between video items and audio items.
Press the w or e button to select the previous or next item.
The unit
q w
Actions
Audio ⇔ Video PREVIOUS
Button DIMMER QUICK SELECT 1
3.4.5. Audio system confirmation items
See the block diagram fig.XXth.
Paths to be confirmed
Analog
A 0 1 : A N A L O G
fig.01
1
DIGITAL
A 0 2 : D I G I T A L
(MAIN)
fig.02a
2
fig.02b
DIGITAL
A 0 3 : D I G I T A L - Z 2
(ZONE2)
fig.03a
3
fig.03b
HDMI
A 0 5 : H D M I
fig.04a
fig.04b
4
Analog AD
A 0 6 : A D
(MAIN)
fig.05a
5 fig.05b
Remote control unit
e q w
NEXT Audio ⇔ Video PREVIOUS
QUICK SELECT 2 SLEEP CURSOR 0
Display
Input Source : CBL/SAT
P A S S
Input Mode : Analog (fixed)
Sound mode : DIRECT
Amp assign : Surround Back
MAIN ZONE : ON
ZONE2 : OFF
Input Source : CBL/SAT
Input Mode : DIGITAL (fixed)
Sound mode : MULTI CH STEREO
Amp assign : Surround Back
Speaker Config ALLSpeaker = Small/SW=Yes(2ch)
MAIN ZONE ON
ZONE2 OFF
Input Source : NETWORK
Input Mode : Auto
Sound mode : STEREO
Amp assign : ZONE2
MAIN ZONE : ON
ZONE2 : ON
Input Source : CBL/SAT
Input Mode : HDMI (fixed)
Sound mode : STEREO
Amp assign : Surround Back
MAIN ZONE : ON
ZONE2 : OFF
Input Source : CBL/SAT
Input Mode : Analog (fixed)
Sound mode : MULTI CH STEREO
Vol-60dB
Amp assign : Surround Back
Speaker Config ALL Speaker = Small / SW = Yes(2ch)
MAIN ZONE : ON
ZONE2 : OFF
e
NEXT
CURSOR 1
Settings
・ Analog input ⇒ Speaker output (Front L/R)
(b The input source can be switched to any source except CBL/SAT.)
・ Digital input ⇒ Speaker output (Front L/R, Center, Surround L/R, Surround Back L/R)
・ Digital input ⇒ Pre output (Front L/R, Center, Surround L/R, Surround Back L/R, Subwoofer)
(b The input source can be switched to any source except CBL/SAT.)
・ Digital(PCM) input ⇒ Speaker output (Surround Back (ZONE2) L/R)
・ Digital(PCM) input ⇒ Pre OUT output (ZONE2 L/R) (AVR-X1200 only)
・ HDMI input ⇒ Speaker output (Front L/R)
(b The input source can be switched to any source except CBL/SAT.)
・ Analog input ⇒ Speaker output (Front L/R, Center, Surround L/R, Surround Back L/R)
・ Analog input ⇒ Speaker output, SW(20Hz) (Front L/R, Center, Surround L/R, Surround Back L/R)
(b The input source can be switched to any source except CBL/SAT.)
(b Volume -60dB is the value when Relative settings are used. The value is -20 when Absolute settings are used)
27
What to confirm