Vision Fitness S7100 Assembly Manual page 2

BLUE BAG
STEP 1
Please follow the order and intent of these
instructions as much as you can. The order
of assembly and order of tightening the
bolts will affect the performance of your
NOTE: A second person will be helpful to
new exercise machine.
complete this step.
• Slide the console mast boot onto the
console mast.
• Using the two bolts inserted in the front
of the console mast as guides, set the
console mast into the console mast
frame bracket ensuring cables are not
pinched between the console mast and
console mast bracket. Secure the front
of the mast to the frame bracket with the
other two socket head bolts (M8x20L)
and (8.2x16x1.5T) washers using a 6mm
L-shaped wrench. Secure each side of the
console mast to the console mast bracket
with one socket head bolt (M8x20L) and
one washer (8.2x16x1.5T) using a 6mm
L-shaped wrench. Do NOT tighten the
bolts yet.
• Release the console mast elevation
bracket and slide it down the console
mast to its lowest position. Slide the
console mast elevation bracket (shaft
bracket) over the elevation motor tube
so the holes in the console mast elevation
bracket line up with the top holes in
the elevation motor tube. Insert the bolt
(3/8x52L) and washer (10.2x15x1.5T)
and tighten just to snug using a 6mm
L-shaped wrench. Do not allow the bolt to
draw tight and deform the tube.
• Tighten the six (M8x20L) bolts on the
mast completely tight using a 6mm
L-shaped wrench.
• Connect the data cables coming from the
bottom of the console mast to the data
Incline Arm
cables coming up from the frame.
• Slide the console mast boot down over
the frame.
BLACK BAG
STEP 2
NOTE: Do not fully tighten the four bolts
at the bottom of the incline arm until
instructed to do so in step 4.
Incline Frame
• Slide the incline frame pivot shaft into Pivot Shaft
the incline pivot tube at the rear of the
unit.
• Slide the bottom of the left incline
arm over the incline pivot shaft and
let it rotate forward resting it on the
ground. Repeat on the right side.
NOTE: The incline frame pivot shaft
should be centered in the incline
pivot tube. Insert a button head bolt (
M10x25L) and washer (10.5x45x5T) into
each side of the incline frame pivot shaft.
Tighten the two button head bolts using
two 6mm L-shaped wrenches to pull the
incline arms in snug against the incline
STEP 3
pivot tube.
• Do NOT tighten the four bolts at the
bottom of the incline arm.
LIGHT BLUE BAG
STEP 3
NOTE: A second person will be helpful to
complete this step.
• Lift the left incline arm and place a top
tube (they are interchangeable) over the
left incline arm bracket and connect with
two socket head cap bolts (M8x70L),
and two washers (8.2x25x1.5T). Turn
bolts finger tight with the 6mm L-shaped
wrench.
• Insert the pin on the elevation bracket
into the hole on the front flange of the
connection arm.
• Repeat these steps on the right side.
PURPLE BAG
STEP 4
• When both top tubes are onto elevation
bracket alignment pin, lift the entire
assembly slightly to line up the bolt
holes. Insert the four socket head cap
bolts (M8x30L) through these holes.
Secure each bolt with a nylon nut (M8).
Do NOT tighten these bolts yet.
• Tighten the left and right top tube/
incline arm bolts using a 6mm L-shaped
wrench.
• Tighten the four elevation bracket bolts
(M8x30L) with the 6mm L-shaped
wrench and 13mm wrench.
• Tighten the four bolts at the bottom
lower-rear pivot of the incline arms using
a 6mm L-shaped wrench.
Console Mast
STEP 1
Data Cable
Elevation
Bracket
Console Mast
Boot
Elevation
Motor Tube
STEP 2
Incline
Pivot Tube
Top Tube
Elevation
Bracket
Incline Arm
Top Tube
Elevation
Bracket
Incline Arm
STEP 4
TIGHTEN
TIGHTEN
Suspension
Arm
Console Mast
Frame Bracket
Pedal
Assembly
STEP 5
STEP 7
Incline Frame
Cover
Elevation
Bracket Cover
Crank Arm
Incline Arm
Bracket
Dual-Action
Arm
Dual-Action Arm
Housing Shaft
STEP 6
Link Arm
PREMIER
DELUXE
CONSOLES
Heart
Rate Wires
Data Cables
PINK BAG
STEP 5
• Take the left pedal assembly lay it on
the ground in position on the left side of
the machine and insert the bearing end
of the suspension arm into the bracket
of the incline arm. From the outside,
insert a hex head bolt (M8x90L) with
flat washer (M8) through the bracket
and suspension arm. Secure with a flat
washer (M8), and hex nut (M8). Fully
tighten with two 13mm wrenches. This
joint must be VERY tight.
• Repeat this step on right side.
• Take the front end of the left pedal arm
and insert it into the end of the crank
arm (You will have to slightly pry the
pedal arm out in order to place it into
the bearing). Rotate the crank arm/
pedal arm connection up to the 11 o'clock
position (1 o'clock right side) and insert
the button head bolt (M8x15L) with flat
washer (8.2x25x2.5T). Tighten with the
5mm L-shaped wrench.
• Press inner crank arm bearing end cap
in place.
• Repeat this step on the right side.
GREEN BAG
STEP 6
• Remove button head cap bolt, flat washer
and one wavy washer from the left hand
dual-action arm housing shaft. Then
slide the left dual-action arm on the left
housing and secure in place with a button
head cap bolt (M8x20L) wavy washer
and flat washer. Tighten with the 5mm
L-shaped wrench.
• Insert a spacer bushing onto each side
of the left hand link arm bearing. Slide
the link arm between the flanges of
the dual-action arm bracket. Insert a
button head screw (M8x50L) and flat
washer (8.2x16x2T); through the hole
to connect the brackets. Secure with a
washer (8.2x16x2T) and nylon nut (M8).
Tighten with the 5mm L-shaped wrench
and 13mm wrench.
• Repeat these steps on the right side.
ORANGE BAG
STEP 7
• With the screwdriver, remove the four
console mounting screws from the
backside of the console. Connect the
heart rate wires coming from the mast
to the heart rate wires coming from the
bottom of the console. Plug the data
cables into the board. Tuck any extra
wires into the console. Take care to
ensure cables coming from the frame sit
in the groove in the back of the console
and do not get pinched. Secure console
to the bracket using the four console
mounting screws removed earlier.
Tighten with the screwdriver.
• Position the cover over the elevation
bracket and secure with two bolts
(M5x15L).
• Position the covers over the rear of the
incline frame and secure each cover in
place with four bolts (M5x15L) each.
Tighten the bolts just until the covers
are snug.
• Plug the power cord into the power
socket in the front of the unit. Plug the
other end of the cord into the wall outlet.
Make sure the power switches at the
bottom of the unit and on the back of
the console are in the on position.