Printing Quality Problems - Samsung CLX-6200FX User Manual

POSSIBLE
CONDITION
CAUSE
The machine If you are under the
DOS environment,
prints, but the
the font setting for
text is wrong,
your machine may
garbled, or
be set incorrectly.
incomplete.
Before printing, Using damp paper
can cause vapor
the machine
during printing.
emits vapor near
the output tray.
The machine Paper size and
paper size setting do
does not print
not match.
special sized
paper such as a
billing paper.

Printing quality problems

If the inside of the machine is dirty or paper has been loaded improperly,
you may notice a reduction in print quality. See the table below to clear the
problem.
CONDITION SUGGESTED SOLUTIONS
Light or faded print If a vertical white streak or faded area appears
on the page:
• The toner supply is low. You may be able
to temporarily extend the toner cartridge
life. See page 66. If this does not improve
the print quality, install a new toner
cartridge.
• The paper may not meet paper
specifications; for example, the paper is too
moist or too rough. See page 33.
• If the entire page is light, the print
resolution setting is too low. Adjust the print
resolution. See the help screen of the
printer driver.
• A combination of faded or smeared defects
may indicate that the toner cartridge needs
cleaning.
• The surface of the LSU part inside the
machine may be dirty. Clean the LSU,
contact a service representative.
Toner specks • The paper may not meet specifications; for
example, the paper is too moist or too
AaBbCc
rough. See page 33.
AaBbCc
• The paper path may need cleaning. See
"Cleaning the inside" on page 63.
AaBbCc
AaBbCc
AaBbCc
84 _Troubleshooting
SUGGESTED SOLUTIONS
Suggested solutions: Change
the font setting. See
"Changing the font
setting" on page 31.
This is not a problem. Just
keep printing.
Set the correct paper size in
the Custom in the Paper tab
in the printer propeties. See
Software section.
CONDITION SUGGESTED SOLUTIONS
Dropouts If faded areas, generally rounded, occur
randomly on the page:
AaBbCc
• A single sheet of paper may be defective.
Try reprinting the job.
AaBbCc
• The moisture content of the paper is
AaBbCc
uneven or the paper has moist spots on its
AaBbCc
surface. Try a different brand of paper. See
page 33.
AaBbCc
• The paper lot is bad. The manufacturing
processes can cause some areas to reject
toner. Try a different kind or brand of
paper.
• Change the printer option and try again. Go
to printer properties, click Paper tab, and
set type to Thick Paper. Refer to the
Software section for details.
If these steps do not correct the problem,
contact a service representative.
White spots appear on the page:
White Spots
• The paper is too rough and a lot of dirt from
the paper falls to the inner devices within
the machine, which means the transfer belt
may be dirty. Clean the inside of your
machine. Contact a service representative.
• The paper path may need cleaning.
Contact a service representative.
Vertical lines If black vertical streaks appear on the page:
• The drum inside the toner cartridge has
probably been scratched. Remove the
toner cartridge and install a new one. See
page 66.
If white vertical streaks appear on the page:
• The surface of the LSU part inside the
machine may be dirty. Clean the LSU,
contact a service representative.
If vertical streaks appear on the page:
• The surface of the scanner glass and its
white sheet may be dirty. Clean these unit.
See 65 . If this problem persists, contact a
service representative.
Color or Black If the amount of background shading becomes
unacceptable:
background
• Change to a lighter weight paper. See
page 33.
• Check the machine's environment: very dry
(low humidity) or high humidity (higher than
80% RH) conditions can increase the
amount of background shading.
• Remove the old toner cartridge and install
a new one. See page 66.