Ice Maker; Remove / Replace The Refrigerator; Remove The Refrigerator; Replace The Refrigerator - Norcold Polar N7V Service Manual

For information about ice maker operation and troubleshooting,
please refer to the separate Ice Maker Service document.
CAUTION
!
The rear of the refrigerator has sharp
corners. To prevent cuts or abrasions
when working on the refrigerator, be
careful and wear cut resistant gloves.

Remove the Refrigerator

1. Close the valve at the propane gas tanks(s) of the vehicle.
To avoid possible propane gas leaks, al-
WARNING
!
ways use two (2) wrenches to loosen and
ATTENTION
tighten the propane gas supply lines at the
refrigerator's manual shut off valve.
2. Open the lower intake vent and remove the propane gas
supply line from the 3/8 inch male flare fitting of the refrig-
erator.
3. Unplug the AC power cord from the receptacle.
4. Remove the DC wiring from the battery or the converter of
the vehicle.
5. Put a mark on the DC wires so that you can put them back
in the correct location.
6. Remove the DC wires from the refrigerator.
7. Remove the screws which fasten the rear mounting flange
of the refrigerator to the floor.
8. Remove the plastic plugs from the lower plastic trim of the
refrigerator.
9. Remove the screws that go through the lower plastic trim,
the lower mounting bracket, and into the floor.
10. Remove the upper plastic trim by pulling it off of the upper
mounting bracket.
11. Remove the screws in the upper mounting bracket which
fasten the refrigerator to the wall.
Very heavy object. Do not attempt to
WARNING
!
remove without help. Unassisted attempts
ATTENTION
will likely cause bodily injury, property
damage, or both.
12. Remove the refrigerator from the opening.
Polar Series N7V, N7X, N7XL / N8V, N8X, N8XL

REMOVE / REPLACE THE REFRIGERATOR

ICE MAKER

Replace the Refrigerator

WARNING
!
ATTENTION
1. Push the refrigerator completely into the enclosure.
WARNING
!
ATTENTION
2. Put the screws through the upper mounting bracket and into
the wall.
3. Push the upper trim plastic trim onto the upper mounting
bracket.
4. Push the lower plastic trim onto the lower mounting bracket.
5. Put two screws through the lower plastic trim, the lower
mounting bracket, and into the floor.
6. Open the lower intake vent and put the screws through the
rear mounting flange of the refrigerator into the floor.
7. Connect the DC wires from the refrigerator.
8. Connect the DC wiring to the battery or the converter.
9. Push the AC power cord into the receptacle.
WARNING
!
ATTENTION
10. Attach the propane gas supply line to the 3/8 inch male flare
fitting of the refrigerator.

Conduct Leak Test

1. Open the valve of the propane gas tank(s) of the vehicle.
WARNING
!
ATTENTION
WARNING
!
ATTENTION
2. Using a leak checking solution, examine the gas supply line
connections for leaks. No leaks are allowed.
60
Very heavy object. Do not attempt to
install without help. Unassisted attempts
will likely cause bodily injury, property
damage, or both.
Make sure the combustion seal is not
broken, is completely around the refrig-
erator mounting flanges, and is between
the mounting flanges and the wall of the
enclosure. If the combustion seal is not
complete, exhaust fumes can be pres-
ent in the living area of the vehicle. The
breathing of exhaust fumes can cause
dizziness, nausea, and in extreme cases,
death.
To avoid possible propane gas leaks, al-
ways use two (2) wrenches to loosen and
tighten the propane gas supply lines at the
refrigerator's manual shut off valve.
Do not allow the leak checking solution
to touch the electrical components. Many
liquids are electrically conductive and can
cause a shock hazard, electrical shorts,
and in some cases, fire.
Do not use any leak test solution that
contains ammonia or chlorine. Ammonia
and chlorine corrode brass and copper
components.
www.norcold.com