Juniper SRX550 Quick Start page 3

Task 7: Configure the Basic Settings
1. Click the Start button at the bottom of the Introduction page. You can configure the
basic settings, such as the hostname, domain name, and root password for your
services gateway.
NOTE: All fields marked in the Introduction page with an asterisk (*) are required. All
network and management access settings are optional.
2. In the Configure System: Identification page:
a. Type the hostname of the services gateway; for example, devicea.
b. Type the domain name of the services gateway; for example, lab.device.net.
c. Type the root password; for example,
dnmcx243.23...D9Y2gXF9ac==root@devicea.lab.device.net.
3. If you have used Method 2 in Task 5 to obtain a static IP address for your services
gateway, ensure that you make the following modifications in the J-Web interface:
a. From the Configure System: Network Settings page of the wizard, type the IP
address (for example, 10.0.0.1/24) of the default gateway in the Default
Gateway field and server names in the DNS Servers list. Your ISP provides the
IP address for the gateway and the server names.
NOTE: You can optionally configure DNS servers and searches, interface groups
(VLANs), current system time and time zone, and NTP servers.
Sample Settings on the SRX550 Services Gateway
SRX550 Services Gateway Property
Services gateway hostname
IP address for default gateway (optional)
IP address of the NTP server used to synchronize system
time
IP address of the DNS server to which DNS requests are sent 10.148.2.32
Domains to which the services gateway belongs
4. From the Configure Interfaces page of the wizard, click the interface you want to
configure (for example, ge-0/0/0.0), and click Edit.
5. On the Add/Edit interface page, next to Address, clear DHCP and select IP
Address.
6.
7.
Task 8: Apply the Basic Configuration
To apply the configuration settings for the services gateway:
1.
2.
After configuring the basic settings, the J-Web setup wizard redirects you to the J-Web
pages where you can continue working in the J-Web user interface.
IMPORTANT: After you complete initial setup configuration, the initial J-Web setup
wizard will be no longer available unless you reset the services gateway to the factory
Sample Value
default settings and reboot it. You can perform additional setup by using the J-Web user
devicea
interface or the CLI interface. You can use the J-Web wizards to configure firewall
policies, VPN settings, and NAT rules.
10.0.0.1/24
10.148.2.21
NOTE: To make any changes to the interface configuration, see the Branch SRX Series
Services Gateways Golden Configurations at
http://www.juniper.net/us/en/local/pdf/app-notes/3500153-en.pdf .
lab.device.net and device.net
Task 9: Verify the Configuration
Access http://www.juniper.net to ensure that you are connected to the Internet. This
connectivity ensures that you can pass traffic through the services gateway.
NOTE: If the http://www.juniper.net page does not load, verify your configuration settings,
and ensure that you have correctly applied the configuration.
After you have completed these steps, you can pass traffic from any trust port to the
untrust port.
Using the Reset Config Button
If a configuration fails or denies management access to the services gateway, you can
use the Reset Config button to restore the device to the factory default configuration or to
a rescue configuration. For example, if someone inadvertently commits a configuration
that denies management access to the services gateway, you can delete the invalid
configuration and replace it with a rescue configuration by pressing the Reset Config
button.
In the IP Address/subnet field, enter the manual IP address provided by your ISP.
The IP address must be entered in a.b.c.d/xx format, where xx is the subnet prefix.
Click Add.
NOTE: Make sure that you have selected the required services and protocols under
Services (Inbound) and Protocols (Inbound). Select all to permit all protocols and
services.
From the J-Web Preferences page in the J-Web starting page options, select the tab
you want to appear on startup.
From the Configure J-Web Preferences page, use the J-Web commit option to
specify when you want the commit to occur.
IMPORTANT: Ensure that you have configured the IP address, root authentication,
and default gateway before you commit the configuration.
Review the configuration on the Review & Commit page. Click Commit to save the
configuration, or click Back to make changes.
Page 3