Page 1 NT631/631C Programmable Terminal Operation Manual Produced March 1999...
Page 2 OMRON Product References All OMRON products are capitalized in this manual. The word “Unit” is also capitalized when it refers to an OMRON product, regardless of whether or not it appears in the proper name of the product. The abbreviation “Ch,” which appears in some displays and on some OMRON products, often means “word”...
Page 3: Table Of Contents
..........Using a Memory Unit (NT631/NT631C with V1) .
Page 4 ......... 11-3 Maintenance of the NT631/NT631C .
Page 5 ........D. Transporting and Storing the NT631/NT631C .
Page 6: About This Manual
Section 2 gives basic information on the method for connecting to the host and communication methods, and describes the names and functions of the parts of the NT631/NT631C. Section 3 describes how to make the settings at the NT631/NT631C, and how to connect it to peripheral devices.
Page 7 [Creating and transferring screen data] S NT-series Support Tool Operation Manual (V053-E1-j) The screens displayed on the NT631/631C are created with the support tool and transferred to the NT631/631C. This manual describes how to create and trans- fer screen data.
Page 8: Precautions
PRECAUTIONS This section provides general precautions for using the Programmable Terminal. The information contained in this section is important for the safe and reliable application of the Programmable Ter- minal. You must read this section and understand the information contained before attempting to set up or operate a Programmable Terminal.
Page 9: Intended Audience
Meanings This operation manual uses the following conventions and symbols to indicate cautions, warnings, and dangers in order to esure safe use of the NT631/631C. The caustions, warnings, and dangers shown here contain important information related to safety. This instructions in these cautions, warnings, and dangers must be observed.
Page 10 Precautions WARNING Do not attempt to take the unit apart and do not touch any inter- nal parts while the power is being supplied. Doing either of these may result in electrical shock. WARNING Switch OFF the NT631C power before replacing the backlight. Otherwise you could sustain an electric shock.
Page 11 "# $ %...
Page 12 ! ...
Page 13 ' ...
Page 15 * % ' ' + $ 7+- & % ...
Page 16 E # 23 # # # E : !"#$$%&##$$'(#...
Page 17 " # # $ 0 !"&1%2!"&1)2!"&*) !"#2!"#) % !34.5#234).5#'( !34.5#234).5'( !366$'(& -07 8 ! 9 ! 7 :%&&) ) ;$ $ % 6 ...
Page 18 $ " " " # " " " " " " " " $ " "...
Page 19 " ! # " " " " & " " " " " # # " " " " " " "...
Page 20 % & & # # # # # ' ...
Page 21 >3 ? % " ' # < . 0 / 3...
Page 22 H : '# # # # # # # 6 # # # # > ? % ...
Page 23 I# J ; ...
Page 24 # J00K I00K ! # ...
Page 26 & ! ' ! ! # ! ...
Page 27 -# & . ! % 6 ! . # )7 # ...
Page 28 " * + 2 ! A # ! $ ! ...
Page 29 " 3 -0 8 : A !"#2!"#) 5 6, '4 333,33) '( & # 9 '( & "" # 5 62 '4 333,3,) ! L >? ! L * # *++ 0 6 # ...
Page 30 / 8 : 6 !"#2!"#) + -./ -. 1 + -./ -!. + ../ -0. , " 7 + % 7 983,33 8 ! $ ...
Page 31 8 F/ 8 : A !"#2!"#) # # ! ! ! : * # ...
Page 32 # - ! 1-#234(-#234 6 >! ? 6 # ! A # & N2% ! O...
Page 33 6 # 6 L * ! !"#2!"#) 2* 1 0 7!( (!( 005...
Page 34 ! "# ! "# $! %& $ # # &# " - & ) ( 7 & +8 ,' -- 5--8 $ &# >! 7 ?# # # ! ...
Page 35 ! "# " % - & ) ( 9 & : $ & # # " # &...
Page 36 $ (! # + # 8!!2)$= C >7 3 ? / $ %. * B '&-.'&- " : " " ...
Page 37 $ ' 5 ' *7,* ' BC7=BC 7= 24 8 , & +30 '/...
Page 38 % ) # + B !"#2!"#) % ( & / ( / : & & ? % 6 " " 6" B8...
Page 39 % , " 'E % . . ! % ! % ;+2; (1+$'#$ % ! % ;+2; (1+$'#$ %F%.6) )7.# 9G . &"&$'#$ %F%.6) )7.#6 9G . #D$'#$...
Page 40: Section 2 Preparing For Connection
SECTION 2 Preparing for Connection This section describes the connection methods that are possible with the NT631/NT631C, and the functions of the parts of NT631/NT631C, as the required knowledge before connecting to the host and to the peripheral devices. Method for Connection to the Host .
Page 41: Method For Connection To The Host
NT631/NT631C, and the relationship between the connection method and the communication method. 2-1-1 Connection Method and Communication Method S NT631/NT631C communication ports and communication methods The NT631/NT631C has two communication ports. Their uses are indicated in the table below. Communication Port Usable Communication Methods Communication Type...
Page 42 S Combinations of communication method and connection method The connection methods that can be used depending on the communication method used and the communication type for communication between the NT631/NT631C and the host are indicated in the table below. Usable Communication Method...
Page 43 NT631/NT631C side for communication with the host, but in this case one NT- AL001 unit is required for each NT631/NT631C. In this case, it is convenient to use serial port A of the NT631/NT631C. +5 V is not output from serial port B.
Page 44: Preparations At The Nt631/Nt631C
Section 2-2 Preparations at the NT631/NT631C Before starting operation, the names and functions of the parts of the NT631/NT631C are described here as a confirmation. A method of hardware set- tings is also described. 2-2-1 Names and Functions of Parts...
Page 45 Preparations at the NT631/NT631C Rear ViewNotice Reset switch (inside the cover) Used to initializes all the statuses of the NT631/NT631C. However, registered data such as screen data, and memory switch settings, retain their statuses before initialization. Serial port B terminal block...
Page 46: Hardware Settings And Connections
Hardware Settings and Connections This section describes the settings of the NT631/NT631C and methods for connection to peripheral devices. For details on the method for connection to the host, refer Section 4 “Connecting to the Host from the RS–232C Port” or Section 5 “Connecting to the Host from the RS-422A/485 Port”.
Page 47: Installation
- Potential exposure to radioactivity 3-1-2 Installation in the Operation Panel The NT631/NT631C is mounted in an operation panel by embedding it in the pan- Use the panel fittings and tool (Philips screwdriver) included in the product pack- age and follow the procedure below.
Page 48: Power Supply Connection
2.When installing NT631-ST211(B) on the ultimate system, the rear of the -EV1 NT631 must be placed within an enclosure to restrict the operators’ use only to the front panel. - When using NT631-ST211(B) , warm-up time of the power supply must be -EV1 200 ms or less.
Page 49: Grounding
The NT631/NT631C has a functional ground terminal ( Carry out wiring under the following conditions. (1) In cases where the distance between the NT631/NT631C is small and it is assumed that there is no potential difference between grounds, ground as shown in Fig.
Page 50: Connecting To The Support Tool
Connecting to the Support Tool Connecting to the Support Tool In order to install the system program in the NT631/NT631C, or to transmit screen data created with the Support Tool to the NT631/NT631C, the NT631/NT631C must be connected to a personal computer with an RS-232C cable.
Page 51: Connecting A Printer
The length of the cable should not exceed 1.5 m. Reference If the connector cable is connected or disconnected while the power to the printer is on, the NT631/NT631C may malfunction. Always turn off the power to the print- er before connecting or disconnecting the cable. EPSON...
Page 52: Connecting A Bar Code Reader
Make sure that the power supply to the bar code reader and the power supply to the PT are both OFF before connecting or disconnecting the cable. 3-4-1 Connection Method Connect the bar code reader to serial port A of the NT631/NT631C, as shown in the figure below. NT631/NT631C Bar code reader...
Page 53: Setting A Bar Code Reader
Make the settings shown in the table below at the bar code reader. Make sure that the communications speed, parity, stop bit, and data bit settings match the com- munication settings made at the NT631/NT631C. For details on the setting meth- od, refer to the instruction manual for the bar code reader used.
Page 54: Data Format
During bar code reading, the NT631/NT631C performs RS/CS control. When the “Input Method” setting of the NT631/NT631C is set to “Auto”, the RS signal is turned OFF, prohibiting the next input, until the read data has been notified to the host.
Page 55: Using A Memory Unit (Nt631/Nt631C With V1)
After mounting a memory unit, be sure to tighten its two screws. - During data transmission, do not turn off the power supply to the NT631/NT631C or reset it. - Do not touch the PCB (printed circuit board) with bare hands.
Page 56: Installation Method
Using a Memory Unit (NT631/NT631Cwith V1) Section 3-5 Reference - When a memory unit is mounted, the NT631/NT631C cannot be set to the oper- ating status. On completion of data transmission with a memory unit, always disconnect the memory unit from the NT631/NT631C before starting NT631/NT631C operation.
Page 57: Method Of Use
DIP switches that are set at startup. Factory setting is turned all to off. Notice - Always confirm that the power to the NT631/NT631C is off before setting the DIP switches. - Do not touch the PCB (printed circuit board) directly with bare hands.
Page 58 Use the following procedure to write the screen data in the NT631/NT631C to the memory unit by automatic transmission. (1) Check that the power supply to the NT631/NT631C is OFF, then set the DIP switches of the memory unit as follows after installing memory unit to NT631/NT631C.
Page 59 NT631/NT631C, this mode becomes con- venient. Reference When data is written to the NT631/NT631C, the data that has been stored up until that point is lost. When the system program is changed, the operation of NT631/NT631C also changes.
Page 60 Bank 0: other than system program, Bank 1: system program If the combination is not as listed above, a data transmitting error occurs. - When writing the system program into the NT631/NT631C, the type of system program inside memory unit and the type of PT unit must be corresponding.
Page 61 NT631/NT631C. Transmission can be exe- cuted while checking the settings. Reference When data is written to the NT631/NT631C or memory unit, the data that has been stored up until that point is lost. S Method of execution Use the following procedure to write screen data using manual transmission.
Page 62 Bank 0: system program, Bank 1: other than system program Bank 0: other than system program, Bank 1: system program - When writing the system program into the NT631/NT631C, the type of system program inside memory unit and the type of PT unit must be corresponding.
Page 63 NT631/NT631C power back ON. Errors When Using a Memory Unit If an error occurs when using the memory unit, the NT631/NT631C operates as follows. S The details of the error and remedial action are displayed on the screen.
Page 64 Section 3-5 Using a Memory Unit (NT631/NT631C with V1) When an error occurs, take remedial action by referring to the table below. Error Probable Cause Remedial Action Mode setting error DIP switches SW1-1 to Turn the NT631/NT631C power SW1-3 are all OFF, or OFF, set the memory unit DIP more than one is ON.
Page 65: Using A Memory Unit (Nt631/Nt631C Without V1)
- Do not touch the PCB (printed circuit board) with bare hands. Reference - When a memory unit is mounted, the NT631/NT631C cannot be set to the oper- ating status. On completion of data transmission with a memory unit, always disconnect the memory unit from the NT631/NT631C before starting NT631/NT631C operation.
Page 66: Installation Method
DIP switches that are set at startup. Factory setting is turned all to off. Notice - Always confirm that the power to the NT631/NT631C is off before setting the DIP switches. - Do not touch the PCB (printed circuit board) directly with bare hands.
Page 67 Use the following procedure to write the screen data in the NT631/NT631C to the memory unit by automatic transmission. (1) Check that the power supply to the NT631/NT631C is OFF, then set the DIP switches of the memory unit as follows after installing the memory unit in NT631/NT631C.
Page 68 When transmitting the same system program or screen data to multiple NT631/NT631C, this mode becomes convenient. Reference When data is written to the NT631/NT631C, the data that has been stored up until that point is lost. S Method of execution Use the following procedure to write the screen data in the memory unit to the NT631/NT631C by automatic transmission.
Page 69 NT631/NT631C. Transmission can be exe- cuted while checking the settings. Reference When data is written to the NT631/NT631C or memory unit, the data that has been stored up until that point is lost. S Method of execution Use the following procedure to read and write screen data using manual trans- mission.
Page 70 Using a Memory Unit (NT631/NT631C without V1) Errors When Using a Memory Unit If an error occurs when using the memory unit, the NT631/NT631C operates as follows. S The details of the error and remedial action are displayed on the screen.
Page 71: Connecting To The Host From The Rs-232C Port
SECTION 4 Connecting to the Host from the RS-232C Port This section describes the method for connecting to the host using the RS-232C port of the NT631/NT631C. Connecting to the RS-232C Port at the Host ........
Page 72: Connecting To The Rs-232C Port At The Host
S Direct connection between the RS-232C ports using an RS-232C cable (page 126) This is the easiest connection method. Depending on the host to which the con- nection is to be made, it may be possible to use OMRON cables with connectors. NT631/NT631C Host RS-232C cable (max.
Page 73 The host units that can be connected to the NT631/NT631C by the host link method using the RS-232C ports of both units are indicated in the table below.
Page 74 C200H-CPU01/02/03/1 1/ C200H 21/22/23/31-E C120–LK201-EV1 C1000H C1000H–CPU01-EV1 C2000H C2000H–CPU01–EV1 C200H-CPU01/2/03/1 1/ 21/22/23/31-E C200H C200HS-CPU01/03/21/23/ C200HS 31/33-E C200HE C200HE-CPU11/32/42–E C200HE-Z C200HE-CPU11/32/42-ZE C200H-LK201-EV1 C200HG C200HG-CPU33/43/53/63-E C200HG-Z C200HG-CPU33/43/53/63–ZE C200HX C200HX-CPU34/44/54/64-E C200HX–Z C200HX–CPU34/44/54/64 65/85-ZE C200HS-CPU21/23/31/33 C200HS C200HE-CPU42 C200HE-CPU32/42-E C200HW-COM02/04/ C200HE C20HE-CPU42-Z C200HE-CPU32/42-ZE 05/06-EV1 C200HE-Z C200HG-CPU43/63 C200HG–CPU33/43/53/63-E C200HG...
Page 75 Unit # *1 Set the host link communications speed at 9600 bps or 19200 bps with the memory switch at the NT631/NT631C. For details, refer to “Setting the Host Link Method” (page 174). *2 The 1-to-N setting enables BCC (Block Check Character). It is not actually possible to connect more than one NT631/NT631C in a single host link.
Page 76 Section 4-1 Connecting to the RS-232C Port at the Host S Connecting to a C series host link unit C200H/C200HS/C200HE/HG/HX (-ZE) backplate mounted type: C200H-LK201-V1 [Setting the front switches] Set each switch with a flat blade screwdriver so that the values or symbols in the setting value window agree with the following.
Page 77 Section 4-1 Connecting to the RS-232C Port at the Host C1000H(F)/C2000H backplate mounted type: 3G2A5-LK201-EV1 [Setting the front switches] Local Host @ Mode control (key switch) Set this to “host link”. [Setting the rear switches] @ I/O port selection (selector switch) Set this to “RS-232C”.
Page 78 Section 4-1 Connecting to the RS-232C Port at the Host C1000H/C2000H backplate mounted type: C500-LK203 [Setting the rear switches] @ I/O port selection (selector switch) Set this to “RS-232C”. 5V supply @ Unit #, parity, and transfer code (DIP SW1-1 to SW1-7) I/O port RS-422A Set SW1-1 to SW1-7 to “OFF”...
Page 79 Section 4-1 Connecting to the RS-232C Port at the Host C200H/C1000H/C2000H CPU mounting type: 3G2A6-LK201-EV1 [Setting the rear switches] @ Unit #, parity, and transfer code (DIP SW1-1 to SW1-5) Set SW1-1 to SW1-5 to “OFF” (0). * Parity is fixed at Even Parity. Transfer code is fixed at ASCII 7 data bits and 2 stop bits.
Page 80 Level 1, 2, 3 *1 Set the host link communications speed at 9600 bps or 19200 bps with the memory switch at the NT631/NT631C. For details, refer to “Setting the Host Link Method” (page174). *2 The 1-to-N setting enables BCC (Block Check Character). It is not actually possible to connect more than one NT631/NT631C in a single host link.
Page 81 Section 4-1 Connecting to the RS-232C Port at the Host [Setting the front switches] @ Unit # (SW3, SW4) When using communication port 2, set these switches to “0”. Communications port 1 (RS-232C) @ I/O port selection (selector switch) Set this to “RS-232C”. Communications port 2 @ CTS selection (DIP SW2 and SW3) (RS-232C/RS-422A)
Page 82 Section 4-1 Connecting to the RS-232C Port at the Host [Allocation DM area settings for CPU] Settings are written from the peripheral tool (a programming console or CX–Pro- grammer) directly into the allocation DM area (system setting area) of the CPU. After the settings are written, they become effective by turning the power ON, re- starting the unit, restarting the communication port, or execution of the STUP com- mand.
Page 83 Unit # *1 Set the host link communications speed at 9600 bps or 19200 bps with the memory switch at the NT631/NT631C. For details, refer to “Setting the Host Link Method” (page 174). Either set PC system settings directly from a peripheral tool (e.g. SYSMAC support software), or transmit the PC system settings made at a peripheral tool to the CPU.
Page 84 Unit # *1 Set the host link communications speed at 9600 bps or 19200 bps with the memory switch at the NT631/NT631C. For details, refer to “Settings the Host Link Method” (page174). Set the PC system setting area settings directly from a peripheral tool (e.g.
Page 85 Section 4-1 Connecting to the RS-232C Port at the Host When using port A of the communication board of C200HX/HG/HE (-ZE) Word # Writing Value Settings DM6555 0001 Host link mode, no CTS control Communication conditions set by the contents of DM DM6556 0303 Data length 7 bits, 2 stop bits, even parity, communications speed: 9600 bps...
Page 86 Unit No. for the host link *1: Set the host link communications speed at 9600 bps or 19200 bps with the memory switch at the NT631/NT631C. For details, refer to ”Settings the Host Link Method” (page 174). When the communication speed is set to 19200 bps., the PC system settings of the CPU need to be changed.
Page 87 Section 4-1 Connecting to the RS-232C Port at the Host [Setting the front switches] Set the CPU DIP switches to 4 or 5 in accordance with the port NT631/NT631C is connected to. ERR/ALM PRPHL/COMM SYSMAC CS1G PROGRAMMABLE CONTROLLER CPU4 Peripheral port...
Page 88 Check the model and series of the PC against the type of CPU before making the connections. The host units that can be connected to the NT631/NT631C by the NT link (1:1) method using the RS-232C ports of both units are indicated in the table below.
Page 89 Section 4-1 Connecting to the RS-232C Port at the Host S Settings at the host The setting methods for each unit are as follows. S Connecting to a C-series C200HS, C200HX/HG/HE(-ZE), CPM1, CQM1, SRM1 [PC system setting area settings] Write the “PC system setting area” (data memory) settings directly from a pe- ripheral tool (e.g.
Page 90 Section 4-1 Connecting to the RS-232C Port at the Host S Connecting to CVM1/CV series (-EVj) Set the DIP switches on the front panel as follows. I/O port selection (selector switch) Set this to “RS-232C”. DIP switch setting (SW3) Set SW3 to “use NT link” (“ON”, right side).
Page 91 Check the model and series of the PC against the type of CPU or communica- tions board before making the connections. The host units that can be connected to the NT631/NT631C by the NT link (1:N) method using the RS-232C ports of both units are indicated in the table below.
Page 92 CPU. For details on PC system settings, refer to the “SYSMAC CS1 Series Operation Manual” (W339-E1 [Setting the front switches] Set the CPU DIP switch to 4 or 5 in accordance with the port NT631/NT631C is connected to. ERR/ALM PRPHL/COMM...
Page 93 Section 4-1 Connecting to the RS-232C Port at the Host S Connecting to the CS1 series serial communication board INNER board with RS-232C port equipped for CS1 series CPU type : CS1W-SCB41/21 [CPU allocation DM area settings] Setting is written from the peripheral tool (a programming console or CX-Program- mer) directly into the allocation DM area (system setting area) of the CPU.
Page 94 Section 4-1 Connecting to the RS-232C Port at the Host S Connecting to CS1 series serial communication unit A CS1 series backplane mounted type : CS1W-SCU21 [Setting the front switches] Set the unit number of the serial communication unit by using the rotary switch lo- cated on the front panel.
Page 95 For the host (a personal computer, an FA computer, etc.), its setting should be compatible to one of the communication conditions listed in the following table. Set the same communication conditions at the NT631/NT631C by the memory switch. (page 179).
Page 96 Section 4-1 Connecting to the RS-232C Port at the Host 4-1-2 Connecting Directly between RS-232C Ports The method for connection between the RS-232C ports of the NT631/NT631C and the host is described here. Host link unit/CPU NT631/NT631C SYSMAC C-series PC,...
Page 97 XW2Z-200T 9-pin ⇔ 9-pin ⇔ XW2Z-500T When a connection is made to a personal computer at serial port A in the memory link method, OMRON cable with connectors shown below are avail- able. Model Cable Length Connector Specification 9-pin ⇔ 25 pin CV500–CN228...
Page 98 Section 4-1 Connecting to the RS-232C Port at the Host [Serial port A, B] NT631/NT631C PC (host link unit) Abbreviation Shielding wire Abbreviation number number Connector hood RS-232C RS-232C interface interface – – – – – – (9-pin type) –...
Page 99 Section 4-1 Connecting to the RS-232C Port at the Host Wiring for Other Connections Applicable units : CV500-LK201 (communication port 2) CPM1-10CDR-j CPM1-20CDR-j CPM1-30CDR-j CPM1A-10CDj-j CPM1A-20CDj-j CPM1A-30CDj-j CPM1A-40CDj-j CQM1-CPU21-E CQM1-CPU41-EV1 CQM1-CPU42-EV1 CQM1-CPU43-EV1 CQM1-CPU44-EV1 CQM1-CPU45-EV1 CS1G–CPU42–E CS1G–CPU43–E CS1G–CPU44–E CS1G–CPU45–E CS1H–CPU63–E CS1H–CPU64–E CS1H–CPU65–E CS1H–CPU66–E CS1H–CUP67–E...
Page 100 Section 4-1 Connecting to the RS-232C Port at the Host [Serial port A, B] NT631/NT631C PC (Host link unit) Abbreviation Shielding wire Abbreviation number number Connector Connector hood hood – RS-232C interface RS-232C interface – – – – – (9-pin type)
Page 101 ⇔ CV500–CN228 (9–pin 25–pin, 2 m) ⇔ XW2Z–S002 (9–pin 9–pin, 2 m) [Serial port A, B] Prepare the adapter cable while referring to the following diagram. Host side NT631/NT631C Abbreviation Abbreviation Pin number Shielding wire Connector Connector hood hood −...
Page 102: Connecting To The Host From The Rs-422A/485 Port
SECTION 5 Connecting to the Host from the RS-422A/485 Port This section describes the method for connecting to the host using the RS-422A/485 port of the NT631/NT631C. Connecting to the Host’s RS-232C Port ......... . .
Page 103: Connecting To The Host's Rs-232C Port
(max. 500 m) cable (max. 2 m) S Method in which the RS-485 port of the NT631/NT631C and the RS-232C port of the host are connected in a 1:1 connection via an RS-232C/RS-422A convertor unit (page 98). When this method is used, the cable length can be extended up to 500 m. This connection method can be used only with the NT link (1:N) method of type RS-485.
Page 104: The Type Of Host And Settings
Connecting to the Host’s RS-232C Port Section 5-1 S Method in which the RS-485 ports of multiple NT631/NT631Cs and the RS-232C port of the host are connected in a 1:N connection via an RS-232C/RS-422A convertor unit (page 103). This connection method is used with the RS-485 type NT link (1:N) method.
Page 105 Connecting to the Host’s RS-232C Port Section 5-1 Settings at the RS-232C/RS-422A Convertor Unit (NT-AL001) When making a connection between RS-232C and RS-422A/485 ports using an RS-232C/RS-422A convertor unit, set the DIP switches on the NT-AL001 as fol- lows. Example: the terminal resistor is active, RS-422A, NT link (1:N).
Page 106: 1:1 Connection Between Rs-422A/485 At The Nt631/Nt631C And Rs-232C At The Host
RS-232C cable (max. length: 500 m) with connectors RS-422A terminal block 9-pin connector Reference When using RS-485 as a port for the NT631/NT631C, only NT link (1:N) method can be used. Connecting an NT631/NT631C and NT-AL001 (RS-422A) NT631/NT631C Host NT-AL001...
Page 107 In order to avoid an FG ground loop, do not make the connection between the func- tional ground of the NT-AL001 and the shielding. Reference When using RS-485 as a port for the NT631/NT631C, only NT link (1:N) method can be used.
Page 108 Section 5-1 Connecting to the Host’s RS-232C Port Connecting an NT-AL001 and Host NT631/NT631C Host NT-AL001 RS-232C S Wiring when connecting a host link unit (25-pin) Applicable units: C200H-LK201-V1 3G2A5-LK201-EV1 C500-LK203 3G2A6-LK201-EV1 CV500-LK201 (communication port 1) Cables with connectors that can be used: ⇔...
Page 109 Section 5-1 Connecting to the Host’s RS-232C Port S Wiring for Connections other than Memory Link Applicable units: CV500-LK201 (communication port 2) CPM1-10CDR-j CPM1-20CDR-j CPM1-30CDR-j CPM1A-10CDj-j CPM1A-20CDj-j CPM1A-30CDj-j CPM1A-40CDj-j CQM1-CPU21-E CQM1-CPU41-EV1 CQM1-CPU42-EV1 CQM1-CPU43-EV1 CQM1-CPU44-EV1 CQM1-CPU45-EV1 CS1G-CPU42-E CS1G-CPU43-E CS1G-CPU44-E CS1G-CPU45-E CS1H-CPU63-E CS1H-CPU64-E CS1H-CPU65-E CS1H-CPU66-E...
Page 110 Section 5-1 Connecting to the Host’s RS-232C Port NT-AL001 side PC side Pin number Abbreviation Pin number Abbreviation Connector Connector hood hood − − RS-232C RS-232C connector connector (+5V) − − − − Shielding wire (9-pin type) (9-pin type) When there is no +5 V output at the PC side When using host link or NT link (1:1) When there is +5 V output at the PC side When using NT link (1:N)
Page 111: 1:N Connection Between Rs-422A/485 At The Nt631/Nt631C And Rs-232C At The Host
1:N Connection between RS-422A/485 at the NT631/NT631C and RS-232C at the Host The connection method in which the RS-422A/485 ports of multiple NT631/ NT631Cs are connected to the RS-232C port of one host in a 1:N connection is described here.
Page 112 Section 5-1 Connecting to the Host’s RS-232C Port Connecting an NT631/NT631C and NT-AL001 (RS-422A) The relay terminal board is not included in the figure below. Insert a relay terminal board so as to achieve the wiring configuration indicated below. NT631/NT631C...
Page 113 Section 5-1 Connecting to the Host’s RS-232C Port Connecting an NT631/NT631C and NT-AL001 (RS-485) The relay terminal board is not included in the figure below. Insert a relay terminal board so as to achieve the wiring configuration indicated below. NT631/NT631C...
Page 114 Shielding ground ground wire Short TRM and RDA terminals of the NT631/NT631C at the end of the RS-422A cable ( marked in the above figure) using the short-circuit tool supplied with the NT631/NT631C. In order to avoid an FG ground loop, make the connection between the connector...
Page 115 Shielding wire Short TRM and RDA terminals of the NT631/NT631C at the end of the RS-485 cable marked in the above figure) using the short-circuit tool supplied with the NT631/NT631C. In order to avoid an FG ground loop, make the connection between the connector...
Page 116 Section 5-1 Connecting to the Host’s RS-232C Port Connecting an NT-AL001 and Host NT631/NT631C Host NT-AL001 RS-232C S Wiring when connecting a CS1 series CS1G/H serial communication board, C series C200HX/HG/HE (–Z) communication board. Applicable units: CS1G-CPU42-E CS1G-CPU43-E CS1G-CPU44-E CS1G-CPU45-E...
Page 117: Recommended Connectors, Cables, And Crimp Terminals
Multi-core shielded cable CO-MA-VV-SB 5P 28AWG Made by Hitachi, Ltd. S Cables with connectors made by OMRON When connecting an NT-AL001 and a PC, use the OMRON cables with connec- tors indicated in the table below. Model Cable Length Connector Specification 9-pin ⇔...
Page 118 Y1.25-3.5L Morex Inc. (0.3 to 0.75 mm (fork type) The terminal screws of the NT631/NT631C are M3.5 specification. When wir- ing, use crimp terminals for M3.5 use. Tighten terminal screws with a tightening torque of 0.8 N@m. Notice Always use crimp terminals for wiring.
Page 119: Setting The Terminal Resistance For Rs-422A/485 Communications
5-1-5 Setting the Terminal Resistance for RS–422A/485 Communica- tions The serial port B connector of the NT631/NT631C has a terminal resistance set- ting terminal (TRM). In RS-422A/485 communications, a terminal resistor must be set at the device at the end of the communication cable, but not at any other device.
Page 120: Connecting To The Host's Rs-422A/485 Port
RS-422 unit). When making a connection to a host other than OMRON PCs, refer to the “ PC Connection” (V042-E1-j). S Method in which the RS-422A ports of the NT631/NT631C and host are con- nected directly by an RS-422A cable (page 132).
Page 121: Host Types And Settings
Host Types and Settings The types of host that have an RS-422A port and can be connected to the RS-422A/485 port of the NT631/NT631C, and the settings to be made at the host, are described here. When Using the Host Link Method...
Page 122 Section 5-2 Connecting to the Host’s RS-422A/485 Port Units with Built-in Host Link Function CPUs Connectable with CPUs Connectable with PC Series Connectable to Host Link Units or Expansion Host Link Unit / Communication Board Communication Board CS1G-CPU42/43/44/45-E CS1G CS1 series CS1W-SCB41-E CS1H-CPU63/64/65/66/67-E CS1H...
Page 123 Section 5-2 Connecting to the Host’s RS-422A/485 Port The host link method cannot be used when an NT631/NT631C is connected using RS-485. To use the host link method, connect by RS-422A. S Settings at the host When using the RS-422A type host link method, the settings shown below must be made at the host (depending on the unit, some of these settings may not be necessary, or settings not shown here may be necessary).
Page 124 Section 5-2 Connecting to the Host’s RS-422A/485 Port S Connecting to a C series host link unit C200H/C200HS/C200HE(-ZE)/C200HG(-ZE)/C200HX(-ZE) backplate mount- ing type: C200H-LK201-V1 [Setting the front switches] Set each switch with a flat blade screwdriver so that the values or symbols in the setting value window agree with the following: LK201 ERROR...
Page 125 Section 5-2 Connecting to the Host’s RS-422A/485 Port C1000H/C2000H rack-mounting type: 3G2A5-LK201-EV1 [Setting the front switches] Mode selector Host Local @ Mode selector (key switch) Set this to “Host link”. [Setting the rear switches] @ I/O port selection (selector switch) Set this to “RS-422A”.
Page 126 Section 5-2 Connecting to the Host’s RS-422A/485 Port C1000H/C2000H rack-mounting type: C500-LK203 [Setting the rear switches] @ I/O port selection (selector switch) Set this to “RS-422A”. 5V supply @ Unit #, parity, and transfer code I/O port (DIP SW1-1 to SW1-7) RS-422A RS-232C Set SW1-1 to SW1-7 to “OFF”...
Page 127 Section 5-2 Connecting to the Host’s RS-422A/485 Port C200H/C1000H/C2000H CPU mounting type: 3G2A6-LK202-EV1 [Setting the rear switches] @ Unit #, parity, and transfer code (DIP SW1-1 to SW1-5) Set SW1-1 to SW1-5 to “OFF” (0). * Parity is fixed at Even Parity. Transfer code is fixed at ASCII 7 data bits and 2 stop bits.
Page 128 “Setting the Host Link Method” (page 173). *2 The 1-to-N setting enables BCC (Block Check Character). It is not actually possible to connect more than one NT631/NT631C in a single host link. Set the CPU bus unit settings directly from a peripheral tool (e.g. SYSMAC sup- port software).
Page 129 Section 5-2 Connecting to the Host’s RS-422A/485 Port [Setting the front switches] @ Unit # (SW3, SW4) Set these switches to “0”. Communications port 1 (RS-232C) Communications port 2 (RS-232C/RS-422A) I/O port selector switch @ I/O port selection (selector switch) RS-232C Set this to “RS-422A”.
Page 130 Unit # *1 Set the host link communications speed at 9600 bps or 19200 bps with the “Comm. Speed” memory switch at the NT631/NT631C. For details, refer to “Setting the Host Link Method” (page 173). Either set PC system settings directly from a peripheral tool (e.g. SYSMAC sup- port software), or transmit the PC system settings made at a peripheral tool to the CPU.
Page 131 Section 5-2 Connecting to the Host’s RS-422A/485 Port [Setting the front switches] @ Host link communication method selection (selector switch) Set this to “RS-422A”. @ Communication type setting (DIP SW3) Set SW3 to “OFF”. (for “host link” communication) @ Host link default value settings (DIP SW4) To effect the existing DIP switch settings, I/O port selector switch...
Page 132 Unit # *1 Set the host link communications speed at 9600 bps or 19200 bps with the “Comm. Speed” at the NT631/NT631C. For details, refer to “Setting the Host Link Method” (page 173). Set the PC system setting area settings directly from a peripheral tool (e.g. SYS- MAC support software).
Page 133 Section 5-2 Connecting to the Host’s RS-422A/485 Port [Setting the DIP switches on the front of a C200HX/HG/HE(-ZE)] When using a C200HX/HG/HE(-ZE) , the DIP switches on the front panel must be set as shown below in order to make the settings in the PC system setting area (data memory) effective.
Page 134 Check the model and series of the PC against the type of CPU before making the connections. The host units that can be connected to the RS-422A port of the NT631/NT631C by the RS-422A type NT link (1:1) method are indicated in the table below.
Page 135 Section 5-2 Connecting to the Host’s RS-422A/485 Port S Settings at the host The setting methods for each type of unit are described in the following. - Connecting to a CVM1/CV-series (-EVj) CPUs @ CV500-CPU01-EV1/CV1000-CPU01-EV1/CV2000-CPU01-EV1 @ CVM1-CPU01-EV2/CVM1-CPU11-EV2/CVM1-CPU21-EV2 [PC system settings] When connecting to the CVM1/CV series CPU by the NT link (1:1) method, no particular settings are required at the PC system settings.
Page 136 Section 5-2 Connecting to the Host’s RS-422A/485 Port - Connecting to a C-series C200HX/HG/HE(-ZE) [PC system setting area settings] Write the PC system setting area (data memory) settings directly from a pe- ripheral tool (e.g. SYSMAC support software) in accordance with the host model.
Page 137 Check the model and series of the PC against the type of CPU or communica- tions board before making the connections. The host units that can be connected to the RS-232C port of the NT631/NT631C by the RS-422A type NT link (1:N) function via a convertor are indicated in the table below.
Page 138 Connecting to the Host’s RS-422A/485 Port Section 5-2 Connection to Word # Writing Value Setting Use NT link (1:N) Communication board j = highest unit number of the DM6555 5j00 Port A connected PTs (1 to 7) When using C200HE(-ZE), the range for PT unit numbers is 1 to 3. Reference There are no communication boards for which port B is the RS-422A/485 port.
Page 139 For the host (a personal computer, an FA computer, etc.), its setting should be compatible to one of the communication conditions listed in the following table. Set the same communication conditions at the NT631/NT631C by the memory switch. (page 179).
Page 140: Direct Connection Between Rs-422A Ports At Both Units
Section 5-2 Connecting to the Host’s RS-422A/485 Port 5-2-2 Direct Connection between RS-422A Ports at Both Units The connection method in which the RS-422A ports of an NT631/NT631C and a host are connected is described here. Host link/CPU/ Communication unit...
Page 141 SDB (+) RDB (+) RSA (−) RDA (−) RSB (+) (9-pin type) Functional ground In order to avoid an FG ground loop, do not connect the functional ground of the NT631/NT631C to the shielding of the RS-422A cable.
Page 142 − RSA (−) RSB (+) RDA (−) Functional − ground RDB (+) − (9-pin type) In order to avoid an FG ground loop, do not connect the functional ground of the NT631/NT631C to the shielding of the RS-422A cable.
Page 143 SDB (+) interface RSA (−) RSB (+) RDA (−) Functional − ground RDB (+) − (9-pin type) In order to avoid an FG ground loop, do not connect the functional ground of the NT631/NT631C to the shielding of the RS-422A cable.
Page 144 SDA (−) interface SDB (+) RDA (−) RSA (−) RSB (+) RDB (+) Functional ground In order to avoid an FG ground loop, do not connect the functional ground of the NT631/NT631C to the shielding of the RS-422A cable.
Page 145: Direct Connection Between Rs-485 Ports At Both Units
Connecting to the Host’s RS-422A/485 Port Section 5-2 5-2-3 Direct Connection between RS-485 Ports at Both Units The connection method in which the RS-485 ports of an NT631/NT631C and a host are connected is described here. NT631/NT631C CS1G/H C200HX/HG/HE(-ZE) Serial port B...
Page 146: 1:N Connection Among Rs-422A Ports
In order to avoid an FG ground loop, do not connect the functional ground of the NT631/NT631C to the shielding of the RS-422A cable. 5-2-4 1:N Connection among RS-422A Ports The connection method in which the RS-422A ports of multiple NT631/NT631Cs and one host are connected in a 1:N connection is described here. CS1G/H C200HX/HG/HE(-ZE)
Page 147 Functional ground ground Shielding wire Short TRM and RDA terminals of the NT631/NT631C at the end of the RS-422A cable ( marked in the above figure) using the short-circuit tool supplied with the NT631/NT631C. In order to avoid an FG ground loop, connect the functional ground of only one of...
Page 148 RSA (−) − RSB (+) RDA (−) Functional − ground RDB (+) − Next PT (9-pin type) In order to avoid an FG ground loop, do not connect the functional ground of the NT631/NT631C to the shielding of the RS-422A cable.
Page 149: 1:N Connection Among Rs-485 Ports
Connecting to the Host’s RS-422A/485 Port Section 5-2 5-2-5 1:N Connection among RS-485 Ports The connection method in which the RS-485 ports of multiple NT631/NT631Cs and one host are connected in a 1:N connection is described here. CS1G/H C200HX/HG/HE(-ZE) 9-pin connector RS-485 cables (max.
Page 150 Shielding wire Short TRM and RDA terminals of the NT631/NT631C at the end of the RS-485 cable marked in the above figure) using the short-circuit tool supplied with the NT631/NT631C. In order to avoid an FG ground loop, do not connect the functional ground of the...
Page 151 RSA (−) RSB (+) RDA (−) Functional − ground RDB (+) − Next PT (9-pin type) In order to avoid an FG ground loop, do not connect the functional ground of the NT631/NT631C to the shielding of the RS-485A cable.
Page 152: Recommended Connectors, Cables And Crimp Terminals
(fork type) *1 *1 Crimp terminals of common use for M3 and M3.5 The terminal screws of the NT631/NT631C are M3.5 specification. When wir- ing, use crimp terminals for M3.5 use. Tighten terminal screws with a tightening torque of 0.8 N The terminal screws of the RS-422A adaptor (CPM1-CIF11) are M3 specifica- tion.
Page 153: Setting The Terminal Resistance For Rs-422A/485 Communications
When carrying out RS-422A/485 communications using serial port B, short be- tween terminals at the NT631/NT631C at the end of the RS-422A/485 cable. Leave these terminals open at NT631/NT631C units other than the one at the end of the cable.
Page 154: System Menu Operation
SECTION 6 System Menu Operation This section describes the operation of the System Menu, focusing on the procedure to start up the NT631/NT631C. Functions which are convenient when using the NT631/NT631C and those that are useful for system maintenance are also explained here.
Page 155 6-11 System Maintenance ............6-11-1 I/O Settings .
Page 157: System Menu Operation Flow
[Create the Screen Data] Create the data to be displayed on the NT631/NT631C by using the Support Tool. For details on creating screen data, refer to the NT-series Support Tool Ver. 3.0 for Windows95 Operation Manual (V053-E1-j).
Page 158: Starting The Nt631/Nt631C
[Start of Communication with the Host] Communication with the host starts in accordance with the communication meth- od set in the system memory of the NT631/NT631C. During the interval until com- munication is established, the “system initialization screen” (screen No. 9000) is displayed.
Page 159: Operation Modes And The System Menu
“Expansion” modes. These modes are selected from the System Menu. In addition, the NT631/NT631C also features the “System Installer” mode which is used specifically for installing the system program. The System Installer mode is selected by operation at the panel when the NT631/NT631C power is switched ON.
Page 160 Transmit Mode Display the Transmit Mode screen to allow transmission for screen data between the Support Tool and the NT631/NT631C. For details on transmission of screen data, refer to 6-6 “Transmit- ting the Screen Data” (page 169). Maintenance Mode Display the Maintenance Mode menu to allow system mainte- nance of the NT631/NT631C, and various NT631/NT631C set- tings.
Page 161: Menu Tree
Operation Modes and the System Menu 6-3-2 Menu Tree The System Menu allows the various functions of the NT631/NT631C to be exe- cuted by using touch switches displayed on the touch panel. The menu tree, start- ing from the System Menu, is shown below.
Page 162: Operations With The System Menu
Reference With the NT631/NT631C, the System Menu can be displayed even if the screen has touch switches registered at all four corners. S Pressing a touch switch that displays the System Menu There is a “control key”...
Page 163 Operation Modes and the System Menu Section 6-3 Calling the System Installer Mode If the NT631/NT631C has no system program installed, or if the system program is destroyed, the System Installer mode is automatically established when the power is switched ON.
Page 164: Memory Initialization
System Installer mode, memory initialization is not possible. 6-4-1 Clearing Screen Data Use this function if the screen data has been corrupted and the NT631/NT631C cannot be started up correctly. It clears (initializes) only the screen data: the memory switch settings and display history/alarm history record data are retained.
Page 165 The screen data is cleared. During clear- ance, the message “Erasing Now...” is dis- played. S If “No” is selected, the NT631/NT631C returns to the “MEMORY INIT. MENU” screen without clearing the screen data. On completion of screen data clearance, the NT631/NT631C returns to the “MEMORY INIT.
Page 166: Initializing Display History Record Data
Reference The NT631/NT631C also allows the display history record data to be initialized by controlling the PT status control area from the host. For details, refer to “Display history initialization (bit 11)”...
Page 167: Initializing Alarm History Record Data
The display history record data is initialized. During initialization, the message “Initializing” is displayed. S If “No” is selected, the NT631/NT631C returns to the “MEMORY INIT. MENU” screen without initializing the display history record data. On completion of display history record data initialization, the message “Finished”...
Page 168 During initialization, the message “Initializing” is displayed. S If “No” is selected, the NT631/NT631C returns to the “MEMORY INIT. MENU” screen without initializing the alarm history record data. On completion of alarm history record data initialization, the message “Finished” is...
Page 169: Initializing The Memory Tables
Reference - If “OFF” is set for the “Resume Function” memory switch, the memory tables can be initialized just by switching the NT631/NT631C power off and back on again, or by resetting the NT631/NT631C (page 199). - The bit memory table merely reflects the statuses of bits at the host and there- fore cannot be initialized.
Page 170: Initializing The Memory Switches
The memory tables are initialized. During init- ialization, the message “Initializing” is dis- played. S If “No” is selected, the NT631/NT631C returns to the “MEMORY INIT. MENU” screen without initializing the memory tables. On completion of memory table initialization, the message “Finished” is displayed and the NT631/NT631C returns to the “MEMORY INIT.
Page 171 The memory tables are initialized. During init- ialization, the message “Initializing” is dis- played. S If “No” is selected, the NT631/NT631C returns to the “MEMORY INIT. MENU” screen without initializing the memory switches. On completion of memory switch initialization, the message “Finished” is dis- played and the NT631/NT631C returns to the “MEMORY INIT.
Page 172: Operations In The System Installer Mode
Section 6-5 Operations in the System Installer Mode Operations in the System Installer Mode The following functions can be executed in the System Installer mode: S Setting the display language (see below) S Clearing/installing the system program (page 165) S Disabling/enabling display of the System Menu (changing the system settings) (page 166) S Disabling/enabling writing to the screen data memory (changing the system set- tings) (page 166)
Page 173: Clearing/Installing The System Program
- When the system program is cleared by mistake, it becomes impossible to use the NT631/NT631C at all. Check that the system installer is installed at the Sup- port Tool side before deleting the program. However, note that the registered screen data and memory switch settings are retained.
Page 174: Changing The System Settings
System Menu is displayed. Reference If the new system program is not downloaded successfully after deleting a system program, it is not possible to use the NT631/NT631C at all. After deleting the sys- tem program, be sure to download a new one. 6-5-3...
Page 175 NT631/NT631C while the screen is dis- played. S If “Cancel” is selected, the NT631/NT631C returns to the System Installer mode menu without changing the settings. The settings remain as they were before the operation was started. S If writing of the settings fails, a screen asking whether you wish to try again is displayed.
Page 176: Clearing Screen Data
6-5-4 Clearing Screen Data If the screen data has been corrupted and the NT631/NT631C cannot be started normally, use this function to clear the screen data. Note that only the screen data is cleared (initialized), and the memory switch set- tings and the display history/alarm history record data are retained.
Page 177: Transmitting The Screen Data
It is possible to transmit the screen data (data for all the screens) in “file units”, or to transmit individual data or the data of individual screens in “data units”. When data is transmitted in “file units”, all of the screen data in the NT631/NT631C is cleared and then the new data is transmitted.
Page 178 NT631/NT631C returns to the Transmit mode. If the screen data cannot be successfully transmitted from the Support Tool, use the communication check functions of the NT631/NT631C to check if communica- tion between the NT631/NT631C is normal or not (page 231).
Page 179 S The cable connecting the NT631/NT631C to the personal computer on which the Support Tool is running is disconnected or has a broken wire. S The “Quit” touch switch on the NT631/NT631C screen is pressed to end screen data transmission.
Page 180: Setting The Conditions For Communications With The Host By Using The Memory Switches
S NT link (1:N) method S Mitsubishi FX method The NT631/NT631C has the following two ports, either of which can be used for communications with the host, depending on the requirements. S Serial port A (exclusively for RS-232C, 9-pin connector)
Page 181: About Communication Conditions
Setting the Conditions for Communications with the Host by Using the Memory Switches 6-7-1 About Communication Conditions Items Set for Communication Conditions The following settings are made for the communication conditions for communica- tion between the NT631/NT631C and the host. S Port communication method/communication type settings Setting Item Function Setting Options Page Comm.
Page 182: Setting The Host Link Method
Possible Combinations of Communication Method Settings The combinations of communication methods that can be set with the NT631/NT631C are indicated in the table below. Combinations other than these listed below cannot be set (when using a system for multi-venders, refer to the “PC Connection Operation Manual”...
Page 183 Section 6-7 Setting the Conditions for Communications with the Host by Using the Memory Switches Display the fourth memory switch screen by pressing the [ ] (next screen) or [ ] (previous screen) touch switch. Press the touch switch corresponding to the port at which the host link method is to be set (“Comm.
Page 184: Setting The Nt Link (1:1) Method
[ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 185: Setting The Nt Link (1:N) Method
[ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 186 Section 6-7 Setting the Conditions for Communications with the Host by Using the Memory Switches Display the fourth memory switch screen by pressing the [ ] (next screen) or [ ] (previous screen) touch switch. Press the touch switch corresponding to the port at which the NT link (1:N) method is to be set (“Comm.
Page 187: Setting The Memory Link Method
[ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 188 Section 6-7 Setting the Conditions for Communications with the Host by Using the Memory Switches Display the fourth memory switch screen by pressing the [ ] (next screen) or [ ] (previous screen) touch switch. Press the touch switch corresponding to the port at which the memory link method is to be set (“Comm.
Page 189 [ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 190: Setting The Communication Type For Serial Port B
Section 6-7 Setting the Conditions for Communications with the Host by Using the Memory Switches 6-7-6 Setting the Communication Type for Serial Port B Set the communication type (RS-232C or RS-422A) for serial port B by following the operation from the System Menu shown below. Select “Maintenance Mode”.
Page 191 [ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 192: Starting Operation
Starting Operation Starting Operation After completing screen data transmission and setting the communication condi- tions, connect the NT631/NT631C to the host and start operation. Notice Check the operation of all screen data and host programs carefully before using them. If incorrect, the system may operate unpredictably.
Page 193 (e.g. SYSMAC sup- port software). If the results of operations at the NT631/NT631C are not sent to the host correct- ly, check the setting of the display elements. For details on setting display ele-...
Page 194: Various System Settings
Since the memory switch settings are backed up to the flash memory by the bat- tery in the NT631/NT631C, they are not cleared when the power is switched OFF. 6-9-1 Memory Switch Setting Screens There are four memory switch setting screens.
Page 195: Setting The "Start-Up Wait Time
6-9-2 Setting the “Start-up Wait Time” The “Start-up Wait Time” is the time lapse until the NT631/NT631C switches to the RUN mode after its power has been switched ON or after it has been reset. Set this item if it takes some time for the host to start operation. Nothing is displayed during the “Start-up Wait Time”.
Page 196: Setting The "Key Press Sound
[ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 197: Setting The "Buzzer Sound
6-9-4 Setting the “Buzzer Sound” The NT631/NT631C has a function for sounding a buzzer in response to an in- struction from the host, or when an error occurs. It is possible to set whether or not the buzzer actually sounds with the memory switches.
Page 198 [ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 199: Setting The "Printer Controller
6-9-5 Setting the “Printer Controller” The NT631/NT631C has a function for printing out data at a printer connected to it in response to an instruction from the host or operation at the NT631/NT631C. Three types of printer can be connected to the NT631/NT631C: select the type used with this memory switch setting.
Page 200: Setting The "Print Method" (Nt631C Only)
6-9-6 Setting the “Print Method” (NT631C Only) The NT631/NT631C has a function for printing out data at a printer connected to it in response to an instruction from the host or operation at the NT631/NT631C. When using the NT631C, the currently displayed screen image or other data can be printed out in color.
Page 201 [ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 202: Setting "Screen Saver Movement
6-9-7 Setting “Screen Saver Movement” The NT631/NT631C has a function to prevent the formation of an afterimage by turning off the screen display if no operation is performed for a certain period of time, and then displaying character strings at random positions and in random col- ors (the colors only change for the NT631C).
Page 203 [ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 204: Setting The Screen Saver Start-Up Time
6-9-8 Setting the Screen Saver Start-up Time The NT631/NT631C has a function to maximize the service life of the backlight and prevent the formation of an afterimage by turning off the screen display and the backlight if no operation is performed for a certain period of time.
Page 205: Setting The History Display Method
[ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 206 [ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 207: Setting The Resume Function
Setting the Resume Function The NT631/NT631C has a function to keep the contents of the memory tables even when the power to the NT631/NT631C is OFF and write back them to the host when the power is turned ON. If the resume function is OFF, the memory tables are initialized to these initial val- ues on switching to the RUN mode.
Page 208: Setting The Automatic Reset Function
[ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 209 Reference - If a communication error occurs when “OFF” is set for “Comm. Auto-return”, the NT631/NT631C makes the number of attempts at communication with the host specified by the setting for the “Retry Counts” touch switch (page 203). If com- munication cannot be re-established in any of these attempts, an error screen is displayed.
Page 210: Setting The Time-Out Interval
[ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 211: Setting The Retry Count
[ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 212 [ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 213: 6-10 Setting The Bar Code Reader Input Function
Section 6-10 6-10 Setting the Bar Code Reader Input Function The NT631/NT631C has a bar code reader input function which allows a bar code reader to be connected and bar code data to read as character strings into charac- ter string input fields.
Page 214 Section 6-10 Setting the Bar Code Reader Input Function Select “Memory Switch”. Press [ ] (next screen) or [ ] (previous screen) to display the fourth memory switch setting screen. Press “Comm. A Method” to select “Bar-Code Reader”. The setting option changes each time the touch switch is pressed.
Page 215 [ ] (previous screen) touch switch, then make the setting. S To confirm the settings and quit the memory switch setting screen, press the “Quit” touch switch. The settings made last will be set and the NT631/NT631C will return to the “MAINTENANCE MODE MENU” screen.
Page 216: System Maintenance
“CONTRAST ADJUST” screen enables you to make the adjustment while actually checking the contrast on the screen. Once the contrast has been set, it remains in effect even if the power is turned OFF or the NT631/NT631C is reset (and even if the voltage of the built-in battery becomes low).
Page 217 [Y]: Increase 1 step [B]: Decrease 1 step ]: Decrease 10 steps Press “Quit”. The contrast is set and the NT631/NT631C returns to the “I/O SETTINGS MENU” screen. Backlight Brightness Adjustment (for NT631C-ST141j-EV1 only) The NT631C–ST141j–EV1 allows the brightness of the backlight to be adjusted in 3 steps.
Page 218 Select “I/O Settings”. Select “Brightness Adjust”. Adjust the contrast with the “High”, “Middle”, and “Low” touch switches in the left half of the screen. Press “Quit”. The contrast is set and the NT631/NT631C returns to the “I/O SETTINGS MENU” screen.
Page 219: Displaying/Setting The Calendar And Clock
- No clock data is set on shipment from the factory. - The clock data is backed up by the built-in battery of the NT631/NT631C. If the battery voltage becomes low, the clock data cannot be retained when the power to the NT631/NT631C is turned OFF or the NT631/NT631C is reset and the clock function will not operate correctly.
Page 220 Press “Quit”. The clock data is set and the NT631/NT631C returns to the date and time display. S Pressing “Abort” causes the NT631/NT631C to return to the date and time dis- play without executing setting (with the previous settings still effective).
Page 221: Checking The Pt Setting Status
System Maintenance 6-11-3 Checking the PT Setting Status The direct connection settings of the NT631/NT631C screen data, and the set- tings for serial port A and serial port B, can be checked. Screen Configuration and Display Contents There are the following three PT setting status screens.
Page 222 Menu shown below. Select “Maintenance Mode”. Select “PT Settings”. Switch the screen as required by pressing the [ ] (next screen) or [ ] (previous screen) touch switch. Press “Quit”. The NT631/NT631C returns to the “MAINTE- NANCE MODE MENU” screen.
Page 223: Displaying And Printing The Display History Record
“sort by frequency” (order of number of times displayed). Reference - With the NT631/NT631C, the record data can also be displayed by calling screen No. 9001 (sort by occurrence) or screen No. 9002 (sort by frequency) during the RUN mode.
Page 224 If required, press “Prt.” to print the display his- tory record data. Press “Quit”. The NT631/NT631C returns to the “DISPLAY HISTORY MENU” screen. S Example print-out All of the recorded data is printed out in the same order as on the currently dis- played screen.
Page 225: Displaying And Printing The Alarm History Record
“sort by frequency” (order of number of times the bits have come “ON”). Reference - With the NT631/NT631C, the record data can also be displayed by registering an “alarm history” display element on the screen. - For details on the alarm history record function, refer to 7-15-2 “Alarm History Record Function”...
Page 226 If required, press “Prt.” to print the display his- tory record data. Press “Quit”. The NT631/NT631C returns to the “ALARM HISTORY MENU” screen. S Example print-out All of the recorded data is printed out in the same order as on the currently dis- played screen.
Page 227: Checking Screen Data
Section 6-11 6-11-6 Checking Screen Data The NT631/NT631C allows the registered screens (Nos. 1 to 3999) to be dis- played and checked by operation from the System Menu. Reference - Window screens cannot be displayed by operation from the System Menu.
Page 228 Section 6-11 System Maintenance Displaying the “SCREEN DATA CHECK” Screen Display the “SCREEN DATA CHECK” screen by following the menu operation from the System Menu shown below. Select “Maintenance Mode”. Select “Screen Data Disp.” Specify the screen to be displayed in the input field in the middle of the screen.
Page 229 Section 6-11 System Maintenance Press the touch switches to specify the dis- play method in each case. The setting option changes each time a touch switch is pressed. Press “Quit” to return to the screen number selection screen. Press “Disp”. Touching the top or bottom of the screen BOILER OPERATION changes the way the display elements over-...
Page 230: Device Check
To end the operation, press “Quit” on the screen number selection screen. The NT631/NT631C returns to the “MAINTENANCE MODE MENU” screen. 6-11-7 Device Check The NT631/NT631C provides checks on the functions of the following items. - Buzzer Page 222 - LED...
Page 231 Section 6-11 System Maintenance Select “Device Check”. Select “Buzzer Check”. S If the buzzer functions correctly, it will sound continuously. At this time, the “Buzzer Check” touch switch will be displayed in reverse video. S To stop the buzzer while it is sounding, press the “Buzzer Check” touch switch again.
Page 232 S To end the LED check, press the “LED Check” touch switch on the “DEVICE CHECK MENU” screen again. Checking the LCD (Screen Display) Check if the LCD display (or EL display for NT631) functions normally by following the menu operation from the System Menu shown below. Select “Maintenance Mode”.
Page 233 (red → green → blue → magenta → cyan → yellow → white → black). On completion of the display and clearance of all dots, the NT631/NT631C re- turns to the “DEVICE CHECK MENU” screen.
Page 234 - In the screen data memory check, a write test is performed on the screen data memory. Since all the screen data in the NT631/NT631C is lost in this check, confirm that this data is backed up at the Support Tool or memory unit before executing it.
Page 235 Section 6-11 System Maintenance Check the screen data memory by following the menu operation from the System Menu shown below. Select “Maintenance Mode”. Select “I/O Check”. Select “Device Check”. Select “Screen Memory”. Press “Execute”.
Page 236 S If an error is discovered in the check, the message “Memory Check NG” is dis- played. After confirming the result of the check, press “Quit”. The NT631/NT631C returns to the “DEVICE CHECK MENU” screen. Checking Touch Switches Check whether or not the touch switches function normally by following the menu operation from the System Menu shown below.
Page 237 A touch switch is normal if it is dis- played in reverse video while pressed. To end the check, press the touch switch at the top right corner (NT631: displayed in reverse video; NT631C: displayed in yellow). The NT631/NT631C will return to the “DEVICE CHECK MENU”.
Page 238 Select “Battery”. “The voltage is within the normal range.” or “The voltage is lowered.” is displayed. After confirming the result of the check, press “Quit”. The NT631/NT631C returns to the “DEVICE CHECK MENU” screen. Notice When “The voltage is lowered” is displayed, replace the built-in battery immedi- ately.
Page 239: Checking Interfaces
Section 6-11 System Maintenance 6-11-8 Checking Interfaces The NT631/NT631C allows the following communication functions to be checked. - Communication with the Support Tool Page 231 - Communication at serial ports Page 232 - Communication with printers Page 235 Checking Communication with the Support Tool Check communication with the Support Tool by following the menu operation from the System Menu shown below.
Page 240 S If communication with the Support Tool is normal, data transmitted from the Sup- port Tool is displayed as hexadecimal data when received by the NT631/NT631C. After confirming the result of the test, press “Quit”. The NT631/NT631C returns to the “I/F CHECK MENU” screen. Checking Communication at Serial Ports Check communication at the serial ports (A, B).
Page 241 Section 6-11 System Maintenance - For NT link (1:1 or 1:N) Example: Serial port B while using the NT link (1:N) Press “Execute” to start the check. The data for checking communication is sent to the host, and is displayed as “∗∗” symbols at “Sending Data”. - If communication with the host is normal, the reply from the host is displayed at “Received Data”...
Page 242 Section 6-11 System Maintenance - For a bar code reader The check starts when the check screen is displayed. Read data with the bar code reader in this status. - If communication with the bar code reader is normal, the read character strings are displayed in hexadecimal text code at “Received Data”.
Page 243 Select “Comm. Port A” or “Comm. Port B”. The check screen is displayed (“Check screen”, page 232). After confirming the result of the check, press “Quit”. The NT631/NT631C re- turns to the “I/F CHECK MENU” screen. Checking Communication with a Printer Check communication with a printer by following the menu operation from the Sys- tem Menu shown below.
Page 244 S If data does not reach the printer within 60 seconds after sending starts, the message ‘Finished Printer output failed’ is displayed. After confirming the result of the check, press “Quit”. The NT631/NT631C returns to the “I/F CHECK MENU” screen.
Page 245: 6-12 Programming Console Function
Section 6-12 Programming Console Function 6-12 Programming Console Function As an expansion function, the NT631/NT631C features the “programming console function”, which allows it to be used instead of a programming console (type C200H-PRO27-E) for a C-series CPM1, CQM1, C200HX/HG/HE (–ZE), or CS1-series CS1G/CS1H.
Page 246: Usable Systems
Programming Console Function Section 6-12 6-12-1 Usable Systems The programming console function can be used with an NT631/NT631C con- nected to a PC when using the communication method indicated below. Communication Communication Applicable PCs Connected Port Type Method (*1) C200HE-CPU42-(Z)E...
Page 247: Connection Method
CPU built-in RS-232C port and a peripheral port. Only the points of difference with an actual programming console are described here. For details on using the NT631/NT631C as a programming console, refer to the instruction manual for the programming console (C200H-PRO27-E).
Page 248 Section 6-12 Programming Console Function The “programming console” screen is displayed by operating the system menu as described below. Select “Expansion Mode”. Select “Programming Console”. The programming console screen is dis- played. Press the programming console sheet keys (touch switches) for the operation. Press the “Quit”...
Page 249 Section 6-12 Programming Console Function Key Operations S Mode selection keys, mode lock key The display element on the programming console screen shown below com- prises the mode selection keys, which change the operation mode of the PC, and the mode lock key, which prevents unintended mode changes. Mode selection keys Mode lock key The RUN, MONITOR, and PROGRAM mode selection key elements are touch...
Page 250 Section 6-12 Programming Console Function S Programming console keyboard The programming console keyboard used on the screen when the programming console function is used is comprised entirely of touch switches (shown by the dashed line frames in the figure below). On pressing a touch switch, a key op- eration is executed.
Page 251 S It is not possible to adjust the volume of the key press sound. Whether or not the key press sound sounds is determined by the setting for the “Key Press Sound” memory switch of the NT631/NT631C. It sounds when the setting is “ON” and does not when the setting is “OFF” (page 188).
Page 252: Nt631/Nt631C Functions
SECTION 7 NT631/NT631C Functions This section describes the functions of the NT631/NT631C. NT631/NT631C Screen ............
Page 253 7-14-8 Temporary Input Fields ..........7-14-9 Focus window .
Page 255: Nt631/Nt631C Screen
7-1-1 Screen Composition The NT631/NT631C screen is 640 dots wide by 480 dots high. Each dot is set by a combination of an X coordinate (horizontal direction) and a Y coordinate (vertical direction). The coordinate origin (0, 0) is at the top left of the screen.
Page 256 NT631/NT631C Screen Overlapping Screens The NT631/NT631C allows up to 8 screens to be displayed overlapped as one screen. A group of overlapped screens is called an “overlapping screen”. To allow distinction, the screen that results when the multiple component screens are overlapped is called the “parent screen”, and the individual component...
Page 257 Direct registration of elements on a parent screen is not possible. To display an overlapping screen on the NT631/NT631C, designate the screen number of the parent screen. The child screens will be displayed in the order they were registered (i.e., the first one registered will be the “bottom-most”...
Page 258 Apart from the normal (standard) screen display method, which a screen is dis- played over the entire panel area, the NT631/NT631C also allows screens to be displayed in one part of the screen area only. This partial screen is called a “win- dow”, and a screen on which a window is displayed is called a “window screen”.
Page 259 The types of system screens are indicated in the table below. Screen No. Name Function No-display screen If screen number “0” is designated as the display screen, the screen of the NT631/NT631C is made blank. 9000 “System initializing” This screen is displayed during the initial process- screen ing when the NT631/NT631C starts operation.
Page 260: Screen Attributes
7-1-4 Screen Attributes The NT631/NT631C allows attributes to be set for each screen, so that the func- tion specified by the attribute is executed when the screen is displayed. For exam- ple, when a screen for which the “buzzer attribute” has been set is displayed, the buzzer sounds.
Page 261 Section 7-1 NT631/NT631C Screen The setting for the “Buzzer Sound” memory switch at the NT631/NT631C takes priority in determining whether or not the buzzer actually sounds. When this memory switch is set to “ON”, the buzzer set with a screen attribute can sound.
Page 262 Section 7-1 NT631/NT631C Screen S Load Local1, Load Local2 Specify whether or not a window (Local1, Local2) pops up at the same time the screen is displayed by screen switching. Set the window screen number to be displayed when you check these attribute.
Page 263: Color Display
Black, blue, red, magenta, green, cyan, yellow, white The four color combinations below are in an XOR relationship. The NT631/NT631C has a function which prevents the display of an element on a background of the same color (making it invisible) by changing the color of the ele- ment to the color which is in XOR relationship with its present color.
Page 264 Black Reference When screen data is created for an NT631, black and white are displayed as white and black respectively at the Support Tool. On the display of a monochrome per- sonal computer, the display at the NT631 matches the colors displayed at the Sup- port Tool, but when a personal computer with a color display is used, the colors are reversed.
Page 265 Section 7-1 NT631/NT631C Screen S Impossible applications of the color designation “transparent” - Background of character strings displayed from character string memory tables - Background of numeric values displayed from numeral memory tables - Background of numeric values and character strings in numeral setting input...
Page 266: Lamps
Page 328 of various functions, such as notification to the host, to be executed by pressing the touch panel of the NT631/NT631C. They also have the same display functions as normal (standard) lamps. They can be displayed in any of the following forms: standard, shadow, 3-dimension, rectangle, circle,...
Page 267: Character String Display
The data contents of multiple numeral memory tables in the internal memory Page 374 of the NT631/NT631C are displayed in the form of a broken line graph. Trend graphs The data contents of multiple numeral memory tables in the internal memory Page 380 of the NT631/NT631C are displayed in the form of a trend graph.
Page 268: Areas For Control/Notification
PT Status Control Area (Host ↔ NT631/NT631C) 7-2-1 When data is written to this area from the host, the NT631/NT631C reads the data and operates accordingly. However, note that the number of the currently dis- played screen is written to the “screen switch setting” word from the NT631/NT631C too.
Page 269 Section 7-2 Areas for Control/Notification Allocated Words of the PT Status Control Area The PT status control area (host ↔ NT631/NT631C) can be allocated to the fol- lowing host (PC) areas. Symbol C Series PCs Allocation CVM1/CV Series PCs Allocation...
Page 270 “ON” status is also notified to the screen switch strobe flag of the “PT status” word of the PT status notify area by the NT631/NT631C (af- ter notification, the OFF status is re-established) (page 474). Whether the data is written in BCD or hexadecimal format is determined by the setting for “numeral storage type”...
Page 271 Designate the memory table numbers of the copy source and copy destination memory tables as 4-digit BCD or hexadecimal values, when copying data be- tween memory tables in the NT631/NT631C. Whether the values are BCD or hexadecimal is determined by the setting for numeral storage type in the PT con- figuration settings made with the Support Tool.
Page 272 PT status control bit operations to achieve agreement with the status of the NT631/NT631C. - The PT status control bits are checked in bit units by the NT631/NT631C. The only functions that are actually performed are those for which the corresponding...
Page 273 When bit 15 is turned OFF, the screen is cleared and the backlight also goes off. However, if the screen saver function is set with the memory switches of the NT631/NT631C, the screen saver is activated (the operation depends on the setting made for the screen saver function).
Page 274 Section 7-2 Areas for Control/Notification The contents of the words that reflect the status of an NT link (1:N) system are indicated below. Word Function 〈C200HX/HG/ “Communication in progress” flag of unit No. 0: HE (–Z)〉 ON when connected Word 265 “Communication in progress”...
Page 275 - The buzzer can also be controlled by using the “Buzzer” screen attributes (page 252). - Display history initialization (bit 11) This bit is used to initialize the display history recorded in the NT631/NT631C. When it is switched from 0 (OFF) to 1 (ON), the display history in the NT631/NT631C is initialized.
Page 276 - Memory table copy execute (bit 3), memory table copy type (bit 2) The “memory table copy execute” and “memory table copy type” bits are used to copy data between memory tables in the NT631/NT631C by PT status con- trol area operations.
Page 277: Pt Status Notify Area (Nt631/Nt631C To Host)
PT status notify area. - Alarm history initialization (bit 1) This bit is used to initialize the alarm history recorded in the NT631/NT631C. When it is switched from “0” (OFF) to “1” (ON), the alarm history in the NT631/NT631C is initialized.
Page 278 Section 7-2 Areas for Control/Notification Allocated Words of the PT Status Notify Area The PT status notify area (NT631/NT631C → host) can be allocated to the follow- ing host (PC) areas. Symbol C Series PCs Allocation CVM1/CV Series PCs Allocation...
Page 279 Close - PT operation status (bit 15) When the NT631/NT631C is in the RUN mode, this bit is set to “1”. In other modes, and when the System Menu screen is displayed, it is set to “0” (OFF). When this bit is set to “0” (OFF), the allocated bits and words are neither read or written.
Page 280 11-3-1 “Replacing the Battery” (page 623). - Screen switching strobe (bit 12) This bit is set to “1” (ON) when the NT631/NT631C screen is changed by an instruction from the host or by operation at the NT631/NT631C (ex. use of screen changeover function).
Page 281: Window Control Area (Host ↔ Nt631/Nt631C)
Data is written to the window control area from both the NT631/NT631C and the host. The status of the window is always written. When the data is written to this area from the host, the NT631/NT631C reads the data and display the window wit the specified number at the designated position.
Page 282 It is not necessary to allocate word to window control area when the window is not controlled from the host or when the window is not used. Allocated Words of the Window Control Area The window control area (NT631/NT631C(host) can be allocated to the following host (PLC) areas. Symbol...
Page 283 Tool. Functions of the Window Control Area If the NT631/NT631C is currently operating, the status of the window is always written to the window control area. The contents of the window control area de- pends on the window type (global window/local window) and the circumstances as follows.
Page 284 With Occurrence history screen (screen No.9001) and frequency history screen (screen No.9002) global window remains opened. Data is written to the window control area from both the NT631/NT631C and the host. The meaning of the data differs according to whether it is written from the...
Page 285 Areas for Control/Notification S When the data is written from the host: To switch, open, close or move a window on the NT631/NT631C by an instruc- tion from the host, write the window screen number or coordinates to the “win- dow No.”, “X coordinate”...
Page 286: Memory Tables
Section 7-3 Memory Tables Memory Tables The NT631/NT631C has the following three types of memory area that can be writ- ten to freely from the host. - “Numeral memory tables” for numeric value data Page 278 - “Character string memory tables” for text data Page 285 - “Bit memory tables”...
Page 287 Check mark (initialize)/No check mark (do not initialize) This setting determines whether or not the allocated words at the host are initialized when the power to the NT631/NT631C is turned ON, when the NT631/NT631C is reset, and on transition from the System Menu to the Initial RUN mode.
Page 288 The relationships among the allocated words, the number of allocated words, and the contents of numeral memory tables are indicated in the figure below. - When the number of allocated words is 1 word NT631/NT631C Numeral memory table Only four digits read ←...
Page 289 “Storage Type” and is stored after conversion to signed binary data. Accordingly, the same data will be interpreted in different ways by the NT631/NT631C depending on the setting made for “Storage Type”. Reference Signed binary data expresses negative values as the complement of two (the bits are inverted and 1 is added).
Page 290 Section 7-3 Memory Tables - Stored data The table below indicates how the set “Value” (initial value) and the contents of host words are stored in numeral memory tables. Storage of “Value” set at the Support Tool Number Display After Input Value Storage Type Stored Value...
Page 291 The “Initial” setting determines whether the contents of numeral memory tables are written to the allocated word(s) at the host when the power to the NT631/NT631C is turned ON, when the NT631/NT631C is reset, or on transition from the System Menu to the RUN mode.
Page 292 S By operation of the “PT status control area”, data can be copied between memory tables from the host (page 260). S If the contents of numeral memory tables are changed by operation at the NT631/NT631C, the change is notified to the “PT status notify area” (page 269).
Page 293: Character String Memory Tables
Since they can be allocated to words at the host, the contents of words at the host can be displayed as character strings at the NT631/NT631C via character string memory tables. Character string memory tables are assigned character string memory table num- bers so that they can be managed and designated individually.
Page 294 Check mark (initialize)/No check mark (do not initialize) This setting determines whether or not the allocated words at the host are initialized when the power to the NT631/NT631C is turned ON, when the NT631/NT631C is reset, and on transition from the System Menu to the RUN mode.
Page 295 The “Initial” setting determines whether the contents of character string memory tables are written to the allocated word(s) at the host when the power to the NT631/NT631C is turned ON, when the NT631/NT631C is reset, or on transition from the System Menu to the RUN mode.
Page 296 S By operation of the “PT status control area”, data can be copied between memory tables from the host (page 270). S If the contents of character string memory tables are changed by operation at the NT631/NT631C, the change is notified to the “PT status notify area” (page 269).
Page 297: Bit Memory Tables
Section 7-3 Memory Tables 7-3-3 Bit Memory Tables [Function Outline] Bit memory tables are internal memories for bit data. They are allocated to a bit at the host to monitors a bit, and can execute a specific function in accordance with the status of that bit. Bit memory tables are assigned bit memory table numbers so that they can be managed and designated individually.
Page 298 Section 7-3 Memory Tables S Operation when using the alarm list/history function The operation when using the alarm list/history function is as follows. Reference - For the alarm list function, display is in ascending order of bit memory table numbers. For the alarm history function display is in occurrence order (from newest record/from oldest record) or frequency order.
Page 299 Section 7-3 Memory Tables Reference - In the case described above, both “image/library display” and “screen change- over” functions are set. The operation when a touch switch is pressed is deter- mined as follows in accordance with these settings. Touch switch Image/library Image/library Screen...
Page 300 Section 7-3 Memory Tables S Allocated bit Bit memory tables can be allocated to the following host (PC) areas. Symbol C Series PCs Allocation CVM1/CV Series PCs Allocation CS1 Series PCs Allocation Data memory Data memory Data memory I/O relay I/O relay I/O relay Timer present value...
Page 301 Black/Blue/Red/Magenta/Green/Cyan/Yellow/White ground Color Color of message text (white and black for NT631) - If the “alarm list” and “alarm history” functions are registered for a screen, mes- sages and image/library data are displayed in accordance with the status of the bit memory table (refer to “Common Attributes”, page 291).
Page 302 Memory Tables Reference The alarm history can also be checked by pressing the “Alarm History” touch switch on the “MAINTENANCE MODE MENU” screen of the NT631/NT631C. For details, refer to 6-11-5 “Displaying and Printing the Alarm History Record” (page 217).
Page 303: Fixed Displays
...
Page 304 3 4 ) /" ( 1 ( 5 + ( ('( 5 /4 5 1 + + + + + + + + ( & '() ) ...
Page 305 * . )' ' % 8 , 0 - &' ...
Page 306 & ! "' + ' ) * . )' ' % ...
Page 307 ! "' + ' ) / ( )( 1 ; + < '( ...
Page 308 ! "' + ' ) + ) * '() )' '( / ) 1 !...
Page 309 ) ) * < < 4. 3= = % #&% '( 2;3$...
Page 310 " ) ) * ! "...
Page 311 * . )' ' % 8 , 0 - &' , -...
Page 312: Text (Fixed Display)
' " * + + ) / ) * ) ' ) & ' 1 " ( "' / ...
Page 313 ) ( * ) % % : ( 5. : - 0 - ...
Page 315: Tiling
, ) ( & ) ) () (' ( , )' ( ' * , + ( ( ( + + + + + / 1 ( &...
Page 316 ) ( ) 0 #& '( 2;9$ @ 4 % > ...
Page 317: Marks
' ) ' ) + + + + + / 1 ( & / 1 2 + ) "'* ...
Page 318 ! ( ('( ( & ) 6 ( & =' ) ( 2 + ( & 8 ' ) ( + ' ( ) + , ( & ...
Page 319 - # %2 $ %2 8 % & ) %% & '% ( %' ) 8 ( &+ ) ( ) ( ' * . )' ' ...
Page 320 , ) ( & ) ) () (' ( , )' ( ' , + ( ( ( % & ( 2 + )...
Page 321: Image And Library Data
# $% ,( ( ( ) < :6 5 + 5* ' 26 5 + 5* ' ,( ( "' + + ( =' ) ...
Page 322 ' ' ( ' ( ( * ) ( + 7 % ' "' - 1 - 1...
Page 323 ( ( ) " " ,+ ...
Page 324: Library Data Display
. ) ( ) ,( & ( ( + )' ) ) ) () " ( * ) + ) & ' (( ( + * =' ) ) ...
Page 325 ' ' ) ' ) ( * ) ) + 7 % ' "' 1 1...
Page 326 ) ( ) " " ,+ ...
Page 327 , ) ( @ ) ( ( @ ( ' / 41 -) ( ( 2 + ) "' ...
Page 328: Lamps
- ( ' ) - ( ( 9 ) > ( / 1 ( > ( / 1 ( ' /7@7>@ 1 ) 5## ...
Page 329 ! ( ('( 4 ( ) ( 5 + ( ('( 0 '() ( ) 6 '() ) 2 + '() ( + &...
Page 330 > ( / 1 - ( ) ( / 1 ( * ) * " 7 # $ <...
Page 331 * " ( # .6 / .6 / #- #- .5/3.5##/ .5/3.5##/ " .6 / .6 / #- ...
Page 333 8-- D( 6 + 8-- 7( > 7+ + 8-- ,+ 8-- # & '$ - - + 8--...
Page 334 < - 4 #& '( 21$ ,+8 @ 31 5## 5 * ! ) - ( ) ) /1 ...
Page 335 ' / 51 ( ' ( / * 1 ( - ( ( "' 2 + ) "' ...
Page 336: Touch Switches
>40@>40 ' ( ' ; /'1 ' + >40@>40 ) + ) ( ) *' 7 ! '+ ...
Page 337 * ' ' : (' ' ( ) ( (+ ( ' ' ' '* ' ( ( ; ' ' ' 8 ( 6 : ' ! ;...
Page 338 ,' & E ' : ' () '( @ '+ ' '( ' / ) 1 ) ' ' , ) ' ' ' & ' '* ( ' + ( ' ( ) ' & /0123+/0123...
Page 339 ' ( & ' : '() '( ' + ' ( & ) ( ' =' ' 9 ...
Page 340 (( ' ) . '+ ' ( ) " 7 # $...
Page 341 < - 4 #& '( 22$ ,+8 31 < 8 0 , ...
Page 342 G: * (H : * ( '+ ) * + ' /' 1 # .6 / .6 / #- #- ...
Page 343 " ' A%0@A ( '+ ) ' ' ( ' (( # !* 8>.,B - %( % + 4$ ' ' + ) *...
Page 344 , ' ' *' &) ' ' ) + & ' ) ' # & ' ( & '' '* (...
Page 345 4 31 0 / 5( ( ( ' ( ) * %(...
Page 346 0 7 . 7 /0 . 7 /0 . #%5 $ # %5 $ 5 #3$ / #2$ / # 8--$...
Page 347 A53+ A < 3 < < % % % > ,+8 ,+8 ,+8 0 0 0 ...
Page 348 * " > 0 /' 1 " '() 0 * " > / =' 1 " '() 0 * " > (( " '() * ...
Page 349 * ,' ' ) ' & ' / + ! 1+ ( ) >40@>40 * ! & ' /8> C D1 ( ' ' ' '...
Page 350 )' & / < 3 . 3 #C$ 3 2))) < ...
Page 351 & ' ' ' (( ) (( ) ' , '' '( @ + ' ( / * '1 (' '( @ ' ) ) () ...
Page 352 ' ( & ' ' ( ' * '( @ * ' ' , ) (' ' ' (+ '( ' * ' ( & ) '( '( @ * ' ...
Page 354 * : ( ) (('( ' < /1 * ; ' ( ( ( '+ ) ' ( ( ' * ' " & ' ' ...
Page 355 ; ' ' & E ' & E () >'* ( ,' / $1 " ,' / 1+ '( ' * ) ' # & ( & ) ( =' ' " ' ' /' & E 1 '( *...
Page 356: Numeral Display
...
Page 357 5 ...
Page 358 ! ; $ < %&; () ! *., 1 1 %< , 1 1 %< , " ! $ ! # % ! &...
Page 359 3# " ! 6 ! # 1! 6 & ( 4 6 2 ! ! # 1! ...
Page 360 -(0)$/ ! % - / < '= - / < * . * (0)$ ! % - / < )= - / < )* . * (0)$ ! % - / < - / < )* . * (0)$ ! % - / <...
Page 361 A5 B - / - %/ " ! # " 6 ! =! + ./>/0/0 " " ! ./>/0/0 ./>/0/> 2 + 7 ...
Page 362 A. B 7 - / - %/ ...
Page 363 3 3 7 -C / & -C / -2 # / 0)9 ...
Page 364: Character String Display
# , && &&&& ...
Page 365 # $ % & ' () ! * + , ...
Page 366 ! 5 ! ...
Page 367 6 2 %& ' ( ) 7 - %8 ''$9!!(/ 0 !! + , ! (( 0 ! ((...
Page 368 3# " ! 6 ! ! # 1! 6 & ( 4 ...
Page 369 2 2 2 )0 & "!0! -2 % 4 / '$...
Page 370: Graphs
30(@30(2 ! ! 1 5 0...
Page 371 5 # ! < $ ! # ! % , $: .
Page 372 ! % +E ! & # '( &D (, # ' # # 1 +E ! " ! # # +E 6 ! : + @@@ D 1 +E ! ...
Page 373 -/ , , - %/ &=(: &"(: # ! # ! ...
Page 374 ( 7 - %/ ! 3 , ,* F - F/ ...
Page 375: Analogue Meter
1 1 -%/ & -%/ -2 # / 00 ...
Page 376 ! 5 ! ! <...
Page 377 7 ! ! % , % # 1 , 5 15 6 7 ! 8 $ 5 1! 5 1! ! % # 1 , 5 15 6 7 ! 8 $ C6 !
Page 378 # ' # # 1 99++E ! " ! # # 99++E 6 ! : + @@@ D 1 99++E ! " ! 99++E % : 99++, 6 ! :...
Page 379 6 ! , ! , ! . ...
Page 380 +E +E # 9 4 # $ !: +E 9 " ! ,...
Page 381 ! 7 (F (F 8 %!!2 J 7 - %/ 83 F (F !!(F 7 - %/ 8&& F (F...
Page 382: Broken Line Graphs
% % E % F (F % ($F * % F ! (F 3 % % ...
Page 383 1, , ! , , ++E...
Page 384 , ! 5 % , ! <...
Page 385 ! % #1 , ++E % ++E ! & # '( &D (, # ' # # 1 ++E ! " ! # # ++E 6 ! : + @@@ D ...
Page 387 , , -! / -/ , ! ! (F -/ ...
Page 388: Trend Graphs
4 -F/ + , ! 7 -F/ , , - %/*...
Page 389 1, 1, 1, -%/ , & -%/ , -2 # / 0" ...
Page 390 , , ! , ...
Page 391 " % # 1 9 , 5 15 6 7 ! 8 $ C 6 ! " ! % # 1 , 5 15 6 7 ! 8 $ 6 ! " ! ! % # 1 ...
Page 392 ! % , % +E ! & # '( &D (, # ' # # 1 +E ! % 1 1 &" E(, " ! # # +E ...
Page 393 B!!! " # ! 1 1 % , 1 1 % , # ! " 1 1 % ,...
Page 394 # 6 )) ) ,) " ", ! 2 ) " 0 ) " )"...
Page 396 E -/ -/ (F -/ -/ A7 -% / -/B 7 !
Page 397 A7 -5 ./ -/B 7 # -/ ! 7 -/ 7 ...
Page 398 ( 7 - %/* ! 3 , ,* F - F/ ...
Page 399 , D 1 , ! , , ...
Page 400 A7 , B / ? " ) 0 ,) " B) " 0 ,) " , 2 ! ...
Page 401 - / 2 ! -E / 2 # ! ! ...
Page 402 @ @ -./ -/ G* % H , ", B" ! 2 " , 5 , D" ...
Page 403: Alarm List, Alarm History
& -C / ! , -%/ & -C / -%/ -2 # / 0' 7 , 7 , ...
Page 404 !"# ! # $ % $...
Page 405 / $ ...
Page 406 " $ & $ & $ & ...
Page 407 !# ) ' ' $ ' ' 2-344 45223"...
Page 408 $ * * "(( " $ 2 ' ...
Page 409 3 " , " * @ ! $&/0)" + 8@181#1131"1A 1 8@ '$ * @ $&/0)" + 8@181#1131"1A 1 ',, * @ $&/0)"...
Page 410 ' $ 9 8 & , 4 #( : )>>>...
Page 411 ' $ 9 .1 1 - * - -+...
Page 412 ( 1 $ ) !"# ...
Page 413 * !"# ! #$ * &...
Page 414: Inputting Numeric Values
9 ) ' $ & $ !:# ...
Page 415 & ' $ ' $ ' % $ " ...
Page 416 % -7 ! $ 5 & #$ 5' ' $...
Page 417 ' $ 9 3 . " , & , ...
Page 418 & 4 $ 5 #( : )>>> & 5 * 5 9))+ 1% , *$ 9))+ ...
Page 419 $ ' / $ $ ' ) / ...
Page 420 D9 E / / 4 % $ & . # 2 : <)9D9?0/9DE <)9D9?0/9? <)9D9?0/9D % ...
Page 421 D+ ' E * ' ' ' % / / 4 * 4 $ ...
Page 422: Thumbwheel Type ("Thumbwheel")
G !%$$# & & ' ' ' ' ' $ ( & &...
Page 423 ' $ ' ' & ' $ ' % $ " ...
Page 424 ) ! & # $ ) ' % $ ' 4 ...
Page 425 & 4 $ 5 #( : )>>> & 5 * 5 9)?+ 1% , *$ 9)?+ ...
Page 426 / # & @ , # 5 , # % @ ...
Page 427 D' / E ' / ! %# / 4 ! ' ' $#$ /A ' ' $...
Page 428 * 4 * ' $ $ ) ' & ' $...
Page 429 G !%$$# & & ' ' ' ' ' $ !%$$# &...
Page 430: Inputting Character Strings
! .6# ' $ ( ' ; 2 ! -;6#$ ' 4 $ 0'...
Page 431 $ $ , $ ...
Page 432 % -7 ! * $ 5 & * #$ 5' ' $...
Page 433 $ 9 3 . " , & , ...
Page 434 ) % $ ) $ ...
Page 435: Window Function
' $ ! 7 # $ ( ;- 4 2 ! -67#$ ) 1 ...
Page 436: Window Type
!" # ' ! #$ * ' $ 9 $ !
Page 437: Window Screens And Display Elements
, & ! # $ $3? $3? & 08'1 ' 2 & 0>1 ' $3? $3? 1$ ...
Page 438: Opening/Closing And Moving A Window
@ $ , $ G $ !@ @ -# " ' ...
Page 439: Size And Display Position Of A Window
& '() ' * ' * $ " * 4 $ , $ & $ ( ...
Page 440: Checking The Display Status Of A Window
# " $ " " * I J ! # ' $ * $ ( 6.
Page 441 * % $ . . % 5 . . ' > % * $ 0' ...
Page 442 0 1 $ !" $# ' $ ' ...
Page 443 5%A 5' '/ % '/ % 5' '/ % & . & . & . ) % ' - $ -$ ) & ) & ) & -...
Page 444 $ # % $ / 9 . 9 .< + 9 ..- 4 ' 9 .....
Page 445 !.# > & ? / & $ A 4 2 $ ) ! # 1 ! 1 #$...
Page 446 ( " & A & 2 $ / ) 1 -<$ ' ...
Page 447 4 <33 <33- ' $ $ + 5 3 4 1 ' !"#$ $ & ' ...
Page 448 " & " ( !"#$ 2 ! # ...
Page 449 & 2 4 2 4 2 $ ( 4 2 7 / 9 0 + ! -;#$ * & 2 & $...
Page 450 (1 7 3 % 33 K F F % 4) 4 5 3 #,22++)'0'' +"...
Page 451 + # #* 1 %: ' & ' & $ ) ! -.
Page 452 ++ 6,, 1 :: $ * :: $ :: $ "((A :: ' $...
Page 453 ) +,, * :: $ , 9 ! . 3#$ 0' :: :: M M 3 !"((#$ , :: ! . 3#$...
Page 454 +. )/ 1 & $ & & $ * ' 1 &...
Page 455 $ -.; -77 ' & $ ) ( & $ 4 4 2 / &...
Page 456 ) ' $ G * $ * $...
Page 457 & " & " 4 2$ $...
Page 458 " &5 7 !!,,## 11),, 6F=H F&I %G=H1=F&J @<9*** 08)9+ H%7= 8 %=# @<9*** 08)92 H%7= 8 %=# @<9*** 08)9< :! ,F=HF F @<9*** 08)9@ 6F=H F&I %G=H1=F&J @<9*** 08)09 6F=H F&I =,5 %% %6 @<9*** 08)0* 6F=H F&I %G=H1=F&J...
Page 459 9@ 9@$...
Page 460 % &' ( 9 4 $ 9 $ 0' 4 $ ( 4 Q$ $3 *<7 "...
Page 461 > 5? 4 $ ( ; 2 ! -;6#$ > 4 ? 4 ,/ $ 0' ' ...
Page 463: Screen Creation Procedure
Section 8-1 Screen Creation Procedure Screen Creation Procedure Follow the procedure shown below to create screens for the NT631/NT631C. The following gives the procedure assuming that the setting for the NT631/NT631C has been completed. The operating procedure for a Support Tool is not given here.
Page 464 Saving a File Save the created screen data to a file. Transmitting the Screen Data Transmit the created screen data to the NT631/NT631C. After setting the NT631/NT631C in the Transmit mode, execute the screen data transmission operation with the Support Tool. NT631/NT631...
Page 465: Buzzer, Backlight, And Display Control
The buzzer sounds intermittently at 0.5 second intervals. - Long intermittent sound The buzzer sounds intermittently at 1 second intervals. With the NT631/NT631C, the following two methods are used for sounding the buzzer. - Displaying a screen for which the buzzer attribute is set...
Page 466: Buzzer, Backlight, And Display Control
[Operation] When the screen where the buzzer attribute has been set is displayed during the operation of the NT631/NT631C, the buzzer sounds automatically according to the setting. For the procedure for changing the screen, refer to 8-3-1 “Switching the Screen” (page 469).
Page 467: Stopping The Buzzer Sound
Section 8-2 Buzzer, Backlight, and Display Control To sound the buzzer during the operation of the NT631/NT631C, operate the PT status control area as indicated below. (1) Set “1” (ON) for the following bit in the fourth word (n + 3 words) from the be- ginning of the PT status control area according to the required buzzer sound.
Page 468 Not used Always “0” To stop the buzzer during operation of the NT631/NT631C, operate the PT status control area as indicated below. (1) Set “0” (OFF) for all of the following bits in the fourth word (n + 3 words) from the beginning of the PT status control area.
Page 469: Controlling The Backlight (For Nt631C Only)
NT631/NT631C not operated for a while, or by operation at the PT status control area. Even when the backlight has gone off, it may light or flash according to the setting if the backlight mode is changed by operation at the PT status control area.
Page 470 Not used Always “0” To control the backlight status during the operation of the NT631/NT631C, operate the PT status control area as indicated below. (1) Set “0” (OFF) or “1” (ON) for bit 8 in the fourth word (n + 3 words) from the beginning of the PT status control area.
Page 471: Turning Off The Screen
[Setting] Using the system menu of the NT631/NT631C, set a value other than “000” for “Screen Saver Start up Time” (the length of time before the screen saver is acti- vated after the last NT631/NT631C operation) and “Display erased” for “Screen Saver Movement”.
Page 472 Not used Always “0” To turn off the screen during operation of the NT631/NT631C, operate the PT sta- tus control area as indicated below. (1) Set “0” (OFF) for bit 15 in the fourth word (n + 3 words) from the beginning of...
Page 473: Redisplaying The Turned-Off Screen
[Setting] No special setting is necessary. [Operation] Switching the screen during operation of the NT631/NT631C cancels the screen off status and displays the new screen. For the procedure for switching the screen, refer to 8-3-1 “Switching the Screen” (page 469).
Page 474 Not used Always “0” To redisplay the screen during the operation of the NT631/NT631C, operate the PT status control area as indicated below. (1) Set “1” (ON) for bit 15 in the fourth word (n + 3 words) from the beginning of the PT status control area.
Page 475 Section 8-2 Buzzer, Backlight, and Display Control [Setting] No special setting is necessary. [Operation] Pressing the touch panel cancels the screen off status to redisplay the screen which was displayed immediately before the screen was turned off.
Page 476: Screen Display And Notification
NT631/NT631C. 8-3-1 Switching the Screen The NT631/NT631C provides the following four methods for switching the screen. - Operation at the PT status control area - Pressing a touch switch that has the “Switch Screen” function - Using the screen switching function in the bit memory table...
Page 477 Reference - To display overlapping screens, specify the screen number of a parent screen. - When the NT631/NT631C is started up, the screen of which screen number is stored for “Screen Switch Setting” in PT status control area is displayed.
Page 478 Section 8-3 Screen Display and Notification Reference - To display overlapping screens, specify the screen number of a parent screen. - The screen is not switched if elements have not been registered to the specified screen number. [Operation] (1) Press the touch switch with the screen switching function when the screen is to be switched.
Page 479 “0” (OFF). Reference The screen of the NT631/NT631C is switched at the timing the status of the bit to which the bit memory table is allocated is changed from “0” (OFF) to “1” (ON).
Page 480 (character string memory table) or image data/library data. The function can also switch over the screen to a specified one. Message and image/library data which correspond to bit memory table No. 10 NT631/NT631C Character string table 50 Character string No. 9 Image library 124A memory table No.
Page 481 Section 8-3 Screen Display and Notification - Screen number: Screen number of the screen which corresponds to the “1” (ON) bit in the bit memory table (in the host). @ 0001 to 3999: Screen No. 1 to No. 3999 @ 9001: Occurrence history screen @ 9002: Frequency history screen...
Page 482: Finding The Screen Number Of The Presently Displayed Screen
8-3-2 Finding the Screen Number of the Presently Displayed Screen The NT631/NT631C has a function to notify the host of the occurrence of a screen switching event, and the screen number of the new screen when the display screen is switched by operation at the NT631/NT631C.
Page 483 (1) Read out the beginning (word n) of the PT status control area with the pro- gram in the host. The screen number of the screen displayed at the NT631/NT631C is stored in a 4-digit BCD or a 4-digit hexadecimal. Whether BCD or hexadecimal notation is to be used is set for “Numeral Storage Type”...
Page 484 Screen Display and Notification Reference While the NT631/NT631C is running, the screen number of the currently displayed screen is always recorded in the “screen switch setting” word in the PT status con- trol area (except when the screen displayed is an error screen or the System Menu screen, in which case the screen number of the screen displayed immediately be- fore remains recorded).
Page 485: Display And Control Of Windows
Reference - If “1” (disable) is set for the “window opening” PT status control bit, it is not pos- sible to open a window by operation at the NT631/NT631C. (Closing of a win- dow is allowed.) - If the window for which “open” is specified is not a window screen, the window open command is disregarded.
Page 486 Opening/Closing a Window by Pressing a Touch Switch That Has the “Input Key – Keyboard” Function If this method is used, the specified window can be opened and closed by opera- tion at the NT631/NT631C. By this method, only the local window can be controlled.
Page 487 In this method, a specific window (keyboard screen) can be opened at the same time as a numeral or character string input field is specified by operation at the NT631/NT631C. When a cursor moving key is used, the window opens in the same manner as an input key-window/keyboard function which has “open”...
Page 488 The window is changed to a frame display only with a “+” mark at the center of (2) Press the touch panel of NT631/NT631C at a destination position of the win- dow. Window is moved to that position. (The center position of the window comes to the pressed position.
Page 489 Section 8-4 Display and Control of Windows [Operation] In the window control area, the following three words are provided for each global window, local window 1 and local window 2. Word Screen No. (4-digit BCD or hexadecimal) X coordinate (4-digit BCD or hexadecimal) Global window Y coordinate (4-digit BCD or hexadecimal) Screen No.
Page 490 Section 8-4 Display and Control of Windows (2) To move the position of a presently displayed window, write the new coordi- nate to “X coordinate” and “Y coordinate” in the window control area which corresponds to the window. The values which can be specified is same as for (1) (open). (3) To close a presently displayed window, write 0000 to “window screen number”...
Page 491: Checking The Display Status Of A Window
8-4-2 Checking the display status of a window NT631/NT631C has a function to notify the open/close status of a window, the screen number and the position of presently displayed window to a host when the display status of a window is switched.
Page 492 Section 8-4 Display and Control of Windows [Operation] To check the display status of a window, operate as follows. S Reading out the opening/closing status of a window The bit for notifying the PT status (PT status notify bit) is provided at the second word (word m + 1) from the beginning of the PT status notify area.
Page 493 The window screen number and bottom left X, Y coordinates of the window which is presently displayed on the NT631/NT631C are stored in 4-digit BCD or hexadecimal. Which of BCD or hexadecimal is used is determined by the setting of “Numeral Storage Type”...
Page 494: Disabling/Enabling The Opening Of A Window
Controlling the Window by Operation at the PT Status Control Area This method allows the opening of a window by operation at the NT631/NT631C to be disabled. (Even if the opening of a window is disabled, it is possible to close the window by operation at the NT631/NT631C, or to move a window by a touch switch operation which has “window move”...
Page 495: Changing Numeral And Character String Display
With this method, however, only the contents of the allocated words of memory tables being used for display on the current screen of the NT631/NT631C can be read out. Contents of an allocated word which is not related to the display are not read out.
Page 496 Section 8-5 Changing Numeral and Character String Display When allocating a numeral memory table to the host, the following properties can be specified. Even with the same data, the method of storage in a numeral memory table differs depending on these specifications. S Storage type - BCD: The contents in the allocated word are regarded as BCD (binary coded deci-...
Page 497 Section 8-5 Changing Numeral and Character String Display S Examples of allocated word data stored in a numeral memory table How the contents at a word in the host are stored to a numeral memory table is shown below. Contents of Contents of Words Storage Type...
Page 498 NT631/NT631C (if the background function is set for a trend graph, the contents of the corresponding word are always read out). The con-...
Page 499 [Direct specification] An example of displaying the contents of a PC word allocated to a numeral memory table as they are is shown below. The display on the NT631/NT631C screen changes as the contents of the PC word change. S Setting at the Support Tool Set as indicated below using the Support Tool.
Page 500 “1” every second. (2) Each time carry over occurs during processing at (1) above, the contents of D0001 are incremented by 1. At the NT631/NT631C, the value of the higher 4 digits in numeral memory table No.1 increases by 1.
Page 501 Section 8-5 Changing Numeral and Character String Display Touch switch No. 10 LINE TARGET units ACHIEVED Numeral display (numeral memory table No. 51 is designated in indirect specification) Touch switch No. 11 S PC program Make a PC ladder program as shown below. The program must also be made so that the value of “ACHIEVED”...
Page 502 NT631/NT631C. The character string is displayed only up to this code since it is regarded as the end of the characters. When writing character codes to a word, do not write 00 in a character string.
Page 503 An example of displaying the contents of a PC word allocated to a character string memory table as they are is shown below. The display on the NT631/NT631C screen changes as the contents of the PC word change. If the system is so config-...
Page 504 DM0000 in indirect specification S Program operation (1) The display on the NT631/NT631C changes to the next item in the se- quence “NT631C” → “NT631 ” → “NT31C ” → “NT31 ” each time bit 00100 comes ON. (2) The display on the NT631/NT631C changes to the next item in the se- quence “NT31 ”...
Page 505 20 words for a character string memory table in the NT631/NT631C. If the memory table is allocated to a word in the host, however, copying may not be executed correctly if the “Words” settings differ between the memory tables (copy source and copy destination tables).
Page 506 Section 8-5 Changing Numeral and Character String Display [Operation] The following areas are provided in the PT status control area to be used for copy- ing the data between memory tables. - 2nd word from the beginning of the area (word n + 1) Copy source memory table No.
Page 507 Section 8-5 Changing Numeral and Character String Display (1) Write the memory table numbers in the PT status control area as indicated below in either 4-digit BCD or 4-digit hexadecimal. Which of the BCD and hex- adecimal notations is used is determined by the setting for “PT Configuration” –...
Page 508 Section 8-5 Changing Numeral and Character String Display [Example of Use] S Setting at the Support Tool Set the word and the contents with the Support Tool as indicated below. - Allocated word in the PT status control area: 00100 (word 100 in the CIO area) - Contents to be registered for the screen: Character string memory table No.
Page 509 Memory table copy execution bit set from 1 to 0 #FFF7 S Program operation (1) If an error occurs (bit 09000 goes ON), the display on the NT631/NT631C changes to “FAULT”. (2) When the error is eliminated (bit 09000 goes OFF), the display on the...
Page 510 This method allows an operator to change the contents of a memory table simply by operation at the NT631/NT631C. It is also possible to copy data to a numeral setting/character string input field by using this method. With the “Copy Setting”...
Page 511: Display Of Graphs
Section 8-6 Display of Graphs Display of Graphs This section describes the method for changing the graph display which shows the contents of numeral memory table, taking the trend graph as an example. For details of changing the contents of numeral memory table, refer to 8–5 “Changing Numeral and Character String Display”...
Page 512: Input Of Numeric Values And Character Strings
Input of Numeric Values and Character Strings Input of Numeric Values and Character Strings The procedure for inputting numeric values and character strings by operation at the NT631/NT631C is described below. 8-7-1 Inputting a Numeric Value The touch switch “control code input function” is used to input numeric values.
Page 513 Section 8-7 Input of Numeric Values and Character Strings [Setting] When creating a screen using the Support Tool, set the elements indicated below on the screen. - Numeral setting input field (numeric key type) - Touch switch “input key – control” @ 0 to 9 @ A to F (only for the numeral setting input field of the hexadecimal...
Page 514 Section 8-7 Input of Numeric Values and Character Strings S Inputting operation using touch switches A numeric value can be input in the same manner as when using an electronic calculator by using the touch switch “input key – control”. <Initial display>...
Page 515 Section 8-7 Input of Numeric Values and Character Strings Even when more than one numeric key type numeral setting input field exits on the screen, the input objective does not shift after the confirmation of the input. <Initial operation of input keys> How the sign (") key, the decimal point (.) key, and alphabetic letter (A to F) keys operate in the initial input (the first input after the screen is displayed or after the confirmation of the previous input) is described below.
Page 516 Section 8-7 Input of Numeric Values and Character Strings Cases Where Multiple Numeral Setting Input Fields Exist on a Screen (Without Cursor Moving Keys) The following describes the procedure for inputting a numeric value at a screen which has multiple numeric key type numeral setting fields. The explanation is giv- en for the operation which uses the “input key –...
Page 517 Section 8-7 Input of Numeric Values and Character Strings [Operation] (1) Display the screen where a numeral setting input field is registered. (2) Specify the objective numeral setting input field using the “input key – control” (HOME, ↑, ↓, ←, →, For the procedure for specifying the objective input field, refer to “Specifying the objective numeral setting input field using input key –...
Page 518 Section 8-7 Input of Numeric Values and Character Strings <Specifying the objective input field using the keys> Pressing the keys shift the objective input field in the order the input fields were created using the Support Tool. When three numeral setting input fields have been created, for example, the ob- jective input field shifts in the order they were created as shown below.
Page 519 Section 8-7 Input of Numeric Values and Character Strings [Setting] When creating a screen using the Support Tool, set the elements indicated below for the screen. - Numeral setting input fields (numeric key type, with cursor moving keys) (2 or more fields) - Touch switch “input key –...
Page 520 Section 8-7 Input of Numeric Values and Character Strings Inputting Numeric Values Using the “Input Key – Control” in a Window The following describes the procedure for inputting a numeric value into a numeral setting input field in the base screen using the “input key – control” registered for the window.
Page 521 Section 8-7 Input of Numeric Values and Character Strings Reference For the registration of touch switch “input key – control”, it is useful to register the keys which will be required for inputting the data on the base screen, and those which will be switched according to need during input —...
Page 522 Section 8-7 Input of Numeric Values and Character Strings Inputting Numeric Values Using the Temporary Input Field The following describes the procedure for inputting a numeric using a “temporary input field” which is registered for a window. The term “temporary input field” means a numeric key type numeral setting input field registered for a window.
Page 523 Section 8-7 Input of Numeric Values and Character Strings - “Window open key” touch switch Specify the window screen number of the window used for inputting a numeric value. (Used when opening the window for inputting a numeric value. This operation is not necessary if the “window open”...
Page 524 Section 8-7 Input of Numeric Values and Character Strings Reference - If a temporary input field is set in a window, the input is automatically set in the temporary input field. When multiple windows are opened and the each window has an input field (temporary input field), the data is set in the input field in a focus window.
Page 525 Section 8-7 Input of Numeric Values and Character Strings [Example of Use] <Base screen> <Window> 5 input settings Temporary input field 8 integer digits, no sign display (8 digits can be displayed) 00000001 Integer digits: 8; Decimal fraction digits: 0; Sign display: No;...
Page 526 Section 8-7 Input of Numeric Values and Character Strings Inputting Numeric Values Using a Thumbwheel Type Input Field The following describes the procedure for inputting a numeric value into a thumb- wheel type input field. – – – – Decrease by “1” when key is touched –...
Page 527 [−] key changes the sign to “−”. <Checking the upper/lower limit> The NT631/NT631C has a function to check the correctness of an input numeric value to prevent a numeric value outside the allowable range from being input so that the input of an illegal value will not adversely affect the system.
Page 528: Inputting Character Strings
“numeric value input”. In character string input operation, bar code data can be input as a character string using a bar code reader which is connected to the NT631/NT631C. Only the following topics are described here. - Using the “input key – string” on the same screen...
Page 529 Character string input field Display NT631C Input NT631C NT631 NT31C Reference It is possible to copy the contents in the character string memory table to the char- acter string input field using the touch switch “Copy Setting” function (page 503).
Page 530 - Selection of “Auto/Manual” is made in the settings for the communication condi- tions of a bar code reader at the System Menu of the NT631/NT631C. - It is possible to copy the contents in a character string memory table to a charac-...
Page 531 Section 8-7 Input of Numeric Values and Character Strings [Setting] When creating a screen using the Support Tool, register the following elements for the screen. - Character string input field If a bar code reader is used in “Manual”, the following touch switch “input key – string”...
Page 532: Using The Alarm List/History Function
The Support Tool can read out the alarm history record data stored to the NT631/NT631C to the host as a text file. For the procedure for reading the alarm history record data, refer to the NT-series Support Tool Ver. 3.0 for Windows95/98 Operation Manual (V053-E1-j).
Page 533 @ Type: Order of frequency or order of occurrence To display the alarm history in the order of occurrence, set the display order (From Old Data/From New Data) of the record data using the Hist. Disp. Meth- od memory switch of the NT631/NT631C.
Page 534 Section 8-8 Using the Alarm List/History Function [Operation] (1) Initialize the recorded alarm history record data as needed. To initialize the alarm history record data using System Menu operation, se- lect “Alarm History” on the “MEMORY INIT. MENU” screen. To initialize the alarm history record data by operation at the PT status control area, change the status of bit 1 in the 4th word (word n + 3) from the beginning of the PT status control area to “1”...
Page 535 The recorded alarm history record data can be confirmed from the System Menu. It is possible to print the alarm history record data using a printer connected to the NT631/NT631C. S Display in the order of occurrence S Display in the order of frequency...
Page 536 To display the alarm history in the order of occurrence, set the display order (From Old Data/From New Data) of the record data using the “Hist. Disp. Meth- od” memory switch of the NT631/NT631C. [Operation] (1) Initialize the recorded alarm history record data as needed.
Page 537: Using The Display History Function
The display history can be checked using the System Menu of the NT631/NT631C. It is also possible to check it during operation by displaying the display history screen. Concerning the display history record data stored to the NT631/NT631C, the Sup- port Tool can read it out to the host as a text file.
Page 538 To display the alarm history in the order of occurrence, set the display order (From Old Data/From New Data) of the record data using the “Hist. Disp. Method” memory switch of the NT631/NT631C. [Operation] (1) Initialize the recorded display history record data as needed.
Page 539 Section 8-9 Using the Display History Function - Display in the order of occurrence (screen No. 9001) - Display in the order of frequency (screen No. 9002) (3) It is possible to display the previous and the next page by pressing the ↑ and ↓ keys.
Page 540: 8-10 Display And Setting Of Calendar Clock
No. 255 are for setting. Memory tables No. 247 to No. 253 store the clock data which is updated accord- ing to the operation of the clock built into the NT631/NT631C. The data in these memory tables cannot be changed from the host.
Page 541: Setting The Date And Time
Pressing a Touch Switch Which Has the “Copy Setting” Function” (page 503). Reference The NT631/NT631C does not check the set date and time data strictly. Therefore the data must be set correctly so that there is no discrepancy between the date and...
Page 542 Section 8-10 Display and Setting of Calendar Clock [Setting] Prepare two numeral memory tables to write the required values for copying it to numeral memory table No. 254 and No. 255. - PC Address: Any word in the host - Words: 2 words - Storage Type: Binary Use the PT status control area to copy memory tables.
Page 543 Section 8-10 Display and Setting of Calendar Clock PT Status Control (word n + 3) Controlled Item 1 (ON) 0 (OFF) Screen display Performed Not performed Processing priority registration (for NT link (1:N)) Registered Canceled Continuous buzzer Sounded Stopped Intermittent buzzer (short) Sounded Stopped Display history initialization...
Page 544 PT status control area (designation of memory table copy execution). Contents of numeral memory table B are copied to numeral memory table No. 255 and the day of week, year, and month are set for the NT631/NT631C. [Example of Use] Refer to the “Example of Use”...
Page 545: Displaying The Date And Time
Displaying the Date and Time The procedure for displaying the date and time data set using the clock function of the NT631/NT631C by the numeric value display of numeral memory tables No. 247 to No. 253 is described below. Numeral memory tables No. 247 to No. 253 store the date and time data as shown below and the stored data is constantly updated.
Page 546 Section 8-10 Display and Setting of Calendar Clock Numeral memory table No. 251 (2-digit display) Numeral memory table Numeral memory table No. 252 (2-digit display) No. 250 (2-digit display) 19 98 Numeral memory table Numeral memory table No. 249 (2-digit display) No.
Page 547 (2), the memory table copy execution bit (10303) is re- turned to the OFF status. (4) After a wait of about one second for the NT631/NT631C to confirm that the memory table copy execution bit has gone OFF, the program copies the contents of numeral memory table No.
Page 548: Printing Data And Checking The Printer Status
The following data below can be output to a printer connected to the NT631/NT631C while the NT631/NT631C is operating. - Hard copy of the screen The status of the printer connected the NT631/NT631C can be checked from the host. This section describes the procedure for printing data during operation and also the procedure for checking the printer operating status.
Page 549: Printing The Screen
Bit 7 ON Printing Reference - The NT631/NT631C continues operation even while the screen hard copy is be- ing printed. - It is necessary to ensure that the “printer operation status” (bit 7) among the PT status notify bits is “0” (OFF) before starting printing.
Page 550 If this method is used, the screen can be printed out by operation at the NT631/NT631C. To use this method for printing the screen, however, a touch switch which has the “print screen” function must be registered for the screen.
Page 551 Section 8-11 Printing Data and Checking the Printer Status Reference - The NT631/NT631C continues operation even while the screen hard copy is be- ing printed. - By registering a touch switch with the print stop function, it is possible to stop printing by using this touch switch.
Page 552: 8-12 Enabling/Disabling Pt Operations
- When screen switching is disabled, all kinds of screen switching operations at the NT631/NT631C, such as screen switching using a touch switch and by the alarm list/history function, are not possible. Note that the display of the System Menu using the touch panel and screen switching by an instruction from the host using the PT status control area are still possible.
Page 553 Not used Always “0” To control the operation by the NT631/NT631C while it is running, operate the PT status control area in the manner shown below. (1) Change the setting of the bits in the fourth word (word n + 3) from the begin- ning in the PT status control area as indicated below according to the required control.
Page 554 " # $ %& !! ' # ...
Page 555 ! " # # $ # ! %&'(%&' %&'(%&' (! # ( ...
Page 556 $ ! %&'(%&' ! 5 6 (6" # %&'(%&' " %&'(%&' " ! - ...
Page 557 % $ " %&'(%&' / %&'(%&' " ! $ ! " # 717...
Page 558 " ! " ! 609'9 8.0: -" ! %&'(%&' " ! ! " ;<...
Page 559 /" : ! ! %&'(%&' ! " ! " " 2" ! ! ; " 1,< # ! ! ! 2% " ...
Page 560 " $ ! $ ! 0" " " $ $ 8.0: " ! " .0:: % -" " !...
Page 561 # : " " : " ; <...
Page 562 ! " ! (' .* / .*/ . / ./ '! " ( ; 85 < + ) . ) # 3 ) . ; ! <...
Page 563 ! ; - < + 0 D : $ ! ;9 - <...
Page 564 " ! (' .* / .*/ . / ./ '! " ( ; 85 < + ) . ) # 3 ) . ; < , ) # ; <...
Page 565 ;9 - < ! 6 " " . - ++ : " - 9+ : 9+ " " " " 9+ % ! ...
Page 566 (' '! ; 85 < ++++ ,,, ;9 ;- < " + < ++ ;#'1 :0/ 337,<...
Page 567 # $ " ! (' .* / .*/ . / ./ '! " ( ; 85 < + ) . ) # 3 ) . ; < , ) # ; <...
Page 568 ; - F < ++++ " ;/E+ /%E< & - $ ; ! <...
Page 569 % ! (' . / ./ '! " ( ; 85 < + ) . ) # ;9 - < (' '! ...
Page 570 & ! (' . / ./ '! " ( ; 85 < + ) . ) # ;9 - < (' '! ;9 - <...
Page 571 ' ( ! (' .* / .*/ , 1 2 , 1 2 . / ./ '! " ( ! ; 85 < + ) . 0> ) # 0> 9 ) . .%5 ' ) # .%5 ...
Page 572 / 2@ 26" ! " ! " (' '! ;9 - < ! ; - 24< " ! " ! # - " " ;! <...
Page 573 ) " ( ! (' .* / .*/ , 1 2 , 1 2 . / ./ '! " ( ; 85 < + ) . ) # 3 ) . ; ! <...
Page 574 / @ 6" ! " ! " ;9 - < ! ; - 29+4< " " .
Page 575 " ( ! (' . / ./ '! " ( ; 85 < + ) . )# ! ; 85 < ++++ +,, ...
Page 576 * $ " ( ! (' .* / .*/ , 1 4*) , 1 4*) . / ./ '! " ( ; 85 < + ) . ) # 3 ) . ; $ ! ! <...
Page 577 / 2@ 26" ! " ! " (' '! ;9 - < ! ; - 24< " " .
Page 578 " ( +, ! ! (' . / ./ '! " ( ; 85 < + ) . ) # ! ! ; 85 < ++++ ,,,, ! ! ; 85 <...
Page 579 " ! (' .4 / .4/ .4/ .4/ .) / .)/ .)/ .)/ . / ./ '! " ( ; 85 < + ) . ) # ; 85 <...
Page 580 " ! (' .4 / .4/ .4/ .4/ .)/ .)/ .)/ .) / . / ./ '! " ( ; 85 < + ) . ) # ; 85 <...
Page 581 # $ " ! .4 / .4/ .4/ .4/ (' .) / .)/ .)/ .)/ . / '! " ( ; 85 < + ) . ) # ; 85 <...
Page 582 % ( - ! (' '! ! ; 85 < ++++ ,,,, ! ! ! ! ; - <...
Page 583 (' '! ! ) ++94 ! ;- <) '+'4 ; ) ++ ++++ +++ ++< ;- <) +++4; ) ++++ ++++ ++++ +++< ;- < ) +54 2 ! 2 ! ++ ! ++94 ...
Page 584 % : ! " # " $ " 0 " ! %91 %97' ; "( < - ...
Page 585 ' - ! (' '! : " ; 85 < ++++ +,, ! " ...
Page 586 ) . ! A>0B '! ; 85 < ++++ ,,,, 5) 6) 1 7) 7) ) ) 4) # * ) 3 ** ) 2...
Page 587 % % # ;# # ! ! <...
Page 588 ! # ) +4 % ! # ) 4 # ;- < ) 3+3+4 ;# " " ) /%< ) .4 &$ # % ! ! ! ! ! " # : " ! ...
Page 589 ! (' '! ! # ; 85 < ++++ ,,,, % ! ;9 85 < + 7+ ...
Page 590 * - ( ! (' . / ./ '! " ( ; 85 < + ) . ) # /" # ! ;9 85 < - ++ ; <...
Page 591 " # 6% # 6% $ 25" 0 ! 25 . ! ! " $ 20 # ! ...
Page 592 1 - ! '! (' > ;9 85 < + ) : $ . - +9 ) " +' ) 6 ! ( + ) " ( " ...
Page 593: Function Applications
This section presents a collection of simple practical examples that will give you hints on how to make best use of the func- tions of the NT631/NT631C. Please use these examples for reference when using the NT631/NT631C. 10-1 Examples of Actual Applications of Direct Access .
Page 594: 10-1 Examples Of Actual Applications Of Direct Access
Some examples that will give you an idea of how to actually apply the functions of the NT631/NT631C such as those indicated below are presented here. S Continually monitoring a specific PC bit and displaying an alarm when it comes ON ..
Page 595 Example: Displaying a screen with “TEMPERATURE ABNORMAL” in black on a red back- ground when the monitored PC bit comes ON. NT631/NT631C Screen switched TEMPERATURE ABNORMAL (1) Set the properties of the screen displayed when the bit comes ON as follows.
Page 596 (page 328), writing a screen number to the control area (page 260), or switching the screen by using a bit memory table (page 289). Example: Displaying a screen that shows details of the error when the “TEMPERATURE AB- NORMAL” alarm message is pressed. NT631/NT631C 192_C 165_C 183_C TEMPERATURE ABNORMAL 250_C 180_C 175_C...
Page 597 ON, the bit that indicates the error location for the relevant temperature also comes ON. Example: Displaying a screen with details of the times at which alarms occurred in the past when the “TEMPERATURE ABNORMAL” alarm message is pressed. NT631/NT631C TEMPERATURE ABNORMAL13:12 CONVEYOR STOPPED 11:47 TEMPERATURE...
Page 598 - No. 9002: Frequency History Screen (page 436) In this case, there is no need to register an alarm list. Example: Displaying the corrective action (help information) when the alarm message “TEMPERATURE ABNORMAL” is pressed. NT631/NT631C Library data Inspect ... TEMPERATURE ABNORMAL...
Page 599 (3) above. Changing Display Contents in Accordance with PC Bit Status Example: Changing the status of a graphic depicting the opening and closing of a valve in accordance with the status of one PC bit. NT631/NT631C OFF state ON/OFF ON state...
Page 600 Check mark set, code of the figure depicting the open valve created in (1) - PC Address: Number of the bit used to change between the figures Example: When the displayed character string is changed in accordance with the status of one PC bit NT631/NT631C TRANSPORTING OFF state ON/OFF TRANSPORT ON state OVER (1) Create library data with fixed display text reading “TRANSPORTING”, and...
Page 601 (3) Register image/library lamps set for bits 1 to 15 in the same way as in (2). Reference With NT631/NT631C, once an element has been drawn, it is not redrawn unless the display contents change (this applies even with overlapping screens). Conse-...
Page 602 Section 10-1 Examples of Actual Applications of Direct Access Displaying Online Help with a Touch Switch Example: Displaying help information in a window when a touch switch is pressed. NT631/NT631C How to use ... Window opens Close HELP HELP Window closes (1) Create a new screen as a keyboard screen.
Page 603 Continually Monitoring a Specific PC Bit and Displaying a Message on a Window When It Comes ON Example: Opening a window and displaying an error message on it when the monitored bit at the PC comes ON. NT631/NT631C TEMPERATURE ABNORMAL MOVE...
Page 604 Section 10-1 Examples of Actual Applications of Direct Access (5) Create the following ladder program so that the window is opened from the host when the bit comes ON. (Word numbers are not shown in the ladder pro- gram below, set the value when programming.) error bit @MOV(21) Window screen No.
Page 605 Section 10-1 Examples of Actual Applications of Direct Access Continuously Reading Out the Contents of a PC Word and Displaying a Trend Graph by Backtracking Example: Utilizing the trend graph logging function and background function (1) Register a trend graph set as indicated below for the screen. - Line Properties: Word No.
Page 606 Section 10-1 Examples of Actual Applications of Direct Access If required, past status changes can be displayed as a trend graph. Part being displayed “Previous Page” “Next Page” (Rewind) (Forward) touch switch touch switch Hints S Apart from the “Previous Page” (Rewind) and “Next Page” (Forward) touch switches indicated above, the following touch switches can be created without restriction to control the display and data recording (7-10-4 “Trend Graphs”, page 381).
Page 607 Section 10-1 Examples of Actual Applications of Direct Access (1) Set the initial values indicated below for character string memory tables No. 0 to No. 6. Do not allocate these character string memory tables to words at the host. Character string memory table Initial value (2) Register the part that displays the month and day for the screen, following the example given above.
Page 608: 10-2 Examples Of Actual Applications Of Memory Link
Example: Switching screen by the operation at PT control area: Allocated word in PT control area: 0100CH Host NT631/NT631C Command Screen No. 10 Screen No. 15 Use “PT memory write command” (sent from host to PT) for this case since it is necessary to write new screen number to the first word in PT control area.
Page 609 S Use “bit memory table write command” to switch screens by the operation of bit memory table. see page ?? To know the event that a numeral/character string is input to PT Example: Host NT631/NT631C Production Numeral data volume 0001 No.
Page 610 Section 10-2 Examples of Actual Applications of Memory Link (1) When numeral data is input on PT (“numeral input notify command” sent from PT to host): S Command [ESC] [CR] S Explanation - Numeral memory table number : 142 - Input numeral : 00000000F0 (240 in decimal) - Check sum...
Page 611 Section 10-2 Examples of Actual Applications of Memory Link S Explanation - Check sum present/absent : None (writing 1 word) - First numeral memory table No. written : 142 - Data of written numeral memory table : 000004B0 (1200 in decimal) In this way, numeral data which is input from the PT is processed at the host and the result is notified to the PT.
Page 612: Troubleshooting And Maintenance
SECTION 11 Troubleshooting and Maintenance This section describes the action to take when NT631/NT631C errors occur, and how to carry out maintenance and inspection to prevent the occurrence of errors. 11-1 Troubleshooting ............. .
Page 613: Troubleshooting
Section 11-1 Troubleshooting 11-1 Troubleshooting When a fault relating to the operation of the NT631/NT631C occurs, find the symp- toms in the table below and respond by following the corresponding “Remedy” in- dicated in the table. Notice - Confirm system safety before turning the power ON/OFF or resetting.
Page 614 Cause Remedy Symptoms The PC mode has The NT631/NT631C changes the This is an NT631/NT631C specification. When using changed to the monitor mode when host link communication a PC that can also be connected using the NT link mode. is used.
Page 615: Troubleshooting
Section 11-1 Troubleshooting NT631/NT631C Cause Remedy Symptoms The System Menu cannot “Display System Menu” under In the System Installer mode, set “Display System be called up. “Change System Settings” in the Menu” to “Enabled” (page 167). System Installer mode is set to “Disabled”.
Page 616: Responding To Displayed Error Messages
For details of the error messges displayed when using memory unit and corrective action to take for them, refer to 3-5 “Using a Memory Unit (NT631/NT631C with V1)” in page 46 or 3-6 “Using a Memory Unit (NT631/NT631C without V1)” in page 56.
Page 617 “PT Configuration” at the Support last. Initialized Memory Switch setting. settings. Tool. (Section 6 “System Menu Operation”) Press Confirm to return to the SYSTEM If the problem recurs, contact your OMRON MENU. service center. [Calendar Data Error] There is an error in the date/time...
Page 618: Errors Occurring At Start Of Operation And Their Remedies
Section 11-2 Responding to Displayed Error Messages 11-2-2 Errors Occurring during Operation and Their Remedies The table below shows the errors that can occur during operation of the NT631/NT631C and their remedies. Message Cause Remedy [Address Setting Error] The host side allocated words...
Page 619: Errors Occurring On Screen Data Initialization And Transmission
Responding to Displayed Error Messages 11-2-3 Errors Occurring on Screen Data Initialization and Transmission The table below shows the errors that can occur when the NT631/NT631C data is initialized, and during data setting and transmission, and their remedies. Message Cause...
Page 620: Errors Occurring During Operation And Their Remedies
(memory for storing the system selection of “Download System Program” and program) has reached its life. attempting to delete the system program several times, contact your OMRON service center (6-5-2 “Clearing/Installing the System Program”, page 165). Unable to download System - A communication error Select “Download System Program”...
Page 621: Communication Errors And Their Remedies
Operation When Communication Errors Occur When an error message is displayed, press the “OK” touch switch displayed on the screen. The NT631/NT631C will return to the screen that was displayed before the error occurred, and operation will restart. Display of Communication Errors...
Page 622 Check if the settings at the host for parity bit, frame conditions set incorrectly. length, communications speed, stop bit length and Framing Error flow control agree with those at the NT631/NT631C. Over-run Error The connecting cables are not Check the communication cable connection and connected correctly.
Page 623: Maintenance Of The Nt631/Nt631C
Spare PT It is advisable to have a spare NT631/NT631C available to minimize system down- time in the event of an NT631/NT631C failure or if the screen display becomes difficult to read due to deterioration of the display unit. Backlight (for NT631C only) When the backlight in the display is getting dim and the screen cannot be read eas- ily, replace the backlight.
Page 624 Section 11-3 Maintenance of the NT631/NT631C Replacing the Backlight Use the following procedure to replace the backlight. WARNING Switch OFF the NT631C power before replacing the backlight. Otherwise you could sustain an electric shock. Replace the backlight by following the procedure given below: NT631C–CFL01 (for NT631C–ST151j–E)
Page 625 Section 11-3 Maintenance of the NT631/NT631C Loosen two mounting screws, and remove the backlight. When loosening or tightening screws for backlights, be sure to use a magne- tized Phillips screwdriver. If any screw falls inside the unit, it must be extri- cated without fail.
Page 626 Section 11-3 Maintenance of the NT631/NT631C Fit the touch panel cable. Be sure to lock the connector as in step 4 after fitting. Close the rear case, and tighten four screws. Make sure that the internal cable is not trapped.
Page 627 Section 11-3 Maintenance of the NT631/NT631C [Removing and fitting the touch panel cable] S Removing the touch panel cable: Pull the arrow-marked sections up to the cable side to unlock the connector, and remove the cable. S Fitting the touch panel cable: While unlocking the connector, insert the touch panel cable fully.
Page 628 Section 11-3 Maintenance of the NT631/NT631C Engage backlight connectors at the top and the bottom respectively in place. The backlight cable has a polarity; refer to the figure below. White White Fit two touch panel cables at the top. Be sure to lock the connectors as in step 4 after fitting.
Page 629: Replacing The Battery
The NT631/NT631C uses a lithium battery to back up the memory contents. The battery life is about 5 years if the NT631/NT631C is used in a location where the ambient temperature is 25_C. If the temperature at the location of use is higher than this, the battery life will be shorter.
Page 630 The connector of the new battery must be connected within 5 minutes after dis- connecting the old battery’s connector. However, the battery can be replaced while the NT631/NT631C power is on, and in this case there is no time restric- tion.
Page 631: Inspection And Cleaning
Inspection and Cleaning 11-4 Inspection and Cleaning Clean and inspect the NT631/NT631C regularly to ensure that it is always used in its optimum condition. Cleaning Method If the display is dirty the screen is difficult to see. Clean the screen from time to time as follows.
Page 632 Inspect the following points to determine if there is any divergence from the stated criteria. If there is, either improve the surrounding environment so that the values fall within the stated range, or adjust the NT631/NT631C, for example by re-tightening screws.
Page 633: Appendices
..... Differences between the NT620S/NT620C/NT625C and the NT631/NT631C ... . .
Page 634: Specifications
EC directivesd Low voltage directive 73/23/EEC Applicable EC EN50081-2: 1993 directives or standards Standards EN61131-2: 1995 Electrical safety EN61131-2: 1995 The NT631/NT631C may not be used at a location where it is exposured to splashing oil for a long period.
Page 635: Performance Specifications
Lit in orange : Low battery voltage (during operation) Flash in red : Low battery voltage (when NT631/NT631C is stopped) *1 Time taken for brightness to reduce to half at normal temperature and humidity *2 Sharp brightness adjustment is not available.
Page 636 Specification Programming System Programming support software Programming support software NT-series Support Tool for Windows 95/98 (Ver. 3.0), made by OMRON Personal Computer Use a personal computer which can run Microsoft Window 95 or 98 Programming Tool RAM : At least 32 M bytes...
Page 637 APPENDIX A Specifications Display Capacity Item Specification Fixed character data (character strings registered for each screen) Character displays (fixed Maximum combined total with other fixed display elements of 65535 per screen display) (maximum of 524280 for an overlapping screen) Character string displays Up to 256 per screen (1024 for an overlapping screen) (40 bytes per string) Numeral displays Up to 256 per screen (1024 for an overlapping screen), max.
Page 638 9020: Programming console function screen 9999: Return to the previous screen By transmitting screen data created using the Support Tool to the NT631/NT631C Screen registration method By transmitting screen data stored in a memory unit to the NT631/NT631C (automatic/manual) Screen saving method...
Page 639 S Restrictions on data reading With NT631/NT631C, the maximum quantity of data that can be read simultaneously is fixed, and elements that exceed this data quantity limit are not displayed on the screen. Note that even if the same data is read from differ- ent elements, each instance is counted separately.
Page 640 None S Restrictions due to element coefficients The NT631/NT631C uses “element coefficients” to manage display elements. The maximum number of display coefficients that can be used at the same time is 1024. If the total of the element coefficients on a screen exceeds 1024, the elements after this total has been reached are not displayed.
Page 641 The communication flag to the PC (BAT LOW) comes ON (1). Retains the contents of the numeral/character string memory tables (i.e., they are not initialized) when the power is turned ON, when the NT631/NT631C is reset, and when Resume function the operation mode is changed.
Page 642 APPENDIX A Specifications Item Specifications Downloads the system program from the system installer System program transmission Downloads/Upload the system program with a memory unit. - Function for downloading screen data to and uploading screen data fromn the Transmission Screen data Support Tool functions transmission...
Page 643: Communications Specifications
APPENDIX A Specifications Communications Specifications S For a Host Link (RS-232C Type) Item Specification Communications standard EIA RS-232C Start-stop synchronization Communications speed: 9600, 19200 bps Communications settings Data length: 7 bits Stop bit: 2 bits Parity: Even Connector 9-pin D-SUB connector (female) (serial port A, B) Number of units connected Transmission distance Max.
Page 644 APPENDIX A Specifications S For an NT Link (1:1, RS-422A Type) Item Specification Communications standard EIA RS-422A Connector Terminal block (serial port B) Number of units connected Transmission distance Max. 500 m S For an NT Link (1:N, RS-232C Type) Item Specification Communications standard...
Page 645 APPENDIX A Specifications S For a Memory Link (RS-422A Type) Item Specification Communications standard EIA RS-422A Start-stop synchronization Communications speed: 1200, 2400, 4800, 9600, 19200, 38400bps Data length: 7, 8 bits Communications settings Stop bit: 1, 2 bits Parity: None, even, odd Flow control: None, XON/XOFF Response:...
Page 646: Dimensions
APPENDIX B Dimensions APPENDIX B Dimensions Body 302.5 (11.91) POWER 237.5 (9.35) 250 (9.84) 7.5 (0.30) 54 (2.13) 315 (12.40) With memory unit installed Units: mm (inch) (NT-MF261) 237.5 (9.35) 7.5 (0.30) 74 (2.91)
Page 647 APPENDIX B Dimensions Mounting Dimensions Mounting panel Mounting fixture POWER 140 (5.51) 259 (10.20) 15.5 (0.61) 7.5 (0.30) 240 (9.45) 34 (1.34) (min.) 38 (1.5) (max.) Units: mm (inch) 324 (12.76)
Page 648 APPENDIX B Dimensions Cable Connection Dimensions (with NT-MF261) 35 (1.38) 96 (3.78) RESET 91 (3.58) 20.4 (0.94) PRINTER PORT B PORT A 31 (1.22) 75 (2.95) 118 (4.65) Units: mm (inch)
Page 649: Using An Rs-232C/Rs-422A Convertor Unit
APPENDIX C Using an RS-232C/RS-422A Convertor Unit APPENDIX C Using an RS-232C/RS-422A Convertor Unit This section outlines the external dimensions, procedure for mounting and removal, and specifications of an RS-232C/RS-422A convertor unit (NT-AL001). Refer to this information when designing the control panel. For details, refer to the instruction manual supplied with the NT-AL001.
Page 650 APPENDIX C Using an RS-232C/RS-422A Convertor Unit Mounting to a DIN Rail Latch the top part of the rear face of the convertor unit (“a” in the figure) onto the top edge of the DIN rail, and push the unit in the direction indicated by “b” in the figure. Now fit end plates at the right and left of the convertor unit to secure it and ensure that it cannot shift laterally.
Page 651: Specifications
APPENDIX C Using an RS-232C/RS-422A Convertor Unit Specifications The general specifications and communications specifications of the convertor unit are shown below. General Specifications Item Specification Dimensions 30 (W) 114 (H) 100.2 (D) mm: with the RS-422A terminal block cover closed 30 (W) 114 (H) 119.5 (D) mm: with the RS-422A terminal block cover open...
Page 652: Dip Switch Settings
APPENDIX C Using an RS-232C/RS-422A Convertor Unit DIP Switch Settings The convertor unit has 6 digits DIP switch for setting the RS-422A/485 communication conditions. Before connecting the cable to the convertor unit, make the DIP switch settings. (Factory settings) om on 1 2 3 4 5 6 NT–AL001 [SW1-1] Not used (always ON)
Page 653: Pin Arrangement
APPENDIX C Using an RS-232C/RS-422A Convertor Unit S Do not set both SW1-5 and SW1-6 ON at the same time. This may damage in- Notice ternal circuits. S The power supply to the device supplying +5 V must be turned OFF before start- ing wiring work.
Page 654: Block Diagram
APPENDIX C Using an RS-232C/RS-422A Convertor Unit RS-232C Connector Connector Signal direction Signal name Abbreviation (convertor unit ⇔ RS-232C device) pin No. Not used – – ← Send data → Receive data ← Request to send (shorted to CS internally) →...
Page 655: Transporting And Storing The Nt631/Nt631C
Transporting and Storing the NT631/NT631C APPENDIX D Transporting and Storing the NT631/NT631C S When transporting the NT631/NT631C, use the packaging intended for it. S When storing the NT631/NT631C, observe the following conditions. Storage ambient temperature: −20 to +60_C Storage ambient humidity:...
Page 656: Making The Cable
APPENDIX E Making the Cable APPENDIX E Making the Cable The procedure for making up the cable is described below. Also refer to this procedure for making a connecting cable for use with RS-422A/485 type connections. Cable Preparation The preparation of the cable differs according to whether or not the shielding wire is to be connected to the FG. S Cable with shielding wire connected to FG (1) Cut the cable to the required length.
Page 657: Soldering
APPENDIX E Making the Cable S Cable with shielding wire not connected to FG (1) Cut the cable to the required length. (2) Remove the external vinyl insulation from the cable with a razor blade. Take care not to damage the shielding underneath.
Page 658: Hood Assembly
APPENDIX E Making the Cable Hood Assembly Assemble the connector hood as shown below. Aluminum foil tape End connected to FG End not connected to FG...
Page 659: Making The Cable For Connecting A Pc
Use the following recommended products when making the connecting cable. Name Model Remarks Connector XM2D-2501 25-pin, made by OMRON, for personal computer side XM2A-0901 9-pin, made by OMRON, for PT side Connector hood XM2S-2511 25-pin, made by OMRON, for personal computer side...
Page 660: Making The Cable For Connection To A Bar Code Reader
+5 V When using the +5 V output of serial port A of the NT631/NT631C, limit the cable length to within 2 m. If a cable longer than 2 m is used, connect an external power supply to the bar code reader.
Page 661: Making The Cable For Connection To A Printer
Making the Cable for Connection to a Printer The following product is recommended as the cable for connecting a printer. NT-CNT121 (made by OMRON, cable length 1.5 m, 20-pin – 36-pin) Refer to the following when making a cable for connection to a printer.
Page 662: Compatibility With Screen Data Of Other Pt Models
Compatibility with Screen Data of Other PT Models The screen data of the NT631/NT631C does not have complete upward compatibility with the screen data for earlier PT models. Consequently, when the data for an earlier PT model is converted for an NT631/NT631C use, partial modification may be necessary.
Page 663: Differences Between The Nt620S/Nt620C/Nt625C And The Nt631/Nt631C
NT631/NT631C are indicated below. Here, the explanation is subjected to the NT631/NT631C with “V1”. For de- tails of the differences between the NT631/NT631C without “V1” and the NT631/NT631C with “V1”, refer to “Differ- ences between the NT631/NT631C without “V1” and the NT631/NT631C with “V1” (page 663). For details of the difference in function, refer to 1-2 “Functions of the NT631/NT631C”...
Page 664 APPENDIX I Compatibility with Screen Data of Other PT Models Item NT620S/NT620C/NT625C NT631/NT631C PT status notify area Word Word Numeral/character string memory table number Word m Word m Screen number (4 BCD digits) (BCD or hexadecimal 4 digits) Numeral/character string memory table number...
Page 665 (if NT620S/NT620C/NT625C data in which table setting simultaneous operation is specified is converted for use with an NT631/NT631C, only the alarm history recording operation is performed). Memory Numeral/character string type: Numeral/character string type:...
Page 666 APPENDIX I Compatibility with Screen Data of Other PT Models Item NT620S/NT620C/NT625C NT631/NT631C Overlapping When the touch switch/lamp goes ON/OFF, the fixed display is Even if the touch switch/lamp goes ON/OFF, the fixed display is displayed in XOR inverse color of ON/OFF color of touch switch/lamp always displayed in the specified color.
Page 667: Differences Between The Nt631/Nt631C Without "V1
APPENDIX I Compatibility with Screen Data of Other PT Models Differences between the NT631/NT631C without “V1” and the NT631/NT631C with “V1” Item NT631/NT631C (without V1) NT631/NT631C (with V1) Drowing Display Object Types Display Object Types order of objects Image/library lamp...
Page 668 APPENDIX I Compatibility with Screen Data of Other PT Models Item NT631/NT631C (without V1) NT631/NT631C (with V1) Window None control area Word Global window Word k Screen No. (4-digit BCD or hexadecimal) Global window Word k+1 X coordinate (4-digit BCD or hexadecimal)
Page 669: Relationship Between System Program And Hardware
NT631C-ST151j-E (System programs supplied with NT-ZJ3PC1 -EV2/ZJ3DV1-EV2/ZJCMX1-EV2) S System programs for NT631-ST211j-EV1/NT631-ST141j-EV1/NT631-ST151j-EV1 (System programs sup- plied with NT-ZJ3MX1- EV3/ZJCMX1-EV3) These system programs have mutual compatibility, therefore, they can be installed and used for NT631-ST211j-E/ NT631C-ST141j-E/NT631C-ST151j-E/NT631-ST211j-EV1 NT631C-ST141j-EV1/NT631C-ST151j-EV1 each. However, there will be a limitation on function depending on the combination. Refer to the following table.
Page 670: Model List
APPENDIX J Model List APPENDIX J Model List Model Specification NT631-ST211-EV1 High-intensity EL display (yellow), ivory NT631-ST211B-EV1 High-intensity EL display (yellow), black NT631C-ST141-EV1 STN color display, ivory NT631-ST141B-EV1 STN color display, black NT631C-ST151-EV1 High-intensity STN color display, ivory NT631C-ST151B-EV1 High-intensity STN color display, black...
Page 671: Cpus (For Connection Via A Host Link)
APPENDIX J Model List CPUs (For Connection via a Host Link) Model Specification PC Type CPM1-10CDR-j RS-232C adapter/RS-422A adapter connected to the peripheral C-series CPM1-20CDR-j port CPM1 CPM1-30CDR-j CPM1A-10CDj-j CPM1A-20CDj-j CPM1A-30CDj-j CPM1A-40CDj-j CQM1-CPU21-E Features a 9-pin connector for RS-232C connections C-series CQM1-CPU41-EV1 CQM1...
Page 672: Cpus (For Connection Via An Nt Link (1:1))
APPENDIX J Model List CPUs (For Connection via an NT Link (1:1)) Model Specification PC Type CPM1-10CDR-j RS-232C adapter connected to the peripheral port C-series CPM1-20CDR-j (RS-422A adapter cannot be used) CPM1 CPM1-30CDR-j CPM1A-10CDj-j CPM1A-20CDj-j CPM1A-30CDj-j CPM1A-40CDj-j CQM1-CPU41-EV1 Features a 9-pin connector for RS-232C connections C-series CQM1-CPU42-EV1 CQM1...
Page 673: Cpus (For Connection Via An Nt Link (1:N))
RS-422A: 8-pin terminal block RS-232C Adaptor, RS-422A Adaptor Model Specification CPM1-CIF01 Links the RS-232C port of an NT631/NT631C and the peripheral port of a CPM1 (compatible with host link, and NT link (1:1)) CPM1-CIF11 Links the RS-422A port of an NT631/NT631C and the...
Page 674: Related Parts And Equipment For Pt
CD–ROM Options NT631C-CFL01 Replaceable backlight (for NT631C-ST151j-EV1) NT631C-CFL02 Replaceable backlight (for NT631C-ST141j-EV1) NT610C-KBA04 Reflection suppressing protective sheet for NT631/NT631C NT625-KBA01 Chemical–resistant cover for NT631/NT631C NT-MF261 Memory unit for NT631/NT631C 3G2A9-BAT08 Spare battery The Support Tool indicated above includes the system installer and the standard system programs for the NT31, NT31C, NT631, and NT631C.
Page 675 9-pin type, inch pitch screw, made by OMRON DB-C2-J9 25-pin type, made by JAE Printer Cable Model Specification NT-CNT121 Printer cable for half pitch (1.5 m), made by OMRON Cable for peripheral port of CS1-series PLC Model Specification CS1W-CN118 Made by OMRON...
Page 676: Option List
APPENDIX K Option List APPENDIX K Option List Replaceable Backlights ... NT631C-CFL01 (for NT631C-ST151j) These are backlights for NT631C for replacement purposes. Two pieces make a set. Replaceable Backlights ... NT631C-CFL02 (for NT631C-ST141j) Protective Sheet ... NT610C-KBA04 Stuck to the display to prevent irregular reflection or contamination. The entire sheet is colorless and transparent. The five sheets make a set.
Page 677 APPENDIX K Option List Chemical-resistant Cover ... NT625-KBA01 Covers the front panel and protects it from various chemical agents. The entire sheet is milky white and made of silicone rubber. The sheet offers protection against the following chemical agents. Protects against Does not protect against Boric acid Hexane...
Page 678 This is a lithium battery used for memory backup. Memory Unit ... NT-MF261 This is a dedicated unit for reading/writing the screen data and the system programs in an NT631/NT631C. Data is transmitted by DIP switch setting at the memory unit.
Page 679: Pc Memory Map
APPENDIX L PC Memory Map APPENDIX L PC Memory Map OMRON C-Series PC, SRM1 Memory Map <Host Link / NT Link (1:1) / NT Link (1:N)> Extended Timer/Counter Data Memory Relay Area Holding Auxiliary Link Relays Data Memory Present Area...
Page 680: Omron Cvm1/Cv-Series Pc Memory Map
APPENDIX L PC Memory Map OMRON CVM1/CV-Series PC Memory Map <Host Link> Extended Timer/Counter Data Memory Relay Area Holding Auxiliary Link Relays Data Memory Present Area (Current (CIO) Relays (HR) Relays (AR) (LR) Values (DM) Bank) (TIM/CNT) (EM) CV500 00000 to...
Page 681: Keycode Tables
Appendix M Keycode Tables APPENDIX M Keycode Tables ISO 8859/1 ° Ð ð ’ À à Space Space NBSP ± ¡ Á Ñ á ñ Space Space ” ¢ Â Ò â ò Space Space £ Ã Ó ã ó Space Space ¤...
Page 682: Ms-Dos Cp437
Appendix M Keycode Tables MS–DOS CP437 α ≡ ’ Ç É á β ± ü æ Í Γ ≥ ” é Æ ó π ≤ â ô ú Σ ⌠ ä ö ñ σ ⌡ à ò Ñ µ ÷ &...
Page 683: Index
INDEX Bit memory table read command ... . Bit memory table write command ... . Alarm history ......Bit memory tables .
Page 685 ......... . Errors in the system installer mode and their Differences between the NT631/NT631C and the remedies .
Page 686 Host link ........Lamps ........Host link method .
Page 687 ....... . NT631/NT631C and RS–232C at the host ..
Page 688 Principal functions of NT631/NT631C ..PT status notify area ..... . .
Page 689 ........Serial port A connector .
Page 690 Storage type and stored data ....Using a Memory Unit(NT631/NT631C with V1) Storage type for the BCD format ... .
Page 691 Zero suppression ......
Page 692: Revision History
Revision History A manual revision code appears as a suffix to the catalog number on the front cover of the manual. Cat. No. V044-E1-2 Revision code The following table outlines the changes made to the manual during each revision. Page numbers refer to the previous version.

This manual is also suitable for:

Nt631c

Omron NT631 Operation Manuals

Table of Contents

Precautions

1 Intended Audience

2 General Precautions

3 Safety Precautions

General

Section 2 Preparing for Connection

Section 3 Hardware Settings and Connections

Hardware Settings and Connections

Connecting to the Host from the RS-232C Port

Section 5 Connecting to the Host from the Rs-422A/485 Port

Section 6 System Menu Operation

Section 7 Nt631/Nt631C Functions

Section 8 How to Use the Pt

Section 11 Troubleshooting and Maintenance

Appendices

APPENDIX A Specifications

APPENDIX B Dimensions

APPENDIX C Using an RS-232C/RS-422A Convertor Unit

APPENDIX D Transporting and Storing the NT631/NT631C

APPENDIX E Making the Cable

APPENDIX F Making the Cable for Connecting a PC

APPENDIX G Making the Cable for Connection to a Bar Code Reader

APPENDIX H Making the Cable for Connection to a Printer

APPENDIX I Compatibility with Screen Data of Other PT Models

APPENDIX J Model List

APPENDIX K Option List

APPENDIX Lpc Memory Map

APPENDIX M Keycode Tables

Index

Quick Links

Chapters

Troubleshooting

Related Manuals for Omron NT631

Summary of Contents for Omron NT631