Panasonic WV-SFV481 Installation Manual page 2

The installation tasks are explained using 4 steps.
Step1 Step2
Mount the brackets to a ceiling or
Make sure all items are prepared
before beginning installation. wall
Step1 Preparations
There are 4 methods to install the camera to a ceiling or wall as described below. Prepare the
required parts for each installation method before starting the installation. The following are the
requirements for the various installation methods.
Recommended Minimum pull-out
Installation method
screw
[1] Mount the camera on the two-gang junction
M4 screws x 4 196 N {44 lbf}/1 pc.
box using the A attachment plate (accessory).
[2] Directly mount the camera onto the ceiling or
wall using the attachment plate (when wiring M4 screws x 4 196 N {44 lbf}/1 pc.
can be installed in the ceiling or wall).
[3] Mount the camera onto the ceiling or wall using
the B base bracket (accessory) (when conduits
M4 screws x 4 196 N {44 lbf}/1 pc.
are used for wiring, or when there is no space
available for wiring in the ceiling or the wall). *1
[4] When installing on a ceiling using the
WV-Q121B (ceiling hanging mount bracket) M10 screws x 4 1411 N {317 lbf}/1 pc.
and WV-Q124 (suspension mount bracket). *1*2
[5] When installing on a wall and pole using the
WV-Q122A (wall mount bracket) and WV-Q124
M10 screws x 4 823 N {185 lbf}/1 pc.
(mount bracket) *1 *3
*1 Use 4 screws (M4 x 8 mm, accessory) to fix the A attachment plate (accessory) to the
B base bracket (accessory) or WV-Q124.
*2 For information on the procedure for attaching the WV-Q121B and WV-Q122A with the
WV-Q124, refer to the operating instructions included with the respective attachment brackets.
*3 For information on the procedure for attaching the WV-Q122A with the WV-Q124, refer to
the operating instructions included with the respective attachment brackets.
[4] [5]
WV-Q122A
WV-Q121B
WV-Q124
Camera
[3] Mount the camera to a ceiling or a wall using base bracket
<Mounting the base bracket>
The B base bracket (accessory) can be fixed in any of the following 6 screwing positions
according to ceiling and wall conditions. Match the hole used when installing the camera to
any of positions A to F.
Position A Position B Position C
85 mm {3-11/32 inches}
(85.7 mm {3-3/8 inches})
138 mm ø25.4 mm
85 mm {5-7/16 inches} {ø1 inch} *3
ø25.4 mm 83.5 mm
{3-11/32 inches}
{ø1 inch} *3 {3-9/32 inches}
(85.7 mm
{3-3/8 inches})
138 mm
{5-7/16 inches}
Position D Position E Position F
*4
63 mm
{2-15/32 inches}
83.5 mm ø25.4 mm
{3-9/32 inches} {ø1 inch} *3
63 mm
ø25.4 mm
70 mm
{2-15/32 inches}
{ø1 inch} *3
{2-3/4 inches}
*3 The wiring hole diameter is 25.4 mm {1 inch}. Select any of the 2 base bracket fixture holes
of E template B (for the base bracket, accessory) when installing the base bracket.
*4 When attaching the base bracket to a one-gang junction box in Position E, secure the base
bracket with 2 screws (M4, locally procured).
<Making holes and wiring from the back side of a ceiling or wall>
● Mount the B base bracket
Fixing screws(M4 x 4, locally B Base bracket (accessory)
(accessory) to a ceiling or wall
procured)
using 4 fixing screws (M4,
Minimum pull-out strength:
locally procured). Refer to the 196 N {44 lbf} (per 1 pc.)
installation example on the
right and pass the wiring
through the base bracket.
● Secure A attachment plate
(accessory) to base bracket A Attachment plate
(accessory)
using 4 C attachment fixing
screws (accessory).
(Recommended tightening C Fixing screws for attachment
plate: x 4 (accessory)
torque: 0.78 N·m {0.58 lbf·ft})
(Recommended tightening
torque: 0.78 N·m {0.58 lbf·ft})
Installation
Step3
Connect cables, and then attach the
camera to the mount bracket.
IMPORTANT:
● Procure 4 screws (M4) to secure the A attachment plate (accessory) or B base
bracket (accessory) to a ceiling or a wall.
● When mounting the camera on a concrete ceiling, use an AY plug bolt (M4) for
securing. (Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
● Select screws according to the material of the ceiling or wall that the camera will be
strength mounted to. In this case, wood screws and nails should not be used.
● If a ceiling board such as plaster board is too weak to support the total weight, the
area shall be sufficiently reinforced.
Step2 Fixing the brackets
[1] Using a two-gang junction box
[2] Directly mount the camera to the ceiling or wall using the attachment plate
Note:
● The direction of " TOP" on the A attachment plate (accessory) determines the upwards
direction of the image on the PC monitor.
● When mounting on a ceiling, determine the direction that you want images to be dis-
played upwards on the PC monitor, and then mount so that the A attachment plate
(accessory) aligns with " TOP" on D template A (for the attachment plate, accessory).
● When installing on a wall, attach the A attachment plate (accessory) so that " TOP"
faces upward.
46 mm
83.5 mm
46 mm
{1-13/16
{3-9/32
{1-13/16 inches} inches}
inches}
Two-gang
junction box
TOP
TOP
WV-Q124
TOP
A Attachment
plate (accessory)
Camera
Fixing screws
Fixing screws (4 pcs., locally procured)
(4 pcs., locally procured)
<Wiring using a ceiling or wall conduit>
A Remove the cap for the female thread for the
conduit by using a hexagon wrench (ISO 2936,
width across flats S=5 mm {3/16 inches}).
The female thread for conduit is compliant with
ANSI NPSM (parallel pipe threads) 3/4 inches or
G3/4 of ISO 228-1.
Cap for the female
* When making holes and wiring from
46 mm
thread for the
{1-13/16 inches}
a ceiling or wall, do not remove the
conduit
cap for the female thread for the
ø25.4 mm conduit.
{ø1 inch} *3
B Attach the base bracket and attachment
plate to a ceiling or wall.
● Mount the B base bracket
(accessory) to a ceiling or wall
Base bracket
B
using 4 fixing screws (M4, locally
(accessory)
procured). Refer to the installation
example on the right and pass the
108.5 mm
{4-9/32 inches}
wiring through the base bracket.
● Secure A attachment plate
ø25.4 mm (accessory) to base bracket using
{ø1 inch} *3
4 C attachment fixing screws
Conduit
(accessory). (Recommended
tightening torque: 0.78 N·m
{0.58 lbf·ft})
C Fixing screws for attachment plate: x 4 (accessory)
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
IMPORTANT:
● If open wiring is conducted, be sure to use conduits and run the cables inside the tubes to
protect the cables from direct sunlight.
● Installation work shall be such that there is no exposure to water into the architecture
through the conduits having been joined.
Note:
● Make sure to attach the A attachment plate (accessory) so that the " TOP" mark faces
in the opposite direction of the cap for the female thread for the conduit.
● The direction of " TOP" on the A attachment plate (accessory) determines the upwards
TOP
direction of the image on the PC monitor. Determine the direction that you want images to
be displayed upwards on the PC monitor, and then align the direction of the B base
bracket (accessory).
● When installing on a wall, attach the A attachment plate (accessory) so that " TOP"
faces upward.
Step3 Mount the camera to the attachment plate
A Check the position of attachment
mounting screws on the bottom side
of the camera.
Step4
Adjust the direction of the image.
Attachment mounting screws
Protruding part
* This illustration shows the
camera after being rotated.
Note:
● After the cables have been connected to the camera, align the direction of the Panasonic logo
on the camera with " TOP" of the A attachment plate (accessory). Align the OPEN mark of
83.5 mm
the enclosure side panel with the protruding part of the B base bracket (accessory), insert
{3-9/32 inches}
3 attachment mounting screws into the attachment plate, rotate the camera approximately 15°, and
move the LOCK mark to the protruding part of the base bracket to temporarily secure the camera.
Cable access hole
(When directly attaching the attachment plate to a ceiling or wall, align the OPEN mark to the
(ø30 mm
hook part of the attachment plate.)
{ø1-3/16 inches})
IMPORTANT:
D Template A (for the
attachment plate, accessory) ● Disconnect the 12 V DC power source and PoE power source to prevent power from being
supplied during mounting work.
A Attachment plate
● Because the sub cover is attached to the camera with the sub cover sheet, do not remove
(accessory)
the sub cover.
● For installations on the wall, to prevent water from accumulating on the surface of the
dehumidifying device, install the camera so that the dehumidifying device does not face up.
If water accumulates on the surface of the dehumidifying device, it cannot function properly.
Step4 Adjustment
B Base bracket (accessory)
A Loosen the SD memory card slot cover fixing
screw on the side of the camera using the
G bit (accessory), and open the SD memory
card slot cover.
B Turn on the camera. The LINK indicator
inside the SD memory card slot cover lights.
Make sure that the ACT indicator is blinking.
(Refer to the descriptions in "Major operat-
ing controls" for more information about the
indicators.)
* After turning on the camera, there may be
a sound produced from the lens for several
x
Fixing screws (M4 4, locally procured) seconds. This is not a malfunction.
Minimum pull-out strength: C Perform camera settings while referring to the
196 N {44 lbf} (per 1 pc.) included "Configure the settings of the cam-
era" (leaflet), and check if camera images are
displayed on the PC monitor.
SD memory card slot
SD memory card
cover fixing screw
slot cover
TOP
A Attachment
plate
(accessory)
* Part of the sub cover is not shown.
B Connect cables to the camera according to the C Loosen 2 sub cover fixing screws using
instructions in "Making connections", and mount the the G bit (accessory).
camera by inserting the attachment mounting screws
into the holes of the A attachment plate (accessory).
Protruding part Sub cover
TOP
A Attachment plate
(accessory) holes x 3
Sub cover fixing screws
Hook part (attachment plate)
<When attaching the attachment
plate directly to a ceiling or wall>
D Remove the cover film from the dome cover F Insert an SD memory card into the slot, if
surface. necessary.
E Align the upwards direction of the image
● Insert the SD memory card with its label
while rotating the image rotation gear and
facing down.
checking the image on the PC monitor.
G Close the SD memory card slot cover,
and tighten the SD memory slot cover slot
Rotate the image rotation gear using the
cover fixing screw to secure the cover.
included bit, and align the upwards direction
of the image as necessary. (Recommended tightening torque:
Rotating the image rotation gear clockwise 0.78 N·m {0.58 lbf·ft})
also rotates the PC image clockwise. Rotating
the image rotation gear counterclockwise also
SD memory card
rotates the PC image counterclockwise.
slot cover
Adjustable range of the PC image:
-45° to +45°
● The default position of the image rotation
gear is 0°.
● When using Double Panorama, if the
image rotation gear is in its default
position, images are display at a 45°
angle. If you want to divide Double
Panorama images horizontally or
vertically, adjust the image rotation gear.
Adjustments to the image rotation gear are
applied to all image capture modes,
including Double Panorama. * Part of the sub cover is not shown.
Note:
● To remove the SD memory card, hold
● When Double Panorama or down the SD ON/OFF button for about
Panorama is selected for the image
2 seconds. When the SD MOUNT indicator
capture mode, you can rotate the
goes out, you can remove the SD memory
image at 90° intervals by using pre-
card.
set position settings. To make further
● After the SD memory card has been
fine adjustments to the image angle,
replaced, press the SD ON/OFF button,
adjust the image rotation gear. Refer
and make sure the SD MOUNT indicator
to 11.1 and 11.5.4 of the Operating
is continually lit.
Image rotation gear Instructions for more information.
● If you do not press the SD ON/OFF
button after replacing the SD memory
Note:
card, the SD MOUNT indicator is
Take care of the following points when
Image rotation
continually lit approximately 5 minutes
gear using monitor out.
later.
● Select "9M Fisheye" or "4M Fisheye"
for "Image capture mode".
● Locally procure the ø3.5 mm monau-
G Bit
ral mini plug RCA pin jack conver-
(accessory)
sion cable.
● Select the [Setup]→[Basic] tab, and
then select On (NTSC) or On (PAL)
for [Monitor out].
D Remove the sub cover from the camera,
and secure the camera using camera fixing
screws. (Recommended tightening torque:
0.78 N·m {0.58 lbf·ft})
Sub cover
Camera fixing screw
Sub cover sheet
IMPORTANT:
● Be sure to tighten the camera fixing
screw. Failure to observe this may
cause camera trouble due to camera
falling. (Recommended tightening
torque: 0.78 N·m {0.58 lbf·ft})
H Return the sub cover to its original position
and secure it using 2 sub cover fixing
screws. (Recommended tightening torque:
0.78 N·m {0.58 lbf·ft})
SD memory card slot cover
SD memory card fixing screw
slot cover
SD memory card
Sub cover
Sub cover fixing screws
IMPORTANT:
● Ensure that the SD memory card slot
cover's fixing screw is firmly secured.
Failure to observe this may cause elec-
tric shock or malfunction.
● Securely tighten the 2 sub cover fixing
screws. Failure to do so may cause the
camera to drop.
● After the installation is completed, clean
the dome cover surface with a soft
cloth, etc.
● After the installation is complete, if the
image is out of focus, turn off the cam-
era, and then turn it on again. If the
image is still out of focus, select the
[Image/Position] tab from
[Setup]→[Image/Audio], and then re-
adjust the back focus from [Setup>>] of
[Back focus].
* When removing the camera, perform
removal by following the installation pro-
cedure in the reverse order.