Panasonic WV-SFV481 Installation Manual

Installation Guide
Included Installation Instructions
Network Camera
WV-SFV481
Model No.
● This manual describes the installation procedures, network camera installation, cable
connections, and the direction of the image adjustment.
● Before reading this manual, be sure to read the Important Information.
For U.S. and Canada: For Europe and other countries:
Panasonic System Communications Panasonic Corporation
Company of North America,
http://panasonic.net
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/ Panasonic System Networks Co., Ltd.
For customer support, call 1.800.528.6747 Fukuoka, Japan
Two Riverfront Plaza, Newark, NJ 07102-5490
Authorised Representative in EU:
Panasonic Canada Inc.
Panasonic Testing Centre
5770 Ambler Drive, Mississauga,
Panasonic Marketing Europe GmbH
Ontario, L4W 2T3 Canada
Winsbergring 15, 22525 Hamburg, Germany
(905)624-5010
www.panasonic.ca
© Panasonic System Networks Co., Ltd. 2014 PGQX1665YA Cs1114-1045 Printed in China
Major operating controls
The component names of the camera are as follows. Refer to the illustration when installing or
adjusting the camera.
<Inside view of the SD memory card slot cover (with SD memory card slot cover opened)>
ACT
SD ERROR/ABF
indicator
indicator
SD MOUNT
LINK
indicator
indicator
INITIAL SET button SD memory card slot SD ON/OFF button
<Inside view of the sub cover (with sub cover removed)>
Power/audio/
alarm cable *1
Dehumidifying device
Image rotation gear
Camera fixing screw
Network cable
SD memory card
slot cover
Data Matrix: To our
website *2
*1 The detailed specifications on the right side of this page describe each terminal and
cable.
*2 Data Matrix is our website address converted into a two-dimensional barcode. Depending
on the scanning application used, the Data Matrix may not be able to be read correctly. In
this case, access the site by directly entering the following URL.
http://security.panasonic.com/pss/security/support/qr_sp_select.html
*3 SDXC/SDHC/SD memory card is described as SD memory card.
Standard accessories
Important Information ............................... 1 pc. CD-ROM *1
Installation Guide (this document) ............ 1 set Code label
Warranty card ........................................... 1 set
*1 The CD-ROM contains the operating instructions and different kinds of tool software pro-
grams.
*2 This label may be required for network management. The network administrator shall retain
the code label.
The following parts are used during installation procedures.
A Attachment plate .................................. 1 pc. F Waterproof tape ................................... 1 pc.
B Base bracket ........................................ 1 pc. G Bit (Hex wrench, screw size
C Fixing screws for attachment plate 6.35 mm {1/4 inches} T10) .................... 1 pc.
(M4 x 8 mm) ...................................... 5 pcs. H 4P alarm cable ..................................... 1 pc.
(incl. 1 spare) I 2P power cable .................................... 1 pc.
D Template A (for the attachment plate) .... 1 sheet J LAN cable cover................................... 1 pc.
E Template B (for the base bracket) ..... 1 sheet
G
F
A Attachment plate (accessory)
Direction marker for
Camera
installation " TOP"
Enclosure
Dome cover
C Fixing screws for
attachment plate (accessory)
Sub cover
INITIAL SET button
● How to initialize the camera
Follow the steps below to initialize the network camera.
1 Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from the cam-
era. When using an external power supply, disconnect the 2P power cable plug from the camera.
2 Turn on the power of the camera while holding down the INITIAL SET button, and then keep
holding down the button for 5 seconds or more. About 2 minutes later, the camera will start up
and the settings including the network settings will be initialized.
IMPORTANT:
● When the camera is initialized, the settings including the network settings will be initialized.
Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized.
● Before initializing the settings, it is recommended to write down the settings in advance.
● Do not turn off the power of the camera during the process of initialization. Otherwise, it
may fail to initialize and may cause malfunction.
ACT indicator
● When data is being sent via the network camera
LINK indicator
● When the camera is able to communicate with the
connected device
SD ERROR/ABF indicator
● When ABF (Auto Back Focus) operation is being executed
● When the set is being started
● When an SD memory card* 3 is recognized normally
● When the SD memory card slot is not used or an abnormality
is detected in SD memory card after the camera has started
SD MOUNT indicator
● When an SD memory card is inserted and could
be recognized
*1
● When data can be saved after the SD memory card is
inserted and the SD ON/OFF button is pressed
● When data can be saved to the SD memory card
● When the SD memory card is removed after holding down
the SD ON/OFF button for about 2 seconds
● When data cannot be saved to the SD memory card because
an abnormality was detected or the SD memory card is
configured not to be used
SD ON/OFF button
1 When the SD ON/OFF button is pressed, data can be saved to the SD memory card.
2 When the SD ON/OFF button is held down for about 2 seconds, the SD MOUNT indicator
goes out, and the SD memory card can be removed.
Note:
● The ACT indicator, Link indicator, SD ERROR/ABF indicator, and SD MOUNT indicator
inside the SD memory card slot cover can be turned off. (Indicators are set to light or blink
in the default settings.)
Turn off the indicators as required according to the installation environment. (☞ Operating
Instructions (included in the CD-ROM))
Making connections
Turn off each system's power supply before making a connection. Before making connections,
................................................. 1 pc.
prepare the required peripheral devices and cables.
*2 .............................................. 1 pc.
Connect a LAN cable
IMPORTANT:
● Use all 4 pairs (8 pins) of the LAN cable (category 5 or better, straight, STP).
● The maximum cable length is 100 m {328 feet}.
● Make sure that the PoE device in use is compliant with IEEE802.3af standard.
● When connecting both the 12 V DC power supply and the PoE device for power
supply, 12 V DC will be used for power supply*.
* If a 12 V DC power supply and a PoE hub or router are used at the same time,
network connections may not be possible. In this case, disable the PoE settings.
Refer to the operating instructions of the PoE hub or router in use.
* Depending on the PoE device used, if you stop the 12 V DC power supply after
operating it and a PoE hub or router at the same time, the power supply may stop,
causing the camera to restart.
● When the LAN cable is disconnected once, reconnect the cable after around 2 seconds.
When the cable is quickly reconnected, the power may not be supplied from the PoE
device.
● When cables are used outdoors, there is a chance that they may be affected by
lightning. In this case, install a lightning arrester just before where the cables con-
nect to the camera.
(Hex wrench, screw size
6.35 mm {1/4 inches} T10)
RJ45 (female)
B Base bracket (accessory)
Network cable
Alarm input/output cable
Microphone/line input cable
Connect a stereo mini plug (ø3.5 mm).
● Input impedance: Approx. 2 kΩ (unbalanced)
● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)
● Recommended microphone: Plug-in power type (option)
•Supply voltage: 2.5 V ±0.5 V
•Recommended sensitivity of microphone: -48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
● Input level for the line input: Approx. -10 dBV
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera with cables
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are
not waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to ap-
ply waterproof treatment in the following procedure. Failure to observe this or use of a tape other
than the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting in
malfunction.
<LAN cable>
Blinks green (accessing)
Lights orange
Wind the tape in a
half-overlapping manner.
Blinks red (Interval of 1 time/ second) Wind the tape in a
half-overlapping manner.
Lights red
Lights red → Lights off
Lights red → Stays red IMPORTANT:
How to wind the supplied waterproof tape
● Also waterproof the I 2P power cable (accessory),
H 4P alarm cable (accessory), and external connec-
Lights off → Blinks green →
Lights off tions in the same way.
Lights off → Lights green
● Stretch the tape to approx. twice its length (see the
illustration) and wind it around the cable. Insufficient
Lights green
tape stretch causes insufficient waterproofing.
Lights green → Blinks green → Lights off (recording)
● To prevent the LAN cable hook from coming loose
Lights green → Lights off (waiting for recording)
easily, fit the J LAN cable cover (accessory) onto the
Lights off
pigtail cable as illustrated, and then slide it in the
direction indicated by the arrow.
The connector of the LAN cable used with this cam-
era must meet the following restrictions.
Height when inserted (From bottom to hook.):
Max. 16 mm {5/8 inches}
Connector width: Max. 14 mm {9/16 inches}
● To install this product outdoors, be sure to waterproof
the cables. Waterproof grade (IEC IP66 or equiva-
lent) is applied to this product only when it is installed
correctly as described in these operating instructions
and appropriate waterproof treatment is applied. The
internal parts of B base bracket (accessory) are not
waterproofed.
Connect the alarm input/output cable
H 4P alarm cable (accessory)
<Ratings>
• ALARM IN1(DAY/NIGHT IN), ALARM IN2, ALARM IN3
Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF:
ON:
• ALARM OUT, AUX OUT
Output specification: Open collector output (maximum applied voltage: 20 V DC)
Open:
Close:
* The default of EXT I/O terminals is "Off".
IMPORTANT:
● Be sure to use the H 4P alarm cable (accessory) provided with this product.
● Install external devices so that they do not exceed the ratings above.
● When using the external I/O terminals as the output terminals, ensure they do not
cause signal collision with external signals.
Note:
● Off, input, and output of the external I/O terminal 2 and 3 can be switched by config-
uring the setting. Refer to the Operating Instructions on the provided CD-ROM for
further information about the external I/O terminal 2 and 3 (ALARM IN2, 3) settings
("Off", "Alarm input", "Alarm output" or "AUX output").
LAN cable
(category 5 or better, straight) Connect the power cable
Caution:
H 4P alarm cable
● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL
(accessory)
BE INCORPORATED TO THE EQUIPMENT POWERED
BY 12 V DC POWER SUPPLY.
● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL
12 V DC (red)
1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/
GND (black)
Power cable UL/CSA 60950-1).
I 2P power cable (accessory)
(12 V DC)
Connect the output cable of the AC adaptor to the I 2P power cable (accessory).
IMPORTANT:
Microphone/line input cable (white)
● Use 12 V DC power supply that is insulated from the commercial AC power.
● Be sure to use the I 2P power cable (accessory) provided with this product.
● Be sure to fully insert the I 2P power cable (accessory) into the 12 V DC power
Audio/monitor output cable (black)
supply terminal. Otherwise, it may damage the camera or cause malfunction.
* Can switch to monitor output
● When installing the camera, make sure that excessive force is not applied to the
power cable.
● Be sure to use an AC adaptor compliant with the specifications (written in the indication
label on the bottom side of this unit) regarding power source and power consumption.
Connect an external amplifier-embedded speaker to the audio/monitor
output cable
Connect a stereo mini plug (ø3.5 mm).*
Less than 10 m {32.8 feet} (for line input)
● Output impedance: Approx. 600 Ω (unbalanced)
● Recommended cable length: Less than 10 m {32.8 feet}
● Output level: -20 dBV (can switch to monitor output)
* Use an external powered speaker.
IMPORTANT:
● Connect/disconnect the audio cables and turn on the power of the camera after turn-
ing off the power of the audio output devices. Otherwise, loud noise may be heard
from the speaker.
● Make sure that the stereo mini plug is connected to this cable. When a monaural mini
plug is connected, audio may not be heard.
When connecting a monaural speaker with amplifier, use a locally procured conver-
sion cable (mono-stereo).
Note:
< Alarm input/output cable, power cable, microphone/
● Audio out is selected for the audio/monitor output cable by default. The cable can
line input cable, audio/monitor output cable>
be used for monitor out by selecting the [Setup] → [Basic] tab, and then selecting
[Monitor out]. (The ø3.5 mm monaural mini plug
locally procured.)
Wind the tape in a
When connecting to a network using a PoE hub
half-overlapping
Wind the tape in a
manner. half-overlapping
Before starting the installation, check the entire system configuration. The following illustration
manner.
gives a wiring example of how to connect the camera to the network via a PoE device (hub).
Powered speaker
Stretch the tape to
approx. twice its length.
2x
Microphone
* Can switch to monitor out
(select the [Setup]→
J LAN cable cover (accessory)
[Basic] tab, and then
select [Monitor out])
<Required cable>
LAN cable (category 5 or better, straight)
Use a LAN cable (category 5 or better, cross) when directly connecting the camera to a PC.
IMPORTANT:
● The analog monitor is used when servicing the camera. It is not provided for record-
ing/monitoring use.
● Depending on the monitor, some characters (camera title, preset ID, etc.) may not be
displayed on the screen.
● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
The hook engages
with the connector
● If a PoE hub is not used, each network camera must be connected to a 12 V DC
terminal
power supply.
● When using 12 V DC, power supply from a PoE hub or router is not required.
GND (black)
ALARM IN3, AUX OUT (gray) (Alarm input 3, AUX output)
ALARM IN2, ALARM OUT (red) (Alarm input 2, Alarm output)
ALARM IN1, DAY/NIGHT IN (green) (Alarm input 1/ Color-monochrome switching input)
Open or 4 V - 5 V DC
Make contact with GND (required drive current: 1 mA or more)
4 V - 5 V DC by internal pull-up
Output voltage 1 V DC or less (maximum drive current: 50 mA)
Power cable
12 V DC
Red Positive
Black Negative
RCA pin jack conversion cable is
Analog monitor PoE device (hub)
*
LAN cable
(category 5 or better, straight)
PC
LAN cable
(category 5 or
better, straight)
LAN cable
(category 5 or better, straight)