Programming Instructions; Memory Pads; Multiple Cooking Stages; X2 Quantity Feature - Amana CRC18T2OG Service Manual

Programming Instructions

Memory Pads

From the factory, this oven can of store up to 10 cooking
programs. Follow instructions below to program cooking
times and power levels for customized cooking.
Example: Program third cooking sequence to heat for 30
seconds at 80% power.
1. Open oven door.
• Display shows "READY".
• If door is closed or RESET pad is pressed before
finishing programming sequence, oven exits
programming mode.
2. Press and hold pad 1 for approximately 5 seconds.
• After 5 seconds, signal sounds. Display shows
"P:0".
3. Press 3 pad to select memory pad.
• Display shows cooking time, "COOK LEVEL" and
power level if other than 100 percent power.
4. Press 3 and 0 pad to enter desired cooking time.
5. Press POWER LEVEL pad to change power level.
• Display shows "COOK LEVEL" and current power
level if other than 100 percent power.
6. Press 8 pad to enter desired power level.
7. Press START pad to save new cooking time and
power level in oven memory.
• Display shows "P:0".
• Repeat step 3–8 to program additional pads.
8. Press STOP/RESET pad or close oven door to exit
programming mode.
Double Pad Programs
The oven control can be changed to store up to 100
cooking programs. See the "User's Options" section of
this manual to change oven control.
To create a double pad program, follow the instructions
above except for a change to step #3. When entering the
cooking program number, press 2 memory pads. For
example, press pads 0 and pad 3 to create a new
cooking program.

Multiple Cooking Stages

Follow instructions below to program oven to perform four
consecutive cooking cycles without interruption.
Example: Program third cooking sequence to heat for 30
seconds at 80% power, 40 seconds at 50% power, and
10 seconds at 100% power.
1. Open oven door.
• Display shows "READY".
• If door is closed or RESET pad is pressed before
finishing programming sequence, oven exits
programming mode.
2. Press pad 1 for approximately 5 seconds.
• After 5 seconds, signal sounds. Display shows
"P:0".
4. Press 3 pad to select memory pad.
• Display shows cooking time, "COOK LEVEL" and
power level if other than 100 percent power.
5. Press 3 and 0 to enter desired cooking time.
6. Press POWER LEVEL pad to change power level.
• Display shows "COOK LEVEL" and current power
level if other than 100 percent power.
7. Press 8 pad to enter desired power level.
8. Press TIME ENTRY pad.
• Display briefly shows "P:03
programming, pad 3, stage 2. Then cook time and
power level for stage show in display.
• Repeat steps 5–8 to create additional stages.
9. Press START pad to save new cooking time and
power level in oven memory.
10. Press STOP/RESET pad or close oven door to exit
programming mode.

X2 Quantity Feature

This feature allows the user to change the amount of time
added when the X2 pad and then the programmed pad is
pressed. Based on the original time, the X2 pad can add
from 10%-100% of additional cooking time. The default is
80%. Example: change cooking factor to 50% for third
cooking sequence.
1. Open oven door.
• If door is closed or RESET pad is pressed before
finishing programming sequence, oven exits
programming mode.
2. Press and hold pad 1 for approximately 5 seconds.
• After 5 seconds, signal sounds. Display shows
"P:--".
3. Press 3 pad to select the cooking program.
4. Press 5 pad to change cooking factor.
• Display shows "CF:05".
5. Press START pad to save changes.
6. Press STOP/RESET pad or close oven door to exit
programming mode.
Double Pad Programs
The oven control can be changed to store up to 100
cooking programs. See the "User's Options" section of
this manual to change oven control.
To change the quantity for a double pad program, follow
the instructions above except for a change to step #3.
When entering the cooking program number, press 2
memory pads. For example, press pads 0 and pad 3 to
create a new cooking program. After the program is
saved, press pad 0 and pad 3 to start a cooking program.
15
(1-4)
" indicating
RS2240002 Rev. 1