Related Manuals for Planet FSP-804P
Summary of Contents for Planet FSP-804P
- Page 1 8-Port 10/100TX Fast Ethernet Switch with 4-Port 802.3at PoE+ Injector FSD-804P User’s Manual...
-
Page 2: Fcc Warning
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred. - Page 3 Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision PLANET 8-Port 10/100TX Fast Ethernet Switch with 4-Port 802.3at PoE+ Injector User's Manual FOR MODEL: FSD-804P REVISION: 4.0 (November 2016)
-
Page 4: Table Of Contents
Table of Contents 1. Introduction ....................5 1.1 Checklist ..................... 5 1.2 Product Description ................5 1.3 Features ..................... 6 1.4 Specifications ..................7 2. Hardware Description .................. 9 2.1 Front Panel ..................9 2.1.1 LED Indicators ................10 2.2 Rear Panel ..................11 3. -
Page 5: Introduction
1. Introduction 1.1 Checklist Check the contents of your package for the following parts: FSD-804P x 1 User’s Manual x 1 Two Rack-mounting Brackets with Power Cord x 1 Rubber Feet x 4 Attachment Screws x 1 If any of these pieces are missing or damaged, please contact your dealer immediately;... -
Page 6: Features
1.3 Features Physical Port z 8-port 10/100BASE-TX Fast Ethernet RJ45 copper z 4-port IEEE 802.3at/af PoE Injector (Port-1 to Port-4) Power over Ethernet z Complies with IEEE 802.3af/at Power over Ethernet end-span PSE z Up to 4 ports of IEEE 802.3af/802.3at devices powered z Supports PoE Power up to 30.8 watts for each PoE port z Each port supports 53V DC power to PoE powered device z 60-watt PoE budget... -
Page 7: Specifications
1.4 Specifications Model FSD-804P Hardware Specifications Hardware Version 10/100BASE-TX MDI/MDIX Ports 4 ports with 802.3at/af PoE injector function PoE Injector Port with Port-1 to Port-4 Switch Architecture Store-and-Forward Switch Fabric 1.6Gbps/non-blocking Switch Throughput@64 bytes 1.19Mpps@64 bytes 1K entries, automatic source address learning MAC Address Table and aging IEEE 802.3x pause frame for full-duplex... - Page 8 Power Pin Assignment 1/2(+), 3/6(-) PoE Power Budget 60 watts Max. Number of Class 2 PDs Max. Number of Class 3 PDs Max. Number of Class 4 PDs Standards Conformance Regulatory Compliance FCC Part 15 Class A, CE IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3x Flow control and back pressure Standards Compliance...
-
Page 9: Hardware Description
2. Hardware Description These switches provide two different running speeds – 10Mbps and 100Mbps, and automatically distinguish the speed of the incoming connection. This section describes the hardware features of the FSD-804P. For easier management and control of the FSD-804P, familiarize yourself with its display indicators and ports. -
Page 10: Led Indicators
Default PoE Mode PoE IP Camera FSD-804P Power 100 meters (328 feet) Extended PoE Mode PoE IP Camera FSD-804P Power 200 meters (656 feet) 10BASE-T UTP with PoE 100BASE-TX UTP with PoE Power Line (AC) 2.1.1 LED Indicators System Color Function Green Lights to indicate that the Switch has power. -
Page 11: Rear Panel
2.2 Rear Panel The rear panel of the FSD-804P has an AC inlet power socket, which accepts input power from 100 to 240V AC, 50-60Hz. 100-240V AC 50/60Hz, 2A Figure 2-2: FSD-804P Switch Rear Panel 1. The device is a power-required device which means it will not work till it is powered. -
Page 12: Hardware Installation
3. Hardware Installation Start up Please refer to the following for your cabling: 10/100BASE-TX All 10/100BASE-TX ports come with Auto-Negotiation capability. They automatically support 100BASE-TX and 10BASE-T networks. Users only need to plug a working network device into one of the 10/100BASE-TX ports, and then turn on the FSD- 804P. -
Page 13: Desktop Installation
3.1 Desktop Installation To install the FSD-804P on desktop, simply follow the following steps: Step 1: Attach the rubber feet to the recessed areas on the bottom of the FSD- 804P, as shown in Figure 3-1. 8- Po rt 10 /1 00 M bp Et he rn et s w ith 4-... -
Page 14: Rack Mounting
3.2 Rack Mounting To install the FSD-804P in a 19-inch standard rack, follow the instructions described below. Step 1: Place your FSD-804P on a hard flat surface, with the front panel positioned towards your front side. Step 2: Attach a rack-mount bracket to each side of the FSD-804P with supplied screws attached to the package. -
Page 15: Wall Mounting Installation
Step 6: Proceed with Steps 4 and 5 of session 3.1 Desktop Installation to connect the network cabling and supply power to your Switch. 3.3 Wall Mounting Installation Step 1: Please find the wall that can mount the FSD-804P. Step 2: Install two screws on the wall. Step 3: Hang the FSD-804P on the screws from the wall. -
Page 16: Product Application
3.4 Product Application 3.4.1 Connecting end node or Switch 1. Place the FSD-804P on a smooth surface or fasten the mounting brackets purchased separately with the provided screws in a standard 19” rack. 2. Connect the power cord to the power inlet socket of the FSD-804P and the other end into the local power source outlet. -
Page 17: Department/Workgroup Poe+ Switch
Cable distance for Switch The cable distance between the FSD-804P and PC should not exceed 100 meter for UTP/STP cable. Make sure the wiring is correct Category 3/4/5 cable can be used in 10Mbps operation. To reliably operate your network at 100Mbps, you must use Note an Unshielded Twisted-Pair (UTP) Category 5/5e/6 cable, or better Data Grade cabling. -
Page 18: Power Over Ethernet Powered Device
3.5 Power over Ethernet Powered Device Voice over IP Phones Enterprise can install PoE VoIP Phone, ATA and other Ethernet/non-Ethernet end-devices in the central area where UPS is installed for uninterruptible power system 3~5 Watts and power control system. Wireless LAN Access Points Museums, airports, hotels, scenic places, campuses, factories, and warehouses can install access points 6~12 Watts... -
Page 19: Power Over Ethernet Overview
4. Power over Ethernet Overview What is PoE? PoE is an abbreviation of Power over Ethernet. The PoE technology means a system safely transmits both power and data on Ethernet UTP cable. The IEEE standard for PoE technology requires Category 5 cable or higher for high power PoE levels, but can operate with Cat3 cable for low power levels. - Page 20 Powered Device A powered device (PD) is a device powered by a PSE and thus consumes energy. Examples include wireless access points, IP phones, and IP cameras. Many PDs have an auxiliary power connector for an optional, external power supply. Depending on the PD design, some, none, or all power can be supplied from the auxiliary port, with the auxiliary port sometimes acting as backup power in case of PoE supplied power failure.
- Page 21 The data pairs are used. Since Ethernet pairs are transformers coupled at each end, it is possible to apply DC power to the center tap of the isolated transformer without upsetting the data transfer. In this mode of operation, the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity.
-
Page 22: Troubleshooting
5. Troubleshooting This chapter contains information to help you solve issues. If the FSD-804P is not functioning properly, make sure the FSD-804P was set up according to instructions in this manual. The Link LED is not lit. Solution: Check the cable connection and also try to swap one new cable. 100BASE-TX port link LED is lit, but the traffic is irregular. -
Page 23: Appendix A Networking Connection
Appendix A Networking Connection A.1 10/100Mbps, 10/100BASE-TX When connecting Switch to another Fast Ethernet switch, a straight-through or crossover cable might be necessary. Each port of the Switch supports auto-MDI/ MDI-X detection, meaning you can directly connect the Switch to any Ethernet devices without making a crossover cable. -
Page 24: Cable Connection
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight-through cable and crossover cable connection: Straight Cable SIDE 1 SIDE 2 SIDE 1 1 2 3 4 5 6 7 8 1 = White/Orange 1 = White/Orange 2 = Orange...