Toshiba TRST-A10 SERIES Product Description
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Printer
  5. TRST-A10 SERIES
  6. Product description
Toshiba TRST-A10 SERIES Product Description

Toshiba TRST-A10 SERIES Product Description

Remote receipt printer
Hide thumbs Also See for TRST-A10 SERIES:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual, Maintenance Manual
TOSHIBA REMOTE RECEIPT PRINTER
TRST-A10 SERIES
Product Description
Original
Nov., 2007
(Revised
Feb., 2008)
Document No. EO10-13009A
PRINTED IN JAPAN

Advertisement

Table of Contents
loading

Related Manuals for Toshiba TRST-A10 SERIES

Summary of Contents for Toshiba TRST-A10 SERIES

  • Page 1 TOSHIBA REMOTE RECEIPT PRINTER TRST-A10 SERIES Product Description Document No. EO10-13009A Original Nov., 2007 (Revised Feb., 2008) PRINTED IN JAPAN...

  • Page 2: Table Of Contents

    EFFECTIVE PRINTING AREA ------------------------------------------------------------------------ 2- 1 DESIGN OF PAPER ROLL ----------------------------------------------------------------------------- 2- 3 CAUTION! 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC. 2. The contents of this manual may be changed without notification.

  • Page 3: Outline

    1. OUTLINE EO10-13009A 1.1 FEATURES OF THE PRINTER OUTLINE FEATURES OF THE PRINTER This printer is a single station printer for 80 mm width receipt and is equipped with the RS-232C serial interface, USB interface or parallel interface (option), conforming to the ESC/POS commands.

  • Page 4: Description Of Model Number

    S: Standard Interface (Serial & USB) P: Parallel Interface Printer Type 5: Dual Side Printer 0: Single Side Printer NOTE: Some combinations of the above specifications are not developed as products. For details, please refer to your nearest authorized TOSHIBA TEC representative.

  • Page 5: Overview And Dimensions

    [DC24V] (Socket connector) The built-in AC adapter supplies +24V power to the printer through this connector. Do not connect anything other than the Toshiba TEC Specified AC adapter. [Serial interface connector] An interface cable which connects the printer to a POS terminal or Personal Computer is...

  • Page 6: Led And Feed Button

    4 [Drawer interface Connector] [CDKO] (6 pin modular connector) A drawer cable which connects the printer to a drawer is connected to this connector. To this connector, a Toshiba drawer can be connected. Do not connect anything other than the connectable drawer.
  • Page 7 Tear off any excess paper against the tear-off blade. NOTE: If other LED status except for the above occurs, turn the power off, and then on. If this does not restore the LEDs, contact your nearest TOSHIBA TEC representative for assistance.

  • Page 8: Datascope Mode

    1. OUTLINE EO10-13009A 1.3 OVERVIEW AND DIMENSIONS 1.3.4 Datascope Mode Datascope Mode allows the user to test the printer’s communications. When in Datascope Mode the printer receives all communications, but instead of executing the commands it prints them out on receipt paper as hexadecimal numbers in the order received. For example, the ASCII character “A”...

  • Page 9: System Configuration

    1. OUTLINE EO10-13009A 1.4 SYSTEM CONFIGURATION SYSTEM CONFIGURATION DC 24V AC Adapter Serial or Parallel Interface POS Terminal (ST-A10 series, etc.) Drawer Interface (Drawer Kick Specification) TOSHIBA TEC DRAWER (DRWST-51A-8MVG-QM-R,etc.)

  • Page 10: Basic Specification

    1. OUTLINE EO10-13009A (Revision Date: Feb. 06, 2008) 1.5 BASIC SPECIFICATIONS BASIC SPECIFICATIONS Item Description Printing method Line thermal dot printing method Printing width (Font Size 1) (Font Size 2) 80 mm (576 dots) 80 mm (560 dots) 58 mm (432 dots) 58 mm (424 dots) Resolution 203.2 dpi x 203.2dpi...

  • Page 11: Electronic Specifications

    1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS ELECTRONIC SPECIFICATIONS 1.6.1 CPU ....... UP0703111A 1.6.2 Serial Interface (RS232) 1. Specification (1) Synchronization method: Asynchronous (2) Baud rate: 9600, 19200, 38400,57600,115200 BPS (selectable) (3) Transmission parameter: Start bit: 1 bit Word length: 7 bit or 8 bit (selectable) Parity: None, even, odd (selectable) Stop bit: 1,2 bits selectable (4) Signal level:...
  • Page 12 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS RS232 9 Pin to 9 Pin Cable 9 Pin Female 9 Pin Female 5 LGND LGND 5 9 SHLD SHLD Applicable connector: D-sub connector Printer side: 1002-09MS4G-L (CHUFON or equivalent) Cable side: DB9 RS232 F/F serial cable NOTE: The RS-232C signal is according to EIA RS-232C.
  • Page 13 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS When the DTR/DSR control is selected, the printer confirms this signal is SPACE and then sends the status data. When it is not selected, the data is sent without DSR. Signal ground. Clear to send. This is asserted by host terminal to acknowledge RTS and allow printer to transmit.
  • Page 14 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 4. Error detection If a parity error, framing error, and overrun error is detected, the data is stored into the buffer as “? Framing error: This error occurs when no stop bit is found in the frame. The data is stored into the buffer as “?”.
  • Page 15 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS Electric specification For RS232, SP3243E or equivalent Input signal (RxD, DSR, CTS) [ Printer side ] [ Host side ] DTR (RxIN) DSR, DCD (RxOUT) 5Kohm TxD (RxIN) RxD (RxOUT) 5Kohm (RxIN) CTS (RxOUT) 5Kohm Where x denotes 1, 2 or 3 Output signal (DTR, TxD, RTS)
  • Page 16 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1.6.3 USB Interface Specification Version 2.0 full speed. Connector description Signal Description +3.3Vdc Data – (Differential pinout) Data +(Differential pinout) Signal Ground I/O signal USB is a serial bus. It uses 4 shielded wires: two for power (+3.3V & GND) and two for differential data signals (labelled as D+ and D- in pinout).
  • Page 17 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS -Interrupt Transfers are used when moderate amounts of data have to transfer within a specific amount of time. -The ML60851E requests interrupts to the local MCU, etc., by asserting the -INTR pin. -Transfer of handshake packet in a direction opposite to that of the data packet. When packet transfer is completed normally, an ACK packet is returned and the operation proceeds to the next packet transfer.
  • Page 18 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS Normally condition 3 will not occur so we will look at cases 1 and 2. If 64 byte packets are continually sent back to the host, then it will continue to read the data to match the block size requested before it sends the block back to the driver.
  • Page 19 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1.6.4 Parallel Interface (i) Compatibility Mode (Host to  P rinter: Conforming to Centronics interface) (1) Data input method: 8-bit parallel (2) Synchronization method: nStrobe signal externally supplied (3) Hand shake: nAck signal and Busy signal (4) Signal level: All signals are TTL compatible.
  • Page 20 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS (iii) Connector Description Source Compatibility mode Nibble Mode Host Nstrobe HostCLK Host/Ptr Data0(LSB) Data0(LSB) Host/Ptr Data1 Data1 Host/Ptr Data2 Data2 Host/Ptr Data3 Data3 Host/Ptr Data4 Data4 Host/Ptr Data5 Data5 Host/Ptr Data6 Data6 Host/Ptr Data7 Data7 Printer Nack...
  • Page 21 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS (iv) Input/Output signal (1) Input signal to the printer • DATA: 8-bit parallel signal (positive logic) • STB: Strobe signal to capture 8-bit data (negative logic) • RESET: A signal to reset the printer (negative logic) •...
  • Page 22 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS (3) Condition of input/output The input signal DATA1Ω8 are pulled up by 10KΩ, and other input signals are by 10KΩ, respectively. [ Printer side ] [ Host side] The output signal DATA1Ω8 are pulled up by 10KΩ, and other output signals are by 2.2KΩ,respectively.

  • Page 23: Drawer Interface

    4) The output current should not exceed 1.5A, which may cause the printer to be broken, burned. 5) Connect the solenoid only. A telephone line cannot connect to this drawer connector. 6) The drawer of which interface is TOSHIBA TEC standard (4-pin modular type connector) cannot be connected. 1-21...

  • Page 24: Drive Circuit

    1. OUTLINE EO10-13009A (Revision Date: Jan. 18, 2008) 1.7 DRAWER INTERFACE 1.7.4 Drive Circuit 1-22...

  • Page 25: Dc Power Connector

    1. OUTLINE EO10-13009A 1.8 DC POWER CONNECTOR DC POWER CONNECTOR The DC power connector of the AC adapter is shown below. Connector Description Function +24V SHELL Applicable connector: TCS7960-53-2010 (HOSHIDEN) or equivalent. Adaptable connector: TCP8927-63-1100 (HOSHIDEN) or equivalent. TCP8927-53-1100 (HOSHIDEN) or equivalent. GA1009-38TINI (WIESON) or equivalent.

  • Page 26: Sensors

    1. OUTLINE EO10-13009A 1.10 SENSORS 1.10 SENSORS Thermal Head Cutter Cover Open Sensor Paper Roll Platen P.E. Sensor Cutter Home Sensor Paper Low Sensor 1) Cover open sensor This sensor performs synchronizing with the printer cover’s open/close at the paper roll replacement, and adopts a mechanical switch.

  • Page 27: Supply Specifications

    2. SUPPLY SPECIFICATIONS EO10-13009A 2.1 EFFECTIVE PRINTING AREA SUPPLY SPECIFICATIONS EFFECTIVE PRINTING AREA 80mm paper Front Page Rear Page A = 4 mm +/-1 mm B = 4 mm +/-1 mm C = 17.5mm +/-1 mm Printable Area E = 72mm F = Depend on print data condition A=4mm+/- 1mm Printable Area...
  • Page 28 2. SUPPLY SPECIFICATIONS EO10-13009A 2.1 EFFECTIVE PRINTING AREA 58mm paper Front Page Rear Page A = 2 mm +/-1 mm B = 2 mm +/-1 mm C = 17.5mm +/-1 mm E = 54mm Printable Area F = Depend on print data condition A=4mm+/- 1mm Printable Area B=4mm+/- 1mm...

  • Page 29: Design Of Paper Roll

    12.5 +/- 0.5 mm Recommended thermal paper Only paper rolled onto a core is acceptable, however, the paper end should not be pasted to the core. TOSHIBA TEC recommends using the following thermal paper for this product. Manufacturer : NIPPON PAPER...

Table of Contents