Advertisement
The SMV 3000 Smart Multivariable
Flow Transmitter is available with
a variety of options, including:
Mounting Bracket - MB, SB, FB
Available in angle or flat style
suitable either for horizontal or
vertical mounting on a two-inch
pipe or for wall mounting.
Indicating Meter - ME
An analog meter is available with 0
to 10 square root or 0 to 100%
linear scale.
Adapter Flanges - S2, T2, V2
Convert standard 1/4 inch NPT
connections to 1/2 inch NPT.
Available in Stainless Steel,
Hastelloy C and Monel.
Conduit Adapters - A1, A2
Converts standard 1/2 inch NPT
Electrical Conduit Entry to M20 or
3/4 inch NPT. Adapters are 316
SS.
Head Gaskets - VT
Replaces standard PTFE head
gaskets with Viton.
Write Protection - WP
A jumper on the SMV 3000's main
board is activated so that the
configuration database in read-
only and can not be changed.
Customer Tag - TG
This stainless steel tag connected
to the SMV 3000 via wire allows
you to specify information - 4 lines
with 28 characters per line
maximum.
Clean Transmitter - OX
Insures that the SMV 3000 has
been cleaned of hydrocarbons so
that it can be used in applications
such as oxygen and chlorine
service.
SMV 3000 Options
Over-Pressure Leak Test - TP
Certificate confirming that the SMV
3000 has been leak tested to 4500
psi.
Additional Warranty - W1 - W4
Standard warranty for the SMV
3000 is 1 year after delivery. The
extended warranty options allow
the SMV 3000 to be warranted for
up an additional 4 years.
Laminar Flow Element - LF
Provides a SMV 3000 transmitter
with specific mass flow equations
supporting the Meriam Laminar
Flow Element for applications such
as combustion air.
Lightning Protection - LP
A terminal block with circuitry that
protects the transmitter from
transient surges induced by
nearby lightning strikes. This does
not provide protection for RTD or
thermocouple wiring.
Side Vent/Drain - SV
Replaces standard End Vent/Drain
plugs with side vent/drain plugs.
Custom Calibration - CC
Standard calibration for SMV 3000
includes: 0 - 100 inches
DP, 0 - 125 psia for AP and -328 to
852 degrees. F. for a Pt. 100 Ohm
RTD input. Custom calibration
allows you to have the factory
calibrate the SMV 3000 based on
your application. The CC - Custom
Calibration form must be
completed at time of order.
Multivariable Tx. Configuration -
MC
Allows you to have the SMV 3000
configured at the factory based on
your application. Includes range
configuration for DP, AP, Temp.
and Compensated Flowrate. The
MC form must be completed at
time of order.
NACE Nuts and Bolts - CR
Standard head nuts and bolts for
the SMV 3000 are carbon steel.
CR option supplies A286SS bolts
and 302/304SS nuts for
environments that are corrosive to
carbon steel. 316SS bolts for
adapters supplied also.
SS Center Vent/Drain and
Bushing - CV
Allows a special bushing on side
and end vent-drain plugs.
Blind DIN SS Flanges - B2
The blind flange option removes
all side or end vents/drains from
the process flanges. Used when
customer will vent or drain from
manifold.
Calibration Test Report - F1
Provides document stating
calibration points for all measured
variables.
Certificate of Conformance - F3
Provides document stating that the
SMV 3000 conforms to all
Honeywell quality practices.
Certificate of Origin - F5
Provides document stating that all
for
parts originated here.
H 2 O
Modified DIN Process Heads -
DN
Replaces standard heads with
modified heads.
NACE Certificate - F7
Provides document stating that
specified wetted parts conform to
NACE specifications.
34-SM-03-01
Page 19
Advertisement
