Page 1
Model No. PFEL29240 Serial No. Serial Number Decal QUESTIONS? If you have questions, or if there are missing parts, we will guar- antee complete satisfaction through direct assistance from our factory. TO AVOID DELAYS, PLEASE CALL DIRECT TO OUR TOLL- FREE CUSTOMER HOT LINE.
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precau- tions before using the elliptical crosstrainer. 1. Read all instructions in this manual before using the elliptical crosstrainer. 2. It is the responsibility of the owner to ensure that all users of the elliptical crosstrainer are adequately informed of all precautions.
The model number is PFEL29240. The serial number is found on a decal attached to the elliptical crosstrainer (see the front cover of this manual for the location of the decal).
ASSEMBLY Assembly requires two persons. Place all parts of the elliptical crosstrainer in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the included allen wrenches, assembly requires a phillips screwdriver , an adjustable wrench , and a rubber mallet...
Page 6
1. Identify the Front Stabilizer (10), which has round Endcaps (21) on its ends. While another person lifts the front of the Frame (1), attach the Front Stabilizer to the Frame with two M10 x 75mm Carriage Bolts (34) and two M10 Nylon Locknuts (33). 2.
Page 7
tion shown, connect the Extension Wire (68) to the Reed Switch Wire (53). Next, connect the Resistance Cable (42) to the Lower Resistance Cable (43) in the following way: • See drawing A. Pull up on the metal bracket, and insert the tip of the Resistance Cable (42) into the wire clip on the Lower Resistance Cable (43) as shown.
Page 8
7. Identify the Left Pedal Leg (11), which is marked with a sticker. Attach the Left Pedal (13) to the Left Pedal Leg with two M8 x 52mm Button Screws (27), two M8 Split Washers (28), and two M8 Washers (71). Attach the Right Pedal (not shown) in the same way.
HOW TO ADJUST THE RESISTANCE OF THE PEDALS As you exercise, you can adjust the resistance of the pedals with the resistance knob on the upright. To increase the resistance, Knob turn the knob clockwise; to decrease the resistance, turn the knob counter- clockwise.
Page 10
HOW TO USE THE CONSOLE Turn on the console. Note: The console requires four 1.5V “D” batteries (see assembly step 3 on page 6). To turn on the console, press the On/Reset button or begin pedaling. (See the drawing above to identify the On/Reset button.) Follow your progress with the display.
Page 11
If there are thin sheets of plastic on the Metal metal contacts Contacts on the hand- grips, peel off the plastic. To use the hand- grip pulse sen- sor, hold the handgrips with your palms resting against the metal contacts. Avoid moving your hands.
Inspect and tighten all parts of the elliptical crosstrainer regularly. Replace any worn parts immediately. To clean the elliptical crosstrainer, use a damp cloth and a small amount of mild dish soap. Important: Keep liquids away from the console and keep the console out of direct sunlight.
WARNING: • Before beginning this or any exercise pro- gram, consult your physician. This is espe- cially important for persons over the age of 35 or persons with pre-existing health prob- lems. • The pulse sensor is not a medical device. Various factors, including the user's move- ment, may affect the accuracy of heart rate readings.
Key No. Qty. Description Frame Upright Left Side Shield Right Side Shield Handlebar Leg Left Handlebar M10 x 74mm Button Bolt Right Handlebar Rear Stabilizer Front Stabilizer Left Pedal Leg Right Pedal Leg Left Pedal Right Pedal Pedal Disc Disc Crossbar Flywheel Side Shield Bracket Drive Belt...
• The MODEL NUMBER of the product (PFEL29240) • The NAME of the product (PROFORM 675 CARDIO CROSSTRAINER) • The SERIAL NUMBER of the product (see the front cover of this manual) •...