Selecting Patches For Playing (Play Mode); Panel Display; Selecting A Patch; Adjusting The Sound - Zoom Guitar Effects Console G9.2tt2q Operation Manual

Selecting Patches for Playing
Immediately after you turn on the G9.2tt, it is always in the mode for selecting and using patches (play
mode). The most recently used patch is automatically called up again. The various operation steps in play
mode are described in this section.

Panel display

Group name (U, u, A, b)
Shows the number of the
Groups A and b are read-only
parameter knob that adjusts
groups (preset groups). Groups U
the patch output level.
and u are read/write enabled
groups (user groups).
Patch name
A0 A0
AmpDrive ™LVL100 AmpDrive
ɡ ɡCh.AB Ch.AB ə əBpmTp
Bank number (0 – 9)
Function foot switch 1/2 assignment
Shows the function assigned to the function foot switch 1/2 (→ p. 38).
[CHANNEL A/B] keys The key for the channel (A or B) that is currently
Effect module
keys
Foot switch
1 – 5 LEDs

Selecting a patch

This section explains how to select a patch in play
mode.
1.
Press a foot switch 1 – 5 whose LED
is not lit.
14
(Play Mode)
In play mode, the following information is shown
on the panel.
Patch level
Shows the output level setting
(2 – 100) for the currently
selected patch
"E" symbol
LVL100
If the currently displayed setting
BpmTpé
value differs from the original
patch setting, the indication "E"
(for "Edited") appears.
selected for the pre-amp section is lit.
Keys for modules that are active in the
currently selected patch are lit in red.
The LED of the foot switch for the currently
selected patch is lit.
The LED of the pressed switch lights up,
indicating that a new patch has been called up.
ZOOM G9.2tt
HINT
• In play mode, you can select a patch by turning
parameter knob 1.
• When you press a foot switch whose LED is lit,
the same patch is called up once more.
2.
To switch to a patch in another bank,
use the BANK [W]/[Q] foot switches
to change the bank and then use foot
switches 1 – 5 to select the patch.
BANK [W]/[Q] Foot switches
foot switches 1 – 5
When you repeatedly press the BANK [Q] foot
switch, the G9.2tt switches the group/bank as
follows.
User groups
Preset groups
A 0 A 1 A 9 B 0 B 9
HINT
In play mode, you can switch the group/bank by
turning the [TYPE] knob.
NOTE
• When using the BANK [W]/[Q] foot switches to
change banks, press and release the switch
quickly.
• If you keep the BANK [W] foot switch depressed
for more than one second, the G9.2tt switches
to manual mode (→ p. 19).
• If you keep the BANK [Q] foot switch depressed
for more than one second, the G9.2tt switches
to the bypass condition (effects off). If you keep
the switch depressed further, the G9.2tt
switches to the mute condition (original sound
and effect sound both off) (→ p. 21).
ZOOM G9.2tt

Selecting Patches for Playing (Play Mode)

Adjusting the sound

In play mode, you can use the knobs on the panel
to adjust the basic parameters of the pre-amp
section (distortion type and intensity, EQ boost/
cut etc.).
1.
In play mode, select the patch.
2.
Press one of the [CHANNEL A/B] keys
to select the pre-amp channel A or B
for which to make the adjustment.
The pre-amp section of the G9.2tt has two
separate channels which allow individual settings.
Simply pressing one of the [CHANNEL A/B]
keys instantly switches the channel.
HINT
You can switch between channel A and B with the
FUNCTION foot switch 1/2 (→ p.38).
3.
To change the distortion type, turn
the [AMP TYPE] knob.
The [AMP TYPE] knob selects the distortion type
( t h e a m p o r c o m p a c t e f f e c t t h a t i s b e i n g
simulated). When you turn the knob, the name of
the new amp type appears on the display.
PRE-AMP PRE-AMP œ–ø––– œ–ø–––
FD Clean é–œ–œµµ FD Clean é–œ–œµµ
[AMP TYPE]
Type name "E" symbol
knob
HINT
• When you have changed the distortion type, the
"E" symbol appears on the display, and the
[STORE/SWAP] key lights up.
• If the currently displayed setting value differs
from the original patch setting, the indication "E"
(for "Edited") appears.
15