Adjusting The Expression Pedal Torque - Zoom Guitar Effects Console G9.2tt2q Operation Manual

[Table 2]
The table below shows an example for Z-pedal operation when vertical direction is assigned to "PdlPosi V"
and horizontal direction to "PdlPosi H".
Horizontal
Vertical
Color direction
min
direction
max 1000 cent +1 octave
1
min -200 cent 0 cent
max +1 octave 1500 cent
2
min 0 cent 300 cent
max 300 cent +1 octave
3
min 0 cent 0 cent
max 500 cent +1 octave
4
min 0 cent 0 cent
Z-Talking
This effect changes the guitar sound into a talking sound. When using the Z-pedal, vowels can be changed in various
ways by moving the pedal in the vertical or the horizontal direction.
Try assigning the vertical direction of the Z-pedal (P2V1 - P2V4) to the "Formant V" parameter and the horizontal
direction (P2H1 - P2H4) to the "Formant H" parameter.
PARM1 PARM2
Variation Tone
1 ñ 5 0 ñ 10
Selects the sound variation
type caused by the pedal (see Adjusts the tone.
Table 3).
[Table 3]
The table below shows an example for Z-pedal operation when vertical direction is assigned to "Formant V"
and horizontal direction to "Formant H".
Horizontal
Vertical
direction
Variation
min
direction
max i
1
min a
max u
2
min i
max e
3
min u
REVERB module
Z-Delay
This is a delay effect which allows adjustment of panning and mix level using the pedal.
Try assigning the vertical direction of the Z-pedal (P2V1 - P2V4) to the "Mix" parameter and the horizontal direction
(P2H1 - P2H4) to the "Pan" parameter.
PARM1 PARM2
1 ñ
Time FeedBack
0 ñ 100
3000
Adjusts the delay time. Adjusts the amount of feedback.
Z-Dimension
This is a spatial effect which allows adjustment of depth, panning, and reverberation using the pedal.
Try assigning the vertical direction of the Z-pedal (P2V1 - P2V4) to the "Depth" parameter and the horizontal direction
(P2H1 - P2H4) to the "Pan" parameter.
PARM1 PARM2
Pan Depth
L50 ñ R50 0 ñ 100
Adjusts the left/right panning Adjusts the sound position
of the sound. depth.
Z-Tornado
This is a delay effect which causes the effect sound to swirl like a tornado.
Try assigning the vertical direction of the Z-pedal (P2V1 - P2V4) to the "Rate" parameter and the horizontal direction
(P2H1 - P2H4) to the "Width" parameter.
PARM1 PARM2
1 ñ
Time
Rate
1 ñ 50
3000
Adjusts the delay time. Adjusts the modulation rate.
Horizontal
Vertical
Color
direction
max direction min max
max 700 cent +1 octave
5
min 0 cent 0 cent
max +1 octave +2 octave
6
min 0 cent 0 cent
max +1 octave (0 Hz)
-
7
min 0 cent 0 cent
max 500 cent -1 octave
8
min -700 cent +1 octave
PARM3 PARM4
Formant V Formant H
0 ñ 100
Adjusts the formant [peaks in Adjusts the formant [peaks in
the acoustic frequency the acoustic frequency
spectrum that characterize spectrum that characterize
vowels] (vertical direction of vowels] (horizontal direction
pedal). of pedal).
Horizontal
Vertical
Variation direction
max min max
direction
u max o a
4
e min e i
e max a i
5
o min o u
o
a
PARM3 PARM4
Pan Mix
L50 ñ R50
Adjusts the level of the effect
Adjusts the delay sound left/
sound mixed to the original
right panning.
sound.
PARM3 PARM4
Decay Mix
1 ñ 30
Adjusts the mixing level of the
Adjusts the reverb duration.
reverb sound.
PARM3 PARM4
Width Mix
L50 ñ R50
Adjusts the sound movement Adjusts the mixing level of the
range. delay sound.

Adjusting the Expression Pedal Torque

A djus ting hor iz onta l tor que for e xpre s s ion pe da l 2
1
Fully raise the expression pedal 2
at the right side of the unit.
2
Insert a 3mm size hex wrench into the fitting
on the outside of the panel. To increase
0 ñ 100
pedal firmness, turn the wrench clockwise.
To decrease pedal firmness, turn the wrench
counterclockwise.
A djus ting ve r tic a l torque for e xpre s s ion pe da l 1 /2
1
Turn power to the G9.2tt off,
disconnect the AC adapter
from the unit, and turn the
unit upside down.
0 ñ 100
2
Insert a 3 mm size hex wrench into the hole on
the underside of the left or right expression
pedal. To increase pedal firmness, turn the
wrench clockwise. To decrease pedal firmness,
turn the wrench counterclockwise.
Expression pedal 2 of the G9.2tt is designed for operation with one foot. When the pedal is
0 ñ 100 fully turned to the right, pushing it strongly down, hitting it, or otherwise exerting strong force
Warning on it will damage the pedal. Be sure to operate the pedal only within its designated range.
If you loosen the pedal too much, the internal screw may come off, and you will no longer be
able to tighten the pedal. Perform this operation with care.
If the screw should have come off inside the unit, contact your dealer or an authorized Zoom
service station.
Never try to open the cabinet of the G9.2tt yourself, and never turn power to the G9.2tt on if
the screw is unsecured inside the unit. Otherwise the electronic circuitry may be seriously
damaged.
0 ñ 100
© ZOOM Corporation
Reproduction of this document, in whole or in part, by any means, is prohibited.
3
Pedal adjustment fitting is visible
on rear of expression pedal 2.
Tighten
Loosen
3 mm size hex wrench
40 mm or longer
G9.2tt bottom view
Tighten
Loosen
G9.2tt-Pedal Adjust-E-1
4