Difference And Compatibility Of L300P Series And Sj700B Series - Hitachi SJ700 series Manual

DIFFERENCE and COMPATIBILITY
of L300P series and SJ700B series
Items
Copying the parameter settings
Parameter display mode.
Retry or trip parameter
d001:Output frequency monitoring
d007:Scaled output frequency monitoring
A001:
Frequency source setting
A016:
External frequency filter time const.
A038:Jog frequency setting
Change function
A105:
[OI]-[L] input start frequency enable
b012, b212, b312:
Electronic thermal function
b013, b213, b313:
Electronic thermal characteristic
b092:Cooling fan control
b095:Dynamic braking control
Removable
Intelligent input terminals
Control
circuit
Intelligent output terminals
Position
Terminal
Screw diameter
Main
circuit
Position
Others
Easy-removable Dc bus Capacitor
Dynamic Brake circuit
110L
150L
Minimum value of
110H
150H
Installation
Dimensions
External radiating fin
Digital operator position
Keypad potentiometer on digital operator
SJ-DG
SJ-DN / SJ-DN2
Option boards
SJ-PB/PBT, SJ-PB2/PBT2
SJ-LW
Option position
Note1: Since a response falls the V/F characteristic curve selection SLV should make this setup small.
Note2: 450, 550L/H and 750H:Metal fittings differ.
L300P
You can copy the parameter settings from the L300P series into the SJ700B series.
(You cannot copy the parameter settings from the SJ700B series to the L300P series because the SJ700B
series has many new functions and additional parameters.)
No display mode selection.
(full display)
Instantaneous power failure/under-voltage/
overvoltage/overcurrent:It sets up by b001.
You can not change the output frequency setting
by using the up and or down key.
Default:00
(Keypad potentiometer on digital operator)
Default:8
Setting range:0 to 999Hz
Default:01 (external start frequency)
Setting upper limit:120%
Default:00 (reduced-torque characteristic)
Default:00 (always operating the fan)
Default:00 (disabling)
Removable
5 terminals
2 terminals (Relay)
370L/H:97mm upper part from L300P.
Other model:same position.
150L/H M6 (Ground Screw)
M8 (Ground Screw)
370L
550L M10
M6
450H
110,150LF/HF:10mm upper part from L300P. 185 to 220L/300H:29mm upper part from L300P.
300L:18mm upper part from L300P. 370L:77mm upper part from L300P.
370H:72mm upper part from L300P. 750L:25mm upper part from L300P.
Other model:same position.
185 to 300L/H:RB there is not a terminal.
All the models are possible.
Up to 15kW
All models are the same enclosure size.
Those with compatibility. Note 2
300L/H:97mm upper part from L300P.
Other model:same position.
Those with compatibility.
Those with compatibility.
Note:Since the SJ700B series has many new functions and additional parameters,some functions of the
SJ-DN, and SJ-PB/PBT (option boards conforming to the open network specifications)cannot be
implemented on the SJ700B series.
available
370L/H:97mm upper part from L300P.
Other model:same position.
series
Basic display mode/Data comparison function addition.
Note:basic display mode [factory setting] To display all
parameters,
specify "00" for "b037".
Instantaneous power failure/under-voltage:It sets
up by b001.
overvoltage/overcurrent:It sets up by b008.
You can not change the output frequency setting
by using the up and or down key.
Default:02
(Digital operator)
Default:31 Note 1
Setting range:
0.01 to 999Hz (0Hz setup is impossible)
Default:00 (0Hz)
Setting upper limit:100%
Default:01 (constant-torque characteristic)
Default:01 (operating the fan only during inverter
operation
[including 5 minutes after power-on and power-off])
Default:01 (enabling [disabling while the motor is
topped])
Removable
(You can mount the L300P into the SJ700B .)
8 terminals
5 terminals (Open collector)
M5 (Ground Screw)
M6 (Ground Screw)
M8
M8
185 to 300H:RB there is a terminal.
18.5kW or more is possible.
Up to 30kW
17
17
50
50
Yes.
not available
SJ700B
series
10
10
35
35
No. (Option)
36