Emerson MP25A4 User Manual page 149

Safety Product Mechanical
Information information Installation
12.1.4 Power dissipation
The table below shows the maximum drive losses, assuming high output
current ripple content.
Table 12-4 Drive losses
Loss @
Model
MP25A4(R)
MP25A5(R)
MP45A4(R)
MP45A5(R)
MP75A4(R)
MP75A5(R)
MP105A4(R)
MP105A5(R)
MP155A4(R)
MP155A5(R)
MP210A4(R)
MP210A5(R)
MP350A4(R)
MP350A5(R)
MP350A6(R)
MP420A4(R)
MP470A5(R)
MP470A6(R)
MP550A4(R)
MP700A4(R)
MP825A4(R)
MP700A5(R)
MP700A6(R)
MP825A4(R)
MP825A5(R)
MP825A6(R)
MP900A4(R)
MP1200A4(R)
MP1200A5(R)
MP1200A6(R)
MP1850A4(R)
MP1850A5(R)
MP1850A6(R)
12.1.5 AC Supply requirements
The standard drive is rated for a nominal supply voltage up to 480Vrms.
An optional rating of 575Vrms is available for size 1 drives.
An optional rating of 575Vrms and 690Vrms is available for size 2 drives.
Grounded delta supplies exceeding 575V are not permitted
for drives up to and including 210A. Grounded delta supplies
exceeding 600V are not permitted for drives rated 350A and
above.
WARNING
12.1.6 Supply types
Drives rated for supply voltages of up to 575V (rated up to 210A) and
600V (350A and above), are suitable for use with any supply type i.e.
TN-S, TN-C-S, TT, IT with grounding at any potential i.e neutral, centre
or corner ("Grounded delta").
Grounded delta supplies >575V are not permitted for drives rated up to
and including 210A. Grounded delta supplies >600V are not permitted
for drives rated 350A and above.
Mentor MP User Guide
Issue: 3
Electrical Getting Basic
installation started parameters
Loss @ Loss @
40°C 50°C 55°C
W W
125
168 139
219 194
274
400
561 456
954
1045
1154
1546 1268 1162
1568 1354
1663
1955 1795
2160 1909 1751
2381 2004 1795
2220 1908 1751
3635 3660
5203 4418 4139
www.controltechniques.com
Running the SMARTCARD
Optimization
motor operation
12.1.7 Main AC supply
Table 12-5 Three phase AC supply
Specification
Maximum nominal supply
Tolerance
W
Minimum nominal supply
91
Tolerance
12.1.8 Auxiliary AC supply
117
Table 12-6 Line to line supply
183
Maximum nominal supply
Tolerance
Minimum nominal supply
Tolerance
310
12.1.9 Line reactors
The Mentor MP, in common with all naturally commutated thyristor
drives, causes voltage notches at the input supply terminals. In order to
avoid disturbance to other equipment using the same supply, the
addition of external line inductance is strongly recommended in order to
restrict the depth of the notches imposed on the shared supply. This is
generally not necessary where a dedicated transformer is used to supply
the drive.
The following recommendations for added line inductance, have been
calculated based on the power drive systems standard: EN 61800-
3:2004 "Adjustable speed electrical power drive systems – Part 3: EMC
requirements and specific test methods".
Table 12-7 Minimum required line inductance for a typical
application (50% ripple content)
Drive
rated
400V
current
μH
A
25 220
45 220
75 220
105 220
155 160
210 120
350 71
420 59
470
550 45
700 36
825
900 28
1200 21
1850 18
NOTE
1. The above assumes the supply has 1.5% impedance.
2. Assumes a minimum supply rating of 5kA and a maximum rating of
60kA.
12.1.10 Temperature, humidity and cooling method
Ambient temperature operating range:
0°C to 55°C (32°F to 131°F).
Output current derating must be applied at ambient temperatures
>40°C (104°F).
Onboard Advanced Technical
PLC parameters data
Product voltage variant
480V 575V
480V 575V
+10%
24V
-20%
Specification
System voltage Typical
current
480V 575V 690V
μH μH μH
260 320
260 320
260 320
260 320
190 230
140 170
85 110 120
71
80 91
54
43 53 61
45 52
33
25 31 36
23 29 32
UL
Diagnostics
information
690V
690V
500V
-10%
Value
480V
+10%
208V
-10%
Maximum
current
rating rating
A A
21 22
38 40
63 67
88 94
130 139
176 188
293 313
351 375
393 420
460 492
586 626
690 738
753 805
1004 1073
1548 1654
149