Setting The Setup Menu; Channel Selection; Auto Channel Programming; To Add Or Erase Channels From Memory - Sanyo VWM-800 Instruction Manual

SETTING THE SETUP MENU

1
Press MENU and the MAIN menu will appear.
2
Press or to select the SETUP menu, then press
D D E E
ENTER. The SETUP menu will appear.
3
D D E E
Press or to choose a desired item on the SETUP
menu. Then press or
F F G G
FUNCTION OSD
The onscreen display of this VCR can be turned on or off.
• The FUNCTION OSD is switched between ON and OFF by
F F G G
pressing or .
LANGUAGE SELECT
The onscreen programming of this VCR can display in either
English, Spanish, or French.
• The LANGUAGE SELECT is switched among ENGLISH,
SPANISH and FRENCH by pressing
AUDIO MODE DISPLAY
The VCR has two separate audio playback systems, the high
quality VHS Hi-Fi system and standard NORMAL mono system.
The same audio is generally recorded on both systems. The
VHS Hi-Fi system plays on separate (left and right) channels,
and the NORMAL system plays monaural sound. The normal
track is always played so the cassette can be played on a VCR
that does not have VHS Hi-Fi.
• The AUDIO MODE is switched between HI-FI and NORMAL
F F G G
by pressing or .
BROADCAST TYPE DISPLAY (STEREO/SAP/MONO)
Multichannel Television Sound (MTS) carries stereo and/or
Second Audio Program (SAP) bilingual signals. Set this display
to the desired position when both MTS stereo and SAP signals
are received. When only one of the MTS signal is received, the
VCR automatically selects the corresponding receiving mode
(Stereo or SAP) regardless of the selected position.
For normal operation, the display should be in the STEREO posi-
tion. The VCR will then record a STEREO program when available,
and record a mono program IF the program NOT IN STEREO.
For weak STEREO and/or SAP broadcasting, changing the dis-
play to mono may give clearer sound.
• The BROADCAST TYPE is switched among STEREO, SAP,
F F
and MONO by pressing or
AUDIO OUTPUT DISPLAY (STEREO/LEFT/RIGHT)
Used during playback [when AUDIO MODE display (HI-FI/NOR-
MAL) is in HI-FI position] for selecting the audio output signals from
the AUDIO OUT terminals (L ch and R ch), and VHF/UHF/CATV.
This display setting should normally be left in the stereo position,
so that when a stereo tape is played, the stereo sound will be
heard through the left and right channels. If a mono tape is
played and the audio output is set to stereo, the same mono
sound will be heard from both left and right channels.
• The AUDIO OUTPUT is switched among STEREO, LEFT, and
F F G G
RIGHT by pressing or .
TV GUARDIAN SETUP
Details are on the 9 page.
to choose a desired setting.
F F G G
or .
G G
.

CHANNEL SELECTION

This VCR is equipped with a frequency synthesized tuner
capable of receiving up to 181 channels. These include
VHF channels 2-13, UHF channels 14-69 and CATV
channels 1-125.
PREPARATION
• Connect the VCR to the desired type of antenna or cable TV
system, as shown in ANTENNA TO VCR CONNECTIONS .

AUTO CHANNEL PROGRAMMING

1
Press MENU and the MAIN menu will appear.
2
D D E E
Press or to select the TUNING menu, then press
ENTER. The TUNING menu will appear.
3
E E
Press to choose the SOURCE SELECT item, then
press F F or G G to select TUNER.
F F G G
• Press or repeatedly to switch among TUNER, LINE1
and LINE2.
4
Press D D or E E to choose the AUTO CHANNEL SET
F F G G
item, then press or
• The tuner will automatically cycle through all available
channels in the area and place them in the tuner's memory.
5
After the AUTO CHANNEL SET PROCEEDING is com-
plete, make sure the TUNING BAND is set appropriate-
ly (TV or CATV) by pressing
correct TUNING BAND (TV or CATV) by pressing
G G
using the TUNING menu.
• Remember, TV is for the air antenna reception, CATV is for
cable or wireless cable connection.
6
Press MENU to return to the TV screen.
Use CH/TRACK ( / ) or CHANNEL ( / ) on the front
panel to cycle the VCR through the channels in memory.
TO ADD OR ERASE CHANNELS FROM
MEMORY
This feature allows you to add or
erase channels from memory manu-
ally.
1
Press E E to choose the CH.
ADD/DEL item on the TUNING
menu. Press F F or G G to select a
channel to add or erase.
2
Press ENTER to add or erase the channel.
Repeat steps 1 and 2 to add or erase channels.
3
Press MENU to return to the TV screen.
7
to set the channel.
D D or E E and choosing the
F F or