IDENTIFICATION OF SYMBOLS WARNING! This chain saw can be dangerous! Care- less or improper use can cause serious or even fatal injury. Always wear appropriate ear protection, eye protection and head protection. Always use two hands when operating the chain saw. WARNING! should be avoided;...
S Keep the handles dry, clean, and free of oil or fuel mixture. S Keep fuel and oil caps, screws, and fas- teners securely tightened. S Use only Poulan accessories and replace- ment parts as recommended. HANDLE FUEL WITH CAUTION S Do not smoke while handling fuel or while operating the saw.
wood closes in and pinches the moving saw chain in the cut along the top of the guide bar and the saw chain is suddenly stopped. This sudden stopping of the chain results in a reversal of the chain force used to cut wood and causes the saw to move in the opposite direction of the chain rotation.
Page 5
WARNING: The following features are included on your saw to help reduce the hazard of kickback; however, such features will not totally eliminate this danger. As a chain saw user, do not rely only on safety de- vices. You must follow all safety precau- tions, instructions, and maintenance in this manual to help avoid kickback and other forces which can result in serious injury.
MODEL P3818 952044418 NOTE: If this saw is to be used for com- mercial logging, a chain brake is required and shall not be removed or otherwise dis- abled to comply with Federal OSHA Regula- tions for Commercial Logging. WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer,...
Page 7
screw. Locate this adjustment before you begin mounting the bar onto the saw. See following illustration. Inside view of clutch cover Adjustment located on clutch cover 4. Turn the adjusting screw by hand coun- terclockwise until the adjusting pin just touches the stop.
to ensure all links are in bar groove. 4. Lift up tip of guide bar to check for sag. Release tip of guide bar, then turn ad- justing screw turn clockwise. Repeat until sag does not exist. Adjusting Screw - - Turn 5.
Poulan oil resists high temperature thinning. If Poulan bar and chain oil is not available, use a good grade SAE 30 oil. S Never use waste oil for bar and chain lubri- cation.
WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within manual. Avoid contact with the muffler. A hot muffler can cause serious burns. To stop the engine move the ON/STOP switch to the STOP position.
Page 11
handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723. CHAIN BRAKE WARNING: If the brake band is worn too thin it may break when the chain brake is triggered.
S The lean of the tree. The lean of a tree might not be apparent due to uneven or sloping terrain. Use a plumb or level to de- termine the direction of tree lean. S Weight and branches on one side. S Surrounding trees and obstacles.
start the saw and carefully reenter the cut. To avoid kickback and chain damage, do not use a metal wedge. Do not attempt to restart your saw when it is pinched or hung in a log. Use a wedge to remove pinched saw Turn saw OFF and use a plastic or wooden wedge to force cut open.
If any dealer other than an authorized service dealer performs work on the product, Poulan may not pay for repairs under warranty. It is your responsibility to maintain and perform general mainte- nance.
Page 15
to appear under the saw after engine stops. Do not confuse this with a leaking oil tank. S ON/STOP Switch - - Ensure ON/STOP switch functions properly by moving the switch to the STOP position. Make sure en- gine stops; then restart engine and continue. S Fuel Tank - - Do not use saw if fuel tank shows signs of damage or leaks.
Cylinder Air Filter Cover Cover Air Filter INSPECT MUFFLER AND SPARK ARRESTING SCREEN As the unit is used, carbon deposits build up on the muffler and spark arresting screen, and must be removed to avoid creating a fire hazard or affecting engine performance. Replace the spark arresting screen if breaks occur.
File Holder File 90˚ Cutter Depth Gauge S Align the 30˚ file holder marks paral- lel with the bar and to the center of the chain. Cutter 30˚ Cutter File Holder Line S Sharpen cutters on one side of the chain first.
Page 18
Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer. Poulan/WEED EATER 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel stabilizer to your fuel tank.
WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit. TROUBLE CAUSE Engine will not 1. Ignition switch off. start or will run 2. Engine flooded. only a few seconds after 3.
This is a limited warranty within the meaning of that term as defined in the Magnuson- - Moss Act of 1975. The policy of Poulan is to continuously im- prove its products. Therefore, Poulan re- serves the right to change, modify, or discon-...
Poulan servicing center. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center, call Poulan at 1- -800- -554- -6723, or send e-mail correspondence emission.warranty@ HCOP- -emission.com. WARRANTY PE- RIOD: Any warranted part which is not...