Page 2
Planar Systems Inc. is fully in support of and compliant with EU Directive 2002/95/EC for applicable products within its scope. A Planar part number will be modifi ed with an “LF” suffi x designation to indicate RoHS compliance, as shown on the part number label affi xed to the display and on the box containing the display.
❑ Do not operate the product under the following conditions: - Extremely hot, cold or humid environment. - Areas susceptible to excessive dust and dirt. - Near any appliance generating a strong magnetic fi eld. - In direct sunlight. LB2650W User’s Guide (020-0973-00 Rev. A)
Introduction About Planar’s LB2650W The LB2650W products all have a 26" diagonal fl at panel screen with an active matrix, thin-fi lm transistor (TFT) liquid crystal display (LCD). Features include: ❑ Dual signal input: Analog VGA and Digital DVI (future models will also include an additional DVI port).
Package Overview LCD Display VGA Signal Cable Quick Start Guide HDMI to DVI Signal Cables North American Power Cord (Please order p/n 903-0467-00 for European style cord) LB2650W User’s Guide (020-0973-00 Rev. A)
Page 8
1920 x 1200 resolution and make sure the timing of the display mode is compatible with the LCD panel. “Video Modes” of this LCD panel are listed in the appendices for your reference. LB2650W User’s Guide (Figure 1.1) (020-0973-00 Rev. A)
Page 9
Figure 1.1 DVI-HDMI DVI Cable (on future models) LB2650W User’s Guide (020-0973-00 Rev. A)
2. Choose the adjustment items by pressing the “Select/Auto” button. 3. Adjust the value of the adjustment items by pressing the “ 4. The OSD menu will automatically close, if you have left it idle for a pre-set amount of time. LB2650W User’s Guide ” button. (020-0973-00 Rev. A)
Menu under input Attention Firmware revision may have been updated into a latest version while the version number shown on information item in OSD menu will stay as Ver 1 Information OSD Figure 2-3 LB2650W User’s Guide (020-0973-00 Rev. A)
Adjust the vertical image position. Analog Input Only) CLOCK (D-SUB or DVI-I Adjust the sync frequency of internal pixel clock. Analog Input Only) PHASE Adjust the value for improve display focus. (D-SUB or DVI-I Analog Input LB2650W User’s Guide (020-0973-00 Rev. A)
Page 14
LB2650W User’s Guide Only) Choose different color temperature (9300K, 7500K, sRGB, USER). Color Temperature Default is USER. USER mode adjustable. Adjust the contrast and brightness of each color of the white balance. GREEN Allows you to adjust the Red/Green/Blue color gain.
Page 15
NO SIGNAL No signal OSD shall be shown after around 0.5sec from video mode detection. This OSD shall be turned off after 5 seconds automatically, or by “EXIT” key. Then LB2650W User’s Guide (020-0973-00 Rev. A)
Target color coordinates Color Temp. u’ v’ LB2650W User’s Guide change to power saving mode. If direction key is pressed during power saving mode, this warning OSD is opened again. This function gives warning about input resolution or refresh rate that the monitor cannot display.
The monitor will show an “OSD Lock Out” message, showing time as “OSD TURN OFF” setting, and the message be show again by any button, also any button exit this message, but “Power” button no action. Figure 2-4 Only repeat this step to unlock. Only repeat this step to unlock. LB2650W User’s Guide (020-0973-00 Rev. A)
Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or visit Planar Support at www.planar.com/support. See support contact information on rear cover. PROBLEM: Picture is unclear and unstable.
Note: Mode 640x350, 640x400 and 720x400 is centered in the middle of the display and cannot be expanded to full screen. Cosmetic Specifi cation Disclaimer: Planar’s cosmetic specifi cation shall match the cosmetic specifi cation authored by the TFT panel manufacturer. Products that contain pixel defects shall not be deemed unsatisfactory whose pixel defects are less than those stipulated by the TFT panel manufacturer.
Support and Service Planar is a US company based in Beaverton, Oregon and Espoo, Finland with a worldwide sales distribution network. Visit Planar at http://www.planar.com/support for product registration, operations manuals, line drawings, touch screen drivers, warranty information and access to Planar’s Technical Library for online troubleshooting.