Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planar LC1713R
Summary of Contents for Planar LC1713R
- Page 1 LC17 LC19 SERIES High-Brightness LCD Monitors USER’S GUIDE www.planar.com...
- Page 2 A Planar part number will be modifi ed with an “LF” suffi x designation to indicate RoHS compliance, as shown on the part number label affi xed to the display and on the box containing the display.
-
Page 3: Table Of Contents
Table of Contents Usage Notice Safety and Use Precautions ......... 4 Introduction About the LC17 and LC19 . -
Page 4: Usage Notice
• Use only a dry soft cloth or clean room wiper when cleaning the LCD panel surface. • Use a soft cloth moistened with mild detergent to clean the monitor housing. • Use only a high-quality and safety-approved 12V power supply. -
Page 5: Introduction
The LC17 and LC19 are high performance monitors designed for demanding applications. The monitor consists of a 17" or 19” diagonal flat panel liquid crystal display (LCD) housed in a metal enclosure with an integrated ambient light sensor to facilitate automatic brightness control. -
Page 6: Package Overview
Package Overview LC17/LC19 VGA Signal Cable Composite Video Cable 80W Power Adapter LC17 and LC19 User’s Guide LC17/LC19 with IR Touchscreen DVI-D Signal Cable S-Video Cable Quick Start Guide North America Power Cable European Power Cable (020-0599-00B) -
Page 7: Installation
Installation Product Overview • Front View • Rear View LC17 and LC19 User’s Guide (020-0599-00B) -
Page 8: Connector Descriptions
Connector View Connector Descriptions 1. Video Interface Connector - Standard D-sub Analog; 15-pin D-sub connector 2. DVI-D 3. NTSC/PALBNC connector 75 ohm input, female composite 4. S-Video input 5. Audio Input - 5P ST/LEAD A71-5AYLT1 LINE, 1.059F2.014 6. Audio Output - SMP-04V-BC Black (Manufacturer is JSP) 7. -
Page 9: Mounting
The LC17 and LC19 can be mounted in two manners: rear 100 mm VESA mount and side mounting holes. M4 threaded holes are provided in the sides of the monitor housing for mounting purposes. The blind holes will accommodate 10 mm long screws. See the mechanical outline drawing (LC17: 076-0626-00 and LC19: 076-0627-00) at www.planar.com/support for details. -
Page 10: Start Your Installation
Start Your Installation Connecting the Display (Figure 1.0) To configure the monitor, please refer to the following figure and procedures. 1. Be sure the computer or video source is turned off. 2. Connect the 12V DC power(1.0). During initial turn on with no video applied, the display will automatically power on with a self test pattern displayed. -
Page 11: User Controls
User Controls Control Buttons Displays the OSD menus 1. Decreases the value of the adjustment items. 2. Decreases the minimum brightness limit of the display image. 1. Increases the value of the adjustment items. 2. Increases the minimum brightness limit of the display image. -
Page 12: How To Use The Osd Menus
How to Use the OSD Menus 1. Press the "Menu" button to pop up the on-screen menu and to select between the four main menus. 2. Choose the adjustment items by pressing the "Select/Auto" button. 3. Adjust the value of the adjustment items by pressing the "+" or "-" button. 4. -
Page 13: On-Screen Display Menus
On-Screen Display Menus LC17 and LC19 User’s Guide (020-0599-00B) -
Page 14: Brightness Control
Brightness Control The brightness of the monitor may be controlled automatically or manually, and the minimum brightness is adjustable. By default, the monitor is configured for automatic brightness control with a minimum brightness setting of approximately 150 cd/m Automatic Brightness Control In automatic brightness control mode, a photo sensor measures the ambient lighting condition (the illuminance). -
Page 15: Manual Brightness Control
To LC17 or LC19 Reference Design for Remote Photo Diode Brightness Control Manual Brightness Control In manual brightness control mode, an externally supplied voltage determines the monitor brightness. To use manual brightness control mode instead of the default automatic brightness control mode: 1. - Page 16 The graph below shows the typical factory set response to the DIM_INPUT voltage when in manual brightness control mode. LC17 and LC19 User’s Guide (020-0599-00B)
-
Page 17: Minimum Brightness Limit
Minimum Brightness Limit The factory set minimum brightness is approximately 150 cd/m . In most applications the factory setting is desired to maintain the widest dimming range possible. But for applications where 300 cd/m is too low but some dimming is still desired, the minimum brightness limit may be increased. The OSD controls are used to access and change the minimum brightness limit setting, as described in the User Controls section of this manual. -
Page 18: Maximum Brightness Mode
2. To set the minimum brightness visually, one may set the dimming to a minimum (by covering the photo sensor on the front of the monitor if in automatic brightness control mode, or by setting the DIM_INPUT to 5V if in manual brightness control mode) and then adjust the OSD setting to visually give the desired result. -
Page 19: Specifications
Specifications Electrical and Optical SPECIFICATIONS 997-3361-00LF Planar Part Number Compensated TN, Full color TFT AMLCD Display Type SXGA (1280 x 1024), XGA, SVGA, VGA Video Modes 338mm x 270mm (17” diagonal) Image Area Video Input DVI-D, 15-pin VGA, S-Video, Composite... -
Page 20: Mechanical And Environmental
Mechanical and Environmental Parameter Operating Temperature Operating Humidity Storage Temperature Storage Humidity Active Area Surface Treatment Weight (w/touchscreen) Random sweep vibration, non-operating Audio The LC17 and LC19 are both equipped with a 1W per channel audio circuit. Input and output jacks are provided. -
Page 21: Reliability And Life
Reliability and Life Parameter Mean Time Between Failures Time to 50% brightness decay from initial brightness Safety and Regulatory Certifications A. FCC Certification FCC Part 15, Subpart B, Class B - Conducted and Radiated Tests B. CE Certification C. RoHS Directive 2002/95/EC, 2005/618/EC Ammendment Emission EN 55022:1998+A1:2000+A2:2003;... -
Page 22: Available Options And Replacement Components
Available Options and Replacement Components 12V Power Supply European AC cord NA AC cord Remote Dimming Cable VGA Cable DVI-D Cable LC17 and LC19 User’s Guide 902-0156-XX 903-0467-XX 903-0466-XX 903-0612-XX 903-0468-XX 903-0602-XX (020-0599-00B) -
Page 23: Cooling Kit
The fans' speed is governed by a temperature sensor adjacent to the photo sensor that is mounted on the front of the monitor. At temperatures above 15°C the fans will turn on at low speed and reach maximum speed at 25°C, thus minimizing the effects of sun loading and high temperatures. -
Page 24: Ir Touchscreen
Gloved hand use is OK. Set Up 1. Refer to Planar mechanical outline drawing for the mounting hole locations. 2. Connect the USB cable from display to USB port on computer. 3. Power on computer and install the IR touchscreen driver found on the provided CD. Follow instructions to calibrate the touchscreen. -
Page 25: Capacitive Touchscreen
ITO on the touched surface. Gloved hand use is OK. Set Up 1. Refer to Planar mechanical outline drawing for the mounting hole locations (Drawing #076-0655-00) 2. Connect the USB cable from display to USB port on computer 3. -
Page 26: Appendix
If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local stat or visit Planar Support at www.Planar.com/support. See support contact information on rear cover. For all video image problems, first try using the Auto-Adjustment in the OSD menu Problem: No image appears on screen. -
Page 27: Mechanical Outline
Properties" in the Control Panel folder. Faint Horizontal Dark Lines Across the Screen This display is directly backlit by cold cathode fluorescent lamps. Slight brightness nonuniformity is normal. Mechanical Outline See mechanical outline drawing on www.planar.com/support LC17 and LC19 User’s Guide (020-0599-00B) -
Page 28: Support And Service
Support and Service Planar is a US company based in Beaverton, Oregon and Espoo, Finland with a worldwide sales distribution network. Visit Planar at http://www.planar.com/support for product registration, operations manuals, line drawings, touch screen drivers, warranty information and access to Planar’s Technical Library for online troubleshooting. - Page 29 Email: IntlTech_Support@Planar.com Hours: M-F, 7am-4pm CET © 2008 Planar Systems, Inc. 8/08 Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.