Learning Mode: Programming Signals From Other Remote Controls - Pioneer VSX-D710S Operating Instructions Manual

Controlling the Rest of Your System
Learning Mode: Programming
Signals from other Remote
Controls
If preset codes are not available for your component(s),
or the available preset codes do not operate correctly,
you can use this function to program in signals from the
remote control(s) of your other component(s). This
operation can also be used after recalling a preset code
to program additional operations not covered in the
preset codes.
LED
1 Press SETUP and hold for three seconds.
The LED on the remote control will light for two
seconds.
To cancel the Learning mode at any time
Press .
SETUP
The remote control will also return to the previous
mode after thirty seconds of inactivity.
2 VSX-D850S only: Use the @ # buttons to
select the Learning mode.
The Learning mode is indicated by the Learning icon
(LEARN) in the remote' s LCD display.
3 Press the MULTI CONTROL button for the
component you want to control
4 VSX-D710S/D810S: Press and hold the
RECEIVER
the Learning mode.
The LED lights steadily.
To cancel LEARNING setup mode
Press
SETUP
If no commands are entered within thirty seconds the
remote will revert to its previous mode.
38
En
4
RECEIVER
SOURCE
DVD TV VCR CD-R
3
MULTI CONTROL
RCV CD TUN TVC
1 2 3
MIDNIGHT 5.1 / 7.1 ATT
4 5 6
EFFECT
7 8 9
10 DISC
0
ENTER
DTV INFO MPX/RETURN D.ACCESS GUIDE
¶ 3
7 8
BAND CLASS
DTV ON/OFF DTV MENU
1 ¡ 4 ¢
2 /DTS DSP SIGNAL SELECT
TEST TONE
CH SELECT CH LEVEL FUNCTION
1,7
LOUDNESS MUTING
FL DIMMER SETUP
TUNE
ST ST
2
ENTER
TUNE
VSX-D850S only
CHANNEL
VOLUME MASTER VOLUME
MENU
TVFUNC
TV
TV CONTROL
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
button for two seconds to start
for one second.
5 Point the two remote controls towards each
other. Press the button to be learned on this
receiver's remote control (for example the 3
[play] button).
Point the remote controls directly at each other, about
1-2 inches apart, and press the button on the remote
control for the operation you want to program. The
LED flashes rapidly. For VSX-D850S, the LEARN icon
blinking.
6 Press the corresponding button on the other
VSX-D710S/
remote control to be taught to this receiver's
D810S only
remote control (in the above example the 3
[play] button).
Point the remote controls toward each other.
Press the button on the other remote control
corresponding to the operation you wish to program.
The LED on this receiver' s remote will go out and
then resume a steady light if the operation is learned.
(For VSX-D850S model the LEARN icon will light
steadily and the LCD display will show "OK" if the
operation has been learned.) If the operation hasn't
been learned for some reason the LED will blink for
three seconds and then light steadily. (For VSX-
D850S model the LCD will display "error" if the
operation hasn't been learned.)
If this happens press the teaching key repeatedly,
varying the distances between the remotes, until you
see the LED on this unit' s remote light steadily,
without blinking first.
To program additional operations for the current
component
Repeat steps 5 and 6.
To program operations for another component
Repeat steps 2 through 6 (VSX-D850S).
Repeat steps 3 through 6 (VSX-D710S/D810S).
7 Press and hold SETUP for one second to exit
the LEARNING setup mode.
After thirty seconds of inactivity the remote control
will automatically leave the LEARNING mode and
revert to its previous mode.
MEMO:
• Some commands from other remote controls cannot
be learned, but in most cases the remotes just need to
be moved closer together or farther apart.
• Certain buttons represent modes that cannot be
learned from other remote controls. These include:
RCV, CH SELECT, CH LEVEL, FUNCTION
LOUDNESS, FL DIMMER, and MUTING.
• TV CONTROL buttons ( TV
FUNC ) can only be learned in TV & TVC mode.
1 - 2 inches
, VOL +/-, and TV