Switching The Speaker Impedance; Power Cord Caution; Specifications - Pioneer VSX-516 Operating Instructions Manual

Additional information

Switching the speaker impedance

We recommend using speakers of 8Ω with this
system, but it is possible to switch the imped-
ance setting if you plan to use speakers with a
6Ω impedance rating.
• With the receiver in standby, press
STANDBY/ON while holding down the
SPEAKERS button.
Each time you do this, you switch between the
impedance settings:
• SP 6 OHM – Use this setting if your
speakers are rated at 6Ω.
• SP 8 OHM – Use this setting if your
speakers are rated at 8Ω or more.

Power cord caution

Handle the power cord by the plug. Do not pull
out the plug by tugging the cord and never
touch the power cord when your hands are wet
as this could cause a short circuit or an electric
shock. Do not place the unit, a piece of
furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it
with other cords. The power cords should be
routed such that they are not likely to be
stepped on. A damaged power cord can cause
a fire or give you an electrical shock. Check the
power cord once in a while. When you find it
damaged, ask your nearest Pioneer authorized
service center or your dealer for a replacement
Note
1 Continuous average power output of 110 watts* per channel, min., at 8ohms, from 20 Hz to 20 000 Hz with no more than 0.7
%** total harmonic distortion (front).
* Measured pursuant to the Federal Trade Commission's Trade Regulation rule on Power Output Claims for Amplifiers.
** Measured by Audio Spectrum Analyzer.

Specifications

Amplifier section
• Continuous power output (stereo)
Front. . 100 W (20 to 20 000 Hz, THD 0.7 %, 8
• Continuous power output (surround)
Front. . . . . 100 W per channel (1 kHz, 1.0 %, 8
Center . . . . . . . . . . . . . . 100 W (1 kHz, 1.0 %, 8
Surround . . . . . . . . . . . . . . . . . 100 W per channel
Surround Back . . . . . . . . . . . . 100 W per channel
Audio section
• Input (Sensitivity/Impedance)
CD, DVR/VCR, CD-R/TAPE/MD,
DVD/LD, TV/SAT . . . . . . . . . . . . . . . 200 mV/47 k
• Frequency response
CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD,
TV/SAT . . . . . . . . . . . . . . 5 Hz to 100 000 Hz
• Output (Level/Impedance)
DVR/VCR REC, CD-R/TAPE/
MD REC . . . . . . . . . . . . . . . . . . . . . . 200 mV/2.2 k
• Tone control
Bass . . . . . . . . . . . . . . . . . . . . . . . .± 6 dB (100 Hz)
Treble . . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (10 kHz)
Loudness . . . . . . +10 dB/+5 dB (100 Hz/10 kHz)
• Signal-to-Noise Ratio (IHF, short circuited,
A network)
CD, DVR/VCR, CD-R/TAPE/MD,
DVD/LD, TV/SAT . . . . . . . . . . . . . . . . . . . . . . 96 dB
• Signal-to Noise Ratio [EIA, at 1 W (1 kHz)]
CD, DVR/VCR, CD-R/TAPE/MD,
DVD/LD, TV/SAT . . . . . . . . . . . . . . . . . . . . . . 79 dB
Ω )
Ω
Ω
(1 kHz, 1.0 %, 8 Ω
Ω
(1 kHz, 1.0 %, 8
Ω
dB
Ω
(at volume level –50 dB)
10
1
)
)
)
)
37
En