Selecting The Analog Or Digital Input Mode - JVC RX-8010RBK Service Manual

2. Press CONTROL UP 5/DOWN ∞
to select the appropriate digital
terminal settings.
• Each time you press the buttons, the
display changes to show the following:
When the DGTL COAX (DIGITAL 1) is set to "DVD"
2: CD 3: TV (or DBS * ) 4: CDR "
2: CD 3: TV (or DBS * ) 4: MD ** "
2: CD 3: MD ** 4: CDR "
2: MD** 3: TV (or DBS * ) 4: CDR "
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to "MD" **
2: CD 3: TV (or DBS * ) 4: DVD "
2: CD 3: DVD 4: CDR "
2: DVD 3: TV (or DBS * ) 4: CDR "
2: CD 3: TV (or DBS * ) 4: CDR "
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to "CDR"
2: MD ** 3: TV (or DBS * ) 4: DVD "
2: CD 3: TV (or DBS * ) 4: DVD "
2: CD 3: TV (or DBS * ) 4: MD ** "
2: CD 3: MD ** 4: DVD "
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to "TV" or "DBS"
2: CD 3: MD ** 4: CDR " 2: MD ** 3: DVD 4: CDR "
2: CD 3: DVD 4: CDR " 2: CD 3: DVD 4: MD ** "
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to "CD"
2: DVD 3: TV (or DBS * ) 4: MD ** "
2: DVD 3: MD ** 4: CDR "
2: MD ** 3: TV (or DBS * ) 4: CDR "
2: DVD 3: TV (or DBS * ) 4: CDR "
(back to the beginning)
* If you have changed the source name from "TV" to "DBS,"
"DBS" appears (see page 16).
**
Change the source name to "MD" for TAPE/MD jacks when you
use an MD recorder (see page 16).
Note:
When shipped from the factory, the DIGITAL IN terminals have been
set for use with the following components.
• DIGITAL 1 (coaxial): For DVD player
• DIGITAL 2 (optical): For CD player
• DIGITAL 3 (optical): For digital TV broadcast tuner
• DIGITAL 4 (optical): For CD recorder
CONTROL
Selecting the Analog or Digital Input
DOWN UP
Mode
When you have connected digital source components using the
digital terminals (see page 8), you need to change the input mode for
these components to the appropriate digital input mode correctly —
DGTL AUTO, DGTL DTS, or DGTL D.D.
Before you start, remember...
• The digital input (DIGITAL IN) terminal setting should be
correctly done for the sources you want to select the digital
input mode for. Without setting this digital input terminal
correctly, you cannot change the input mode from analog input to
digital input even if you follow the procedure below.
On the front panel:
1. Press one of the source selecting button (DVD, TV
SOUND/DBS, CD, CDR, or TAPE/MD)* for which
you want to change the input mode.
The lamp on the front panel button for selected source lights up.
Note:
* Among the source listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See "Digital Input (DIGITAL IN) Terminal Setting"
on page 19.)
2. Press INPUT ANALOG/DIGITAL
(INPUT ATT) briefly to change
the input mode.
• Each time you press the button, the input
mode changes as follows.
DGTL AUTO
(Digital)
DGTL AUTO: Select this for the digital input mode. The
ANALOG:
When selecting "DGTL AUTO," following indicators showing
detected signals light up on the display.
LINEAR PCM
DIGITAL
DVD MULTI DVD VCR 2 VIDEO TV SOUND/DBS
VCR 1
SOURCE NAME
PHONO CD CDR TAPE / MD USB AUDIO
SOURCE NAME
ANALOG
receiver automatically detects the incoming
signal.
Select this for the analog input mode.
always lights up.
ANALOG
: Always lights up.
: • Lights up when Linear PCM signals come in.
• The frame flashes when detecting signals.
• LINEAR PCM without frame flashes when
PCM signals are not recognized.
: Lights up when Dolby Digital signals come in.
: Lights up when DTS Digital Surround signals
come in.
Continued to the next page.
FM / AM
INPUT
ANALOG/DIGITAL
INPUT ATT
20