Panasonic BT-M2090Y Service Manual page 8

0)
MEMORY MODE
A set of picture settings can be programmed in memory
for quick recall when necessary.
Recall/release of memory mode--------
Press the MEMORY MODE switch to recall a set of picture settings
programmed in memory.
Pressing the switch locks the functions of the front-panel PHASE,
CHROMA, BRIGHT, CONTRAST controls, and remote-control picture
adjustments not to be operated.
Press egein to release memory mode.
Setting programming of the picture being monitored-
The settings of the picture being monitored cen be programmed In
memory.
Settings programmable in memory mode:-------------
• Settings of the CONTRAST, BRIGHT, CHROMA and PHASE controls on the
front panel
• On-screen menu function settings (except RGB/COMPO(SDI))
• Remote-control picture adjustment settings
1.
Check the MEMORY MODE switch is off.
2.
Press the MENU button.
3.
Press the • or
T
button to select MEMORY MODE.
Then press the ENTER button.
4. •
Press the ENTER button to programme.
• Press the -<II or II>- b utton to cancel.
Revision of memory mode-----------
Programmed picture settings can be revised if necessary.
1.
Press the MEMORY MODE switch to activate memory mode.
2.
Press the MENU button to call up display (jJ on screen.
g
• lf you attempt to operate a locked
function, "MEMORY MODE ONII"
appears on screen for approx.
2
seconds to indicate the function
cannot be operated.
g
• Programmed picture settings are
kept in memory after the power is
turned off.
(MEMORY MODE)
AnJ you sure ?
"Yes" then
I]!!!!)
"Na" then lj or
8
g
• No matter what video signal is Input,
all items appear on screen.
However, depending on the type of
input video signal, some functions
might not operate even if their
settings are made.
(MEMORY MODE REVISE>
~PICTURE ADJUSTMENT
ASPECT RAT 10 :4-3
FILTER SELECT :COMB
PEAK I NG FREQ. :2.6MHZ
PEAKING LEVEL :GdB
AFC :NORMAL
COLOR TEMP. :6500
NTSC SETUP :O
ca.,PO.LEVEL :SMPTE
llliDl
:e
(jJ
MEMORY MODE {continued)
3.
Press the • or
T
button to select a function to be revised.
Press the ENTER button after selecting PICTURE ADJUSTMENT to call up
display
III.
After making all settings on screen, press the MENU button to make display (jJ
appear.
4.
Press the -<II or
II>-
b utton to change the set level.
Adjustable CONTRAST, BRIGHT, CHROMA or PHASE range depends on each
set level previously stored in memory. MAX appears to indicate maximum level
that cannot be increased. MIN appears to indicate minimum level that cannot be
decreased.
evariable setting range
Function Variable setting range Default set level
PICTURE
CONTRAST -2010 +20 0
ADJUST-
BRIGHT ·20to +20 0
CHROMA -20 to +20 0
MENT
PHASE -20 to +20 0
ASPECT RATIO 4:3 16:9 4:3
FILTER SELECT COMB BOTH NOTCH COMB
PEAKING FREQ. 2.6MHz 5.0MHz 2.6MHz
PEAKING LEVEL OdB + 1dB • • • +9dB OdB
AFC NORMAL FAST SLOW NORMAL
COLOR TEMP. 9300
6500 6500
NTSCSETUP 0 7.5 0
COMPO. LEVEL SMPTE BETAOO BETA75 SMPTE
5.
With display [I] on screen, press the MENU button to make display[]] appear.
ePress the ENTER button to programme.
ePress the -<II or .. button to cancel.
<MEMORY MODE
~CONTRAST
BRIGHT
CHRa.,A
PHASE
lllleil
g
II]
REVISE>
:O
:0
:O
:O
:ea
• If the ENTER button Is pressed alter
a function other than PICTURE
ADJUSTMENT Is selected, the on-
screen display changes in1o a
single•line one. To select another
functioo alter making a change In
function, press the MENU button to
restore display [I].
<MEMORY MODE REVISE)
Are you sure ?
"Yes"
thenl!!fili!I
"No" then~or8
rn
a
I
3
"
C
~