http://www.xiaoyu163.com SPECIFICATIONS 3 7 63 1515 0 MAIN UNIT CX-LEM70 CD PLAYER Laser Semiconductor laser (λ = 780 nm) TUNER D/A converter 1 bit dual FM tuning range 87.5 MHz to 108 MHz Signal-to-noise ratio 88 dB (1 kHz, 0 dB) FM usable sensitivity (IHF) 13.2 dBf Harmonic distortion...
http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING 3 7 63 1515 0 CAUTION This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
http://www.xiaoyu163.com TRANSISTOR ILLUSTRATION 3 7 63 1515 0 E C B E C B B C E B C E 2SA1296GR 2SA1980G 2SB1677 2SB1370E KTC3198GR 2SA1981Y 2SD2619 2SC2240(GR/BL) 2SD655E G D S E C B 2SC4115SRS 2SK2158 2SK3053 2SK360E L 13942296513 2SA1235F DTC144EKA 2SA1514K(S)
http://www.xiaoyu163.com IC DESCRIPTION IC, LC78622NE 3 7 63 1515 0 Description Pin No. Pin Name DEFI Defect detection signal (DEF) input. ("L" is applied when not used.) For PLL/Test input. (Connected to 0V) Phase comparison output to control the external VCO. VVSS ...
Page 28
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Description Pin No. O-RCH Rch output. RVDD Rch power supply. MUTE-R Rch muting output. (Not used) XVDD Power supply of crystal oscillator. XOUT For the connection of a 16.934MHz crystal oscillator. XVSS ...
Page 29
http://www.xiaoyu163.com IC, LA9241ML 3 7 63 1515 0 Description Pin No. Pin Name For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF FIN2 signal and subtraction from it create an EF signal. FIN1 For the connection of the pickup photodiode. For the connection of the pickup photodiode.
Page 30
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description SLOF Sled servo off control input. CV CLV error signal input from the DSP. RFSM RF output. RFS Sets the RF gain and the EFM signal's 3T compensation constant together with the RFSM pin. The SLC (slice level control) signal is output to control the DSP's data slice level of the RF waveform.
Page 31
http://www.xiaoyu163.com IC, LC876564V-5Y22 3 7 63 1515 0 Pin No. Pin Name Description O-COIN CD IC control data output. O-CDCONT CD block power ON / OFF control output. O-OPEN (CD) CD tray open data output. O-CLOSE (CD) CD tray close data output. O-OPEN (CT) Deck open / close output.
Page 32
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description O-LED (TU) Tuner function LED ON / OFF. O-LED (AU) AUX function LED ON / OFF. O-LED (TA) Tape function LED ON / OFF. O-LED (PW) Power function LED ON / OFF. (Light up : ECO standby) O-ECO Relay switch ON / OFF output.
http://www.xiaoyu163.com ADJUSTMENT (TUNER / DECK / CD / FL) <TUNER SECTION> 3 7 63 1515 0 PWB TUNER PARTS SIDE PATTERN SIDE L807 L804 JW970 IC991 L801 L802 L951 IC801 CN991 12 11 CN991 1. VT Check (AM) Requirement DIGITAL MULTIMETER Measuring Device: Digital Multimeter Test Point: VT, GND (1) Adjust the reception frequency of the set to 1710 kHz.
Page 34
http://www.xiaoyu163.com <AM Adjustment> 3 7 63 1515 0 For AM adjustment, do wiring and connection as in the following. 60cm Standard Signal Generator Connect to the respective measuring device Fig. 2 4. IF adjustment (AM) OSCILLOSCOPE Requirement Measuring Device: Oscilloscope and Millivoltmeter Test Point: Lch, Rch, GND Adjustment Point: L802 (1) Adjust the setting of Standard Signal Generator (hereinafter S.S.G) to 1000 kHz of 30 % variation.
Page 35
http://www.xiaoyu163.com <FM Adjustment> 3 7 63 1515 0 For adjusting FM, do wiring and connection as in the following. Standard Signal Generator Connect to the respective measuring device 7. Tracking Adjustment (FM) AC MILLIVOLTMETER Requirement Measuring device: Millivoltmeter Test Point: Lch, Rch, GND Adjustment Point: L904 (1) Adjust the S.S.G setting to 98.0 MHz, 75 kHz variation and reduce the output level all the way.
Page 36
http://www.xiaoyu163.com <DECK SECTION> 3 7 63 1515 0 PWB MAIN PATTERN SIDE SFR352 SFR351 SP OUT L 13942296513 Prepare the following before adjusting the deck. Preparation Measuring Device: Audio Signal Generator / Attenuator / Wow & Flutter Meter (Frequency Counter) / Oscilloscope / Millivolmeter / Dummy Load (6 ohm).
Page 37
http://www.xiaoyu163.com 1. Checking Tape Speed 3 7 63 1515 0 Requirements Test Tape: TTA-100 (3 kHz) Test Point: Lch, Rch, GND Adjustment Point: SFR1 1) Insert the test tape (TTA-100), FWD play back the centre of the tape and check that the speed is 3,000 Hz ± 45 Hz. 2) RVS playback and check that ±...
Page 38
http://www.xiaoyu163.com <CD SECTION> 3 7 63 1515 0 PWB CD R546 RIOP SFR501 FE IC501 IC651 L 13942296513 CD Adjustment Method Perform the adjustments after the machine enters the test mode. Place the CD mechanism on level ground. Equipment and tools required Measuring equipment: Oscilloscope (Use the probe of 10:1) Digital Multimeter (Use it in the DC Volt range) Jitter meter (Kikusui 6235)
Page 39
http://www.xiaoyu163.com 4. Tracking Balance Check OSCILLOSCOPE 3 7 63 1515 0 1) Connect the test point (TE), (VC) to the oscilloscope. 2) Playback the second track of TCD-782 and press the PAUSE button. OUTPUT 3) Check that the traverse waveforms of the oscilloscope are up and down symmetrical.
http://www.xiaoyu163.com CD TEST MODE 3 7 63 1515 0 1. How to Start the CD Test Mode While pressing the CD FUNCTION button, insert the AC plug to the power outlet. When the test mode started, the message [CD TEST] is displayed. 2.
http://www.xiaoyu163.com MECHANICAL PARTS LIST = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
http://www.xiaoyu163.com COLOR NAME TABLE 3 7 63 1515 0 Basic color symbol Color Basic color symbol Color Basic color symbol Color Black Cream Orange Green Gray Blue Transparent Blue Gold Pink Silver Titan Silver Brown Violet White Transparent White Yellow Transparent Yellow Metallic Blue Light Blue...
http://www.xiaoyu163.com TAPE MECHANISM PARTS LIST 1 / 2 3 7 63 1515 0 REF. NO. PART NO. KANRI DESCRIPTION 8A-ZM1-214-010 PLATE,F STOPPER 8A-ZM1-223-010 SPR-T,LOCK F 8A-ZM1-209-010 GEAR,SLIDE B 8A-ZM1-233-010 FRAME,MAIN BL 8A-ZM1-215-210 LEVER ASSY,SLIDE L 8A-ZM1-217-010 LEVER ASSY,SLIDE R 8A-ZM1-212-010 LEVER,LOCK F 8A-ZM1-208-110 GEAR,SLIDE A...
http://www.xiaoyu163.com TAPE MECHANISM PARTS LIST 2 / 2 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Page 48
http://www.xiaoyu163.com = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
http://www.xiaoyu163.com CD MECHANISM PARTS LIST 1 / 2 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
http://www.xiaoyu163.com CD MECHANISM PARTS LIST 2 / 2 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
http://www.xiaoyu163.com GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) 3 7 63 1515 0 Type.1 Type.4 Insert a flat-bladed screwdriver into the position indicated by the TOOLS arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit and then remove the speaker units.