For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty. Model No. Serial No. (Lot No.)
WARNING To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Explanation of Graphical Symbols: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”...
Outdoor Antenna Power lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
PREPARATIONS Connection Plug in the AC power cord to the AC outlet after all other connections are made. 1 Connect the speakers to the main unit. Connect the right speaker to the SPEAKERS R terminals and the left to the SPEAKERS L terminals. The speaker cords with the stripes go to the 0 terminals.
PARTS AND CONTROLS Main unit 1 cTAPE (REC MUTE) Starts playback. Also used to enter 4-second blank spaces during recording. TUNER/AUX/BAND Selects Radio function and the radio band. Also selects the function of external equipment connected to AUX IN jacks. Starts and pauses CD play.
Remote control Buttons with the same or similar names on the main unit basically have the same function. 1 POWER 2 0–10, +10 CD: selects a track of the specified number. Radio: tunes in the station with the specified preset number.
ADJUSTMENTS BEFORE OPERATION TAPE, TUNER/AUX/BAND, POWER 6STANDBY/ON Power Turning the unit on Press POWER 6 STANDBY/ON (POWER on the remote control). Alternatively, press TAPE, TUNER/AUX/BAND (TUNER/BAND or AUX on the remote control) or CD. Playback will start automatically if a disc or tape is loaded. Turning the unit off Press POWER 6STANDBY/ON again.
CD OPERATIONS This unit plays back finalized CD-R/RW discs as well as audio CDs. Playing a CD 1 Press OPEN to open the disc compartment. Place a disc with the label side up. Then close the disc compartment by pressing OPEN. 2 Press E to start play.
Programmed play Plays back up to 30 selected tracks in programmed order. 1 Hold down SHIFT and press PROGRAM on the remote control in stop mode. "PRGM" flashes on the display. 2 Press the numbered buttons on the remote control to program a track. -To select the 25th track, press +10, +10 and 5.
RADIO OPERATIONS TUNER/ AUX/BAND POWER Manual tuning 1 Press TUNER/AUX/BAND (TUNER/BAND on the remote control) repeatedly to select a band. 2 Press f or g repeatedly to tune in a station. "TUNE" is displayed when a station is tuned in. "1"...
Adjustments To switch to monaural FM reception Hold down SHIFT and press TUNER MODE on the remote control so that "MONO" is displayed. To cancel, repeat the above so that "STEREO" is displayed. Tip: When FM stereo reception is poor, switching to monaural reduces noise.
TAPE PLAYBACK REC/ REC PAUSE SYNCHRO Playback Use only type I (normal) tapes. 1 Press zPUSH EJECT to open the cassette holder. 2 Insert the tape. Insert with the exposed side down and the side to be played facing out from the unit, and press zPUSH EJECT to close the cassette holder.
TAPE RECORDING Basic recording Use only type I (normal) tapes. 1 Press zPUSH EJECT to open the cassette holder. 2 Insert the recording tape. Insert with the exposed side down, and the side to be recorded on facing out from the unit. Press zPUSH EJECT to close the cassette holder.
REC/ REC PAUSE Edited CD recording AI Edit Recording Preparation Prepare a tape that is longer than the CD length. When recording a whole CD, AI Edit Recording takes the length of your tape into account and rearranges the recording order of the tracks if necessary, so that no track is cut short at the end of the side.
8 Hold down SHIFT and press CD EDIT/CHECK once to switch back to side A. 9 Press REC/REC PAUSE once. The tape is rewound to the beginning of side A. "REC MUTE" flashes on the display and the lead segment is played through for 10 seconds, and recording starts.
TIMER OPERATIONS POWER 6STANDBY/ON Sleep timer Turns off the unit automatically after a specified time. 1 Hold down SHIFT and press SLEEP on the remote control. "5" and "SLP" is displayed. 2 Within 6 seconds, press f or g repeatedly to set the sleep timer duration.
Timer recording Timer recording is available only for TUNER and AUX (with an external timer) sources. 1 Hold down SHIFT and press TIMER on the remote control repeatedly so that "5 REC" is displayed. 2 Within 6 seconds, press SET. 3 Press f or g to set the timer-on time, and press SET.
REFERENCE Care and maintenance Occasional care and maintenance of the unit and the software are needed to optimize the performance of your unit. To clean the cabinet Use a soft and dry cloth. If the unit surfaces are extremely dirty, use a soft cloth lightly moistened with mild detergent solution.
Specifications MAIN UNIT CX-LEM20 TUNER FM tuning range 87.5 MHz to 108 MHz FM usable sensitivity (IHF) 13.2 dBf FM antenna terminal 75 ohms (unbalanced) AM tuning range 530 kHz to 1710 kHz (10 kHz step) 531 kHz to 1602 kHz (9 kHz step) AM usable sensitivity 350 µV/m AM antenna...
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.