Safe Operation Practices - Troy-Bilt CS 4265 series Operator's Manual

Important Safe Operation Practices
WARNING:
This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself
and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may
result in personal injury.
When you see this symbol.
WARNING:
Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of California to cause
cancer and birth defects or other reproductive harm.
DANGER:
This machine was built to be operated according to the safe operation practices in this manual. As with any type of power equipment,
carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating fingers, hands, toes and feet and
throwing debris. Failure to observe the following safety instructions could result in serious injury or death.
Training
1. Read, understand, and follow all instructions
on the machine and in the manual(s) before
attempting to assemble and operate.
Keep this manual in a safe place for future
and regular reference and for ordering
replacement parts.
2. Be familiar with all controls and their proper
operation. Know how to stop the machine and
disengage them quickly.
3. Never allow children under 16 years of age to
operate this machine. Children 16 and over
should read and understand the instructions
and safe operation practices in this manual
and on the machine and be trained and
supervised by an adult.
4. Never allow adults to operate this machine
without proper instruction.
5. Keep bystanders, pets, and children at least 75
feet from the machine while it is in operation.
Stop machine if anyone enters the area.
6. Never run an engine indoors or in a poorly
ventilated area. Engine exhaust contains
carbon monoxide, an odorless and deadly gas.
7. Do not put hands and feet near rotating parts
or in the feeding chambers and discharge
opening. Contact with the rotating impeller
can amputate fingers, hands, and feet.
8. Never attempt to unclog either the feed intake
or discharge opening, remove or empty bag,
or inspect and repair the machine while the
engine is running. Shut the engine off and
wait until all moving parts have come to a
complete stop. Disconnect the spark plug wire
and ground it against the engine.
Preparation
1. Thoroughly inspect the area where the
equipment is to be used. Remove all rocks,
bottles, cans, or other foreign objects which
could be picked up or thrown and cause
personal injury or damage to the machine.
2. Always wear safety glasses or safety goggles
during operation and while performing an
adjustment or repair, to protect your eyes.
Thrown objects which ricochet can cause
serious injury to the eyes.
3. Wear sturdy, rough-soled work shoes and
close-fitting slacks and shirts. Loose fitting
clothes or jewelry can be caught in movable
parts. Never operate this machine in bare feet
or sandals. Wear leather work gloves when
feeding material in the chipper chute.
4. Before starting, check all bolts and screws for
proper tightness to be sure the machine is in
safe working condition. Also, visually inspect
machine for any damage at frequent intervals.
5. Maintain or replace safety and instructions
labels, as necessary.
HEED ITS WARNING!
CALIFORNIA PROPOSITION 65
Safe Handling of Gasoline:
To avoid personal injury or property damage use
extreme care in handling gasoline. Gasoline is
extremely flammable and the vapors are explosive.
Serious personal injury can occur when gasoline is
spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
a. Use only an approved gasoline
container.
b. Never fill containers inside a vehicle or
on a truck or trailer bed with a plastic
liner. Always place containers on the
ground away from your vehicle before
filling.
c. When practical, remove gas-powered
equipment from the truck or trailer and
refuel it on the ground. If this is not
possible, then refuel such equipment
on a trailer with a portable container,
rather than from a gasoline dispenser
nozzle.
d. Keep the nozzle in contact with the rim
of the fuel tank or container opening at
all times until fueling is complete. Do
not use a nozzle lock-open device.
e. Extinguish all cigarettes, cigars, pipes
and other sources of ignition.
f. Never fuel machine indoors.
g. Never remove gas cap or add fuel while
the engine is hot or running. Allow
engine to cool at least two minutes
before refueling.
h. Never over fill fuel tank. Fill tank to
no more than ½ inch below bottom
of filler neck to allow space for fuel
expansion.
i. Replace gasoline cap and tighten
securely.
j. If gasoline is spilled, wipe it off the
engine and equipment. Move unit to
another area. Wait 5 minutes before
starting the engine.
k. To reduce fire hazards, keep machine
free of grass, leaves, or other debris
build-up. Clean up oil or fuel spillage
and remove any fuel soaked debris.
l. Never store the machine or fuel
container inside where there is an open
flame, spark or pilot light as on a water
heater, space heater, furnace, clothes
dryer or other gas appliances.
Operation
1. Do not put hands and feet near rotating parts
or in the feeding chambers and discharge
opening. Contact with the rotating impeller
can amputate fingers, hands, and feet.
2. Before starting the machine, make sure
the chipper chute, feed intake, and cutting
chamber are empty and free of all debris.
3. Thoroughly inspect all material to be shredded
and remove any metal, rocks, bottles, cans,
or other foreign objects which could cause
personal injury or damage to the machine.
4. If it becomes necessary to push material
through the shredder hopper, use a small
diameter stick. Do not use your hands or feet.
5. If the impeller strikes a foreign object or if your
machine should start making an unusual noise
or vibration, immediately shut the engine
off. Allow the impeller to come to a complete
stop. Disconnect the spark plug wire, ground it
against the engine and perform the following
steps:
a. Inspect for damage.
b. Repair or replace any damaged parts.
c. Check for any loose parts and tighten
to assure continued safe operation.
6. Do not allow an accumulation of processed
material to build up in the discharge area.
This can prevent proper discharge and result
in kickback of material through the feed
opening.
7. Do not attempt to shred or chip material
larger than specified on the machine or in this
manual. Personal injury or machine damage
could result.
8. Never attempt to unclog either the feed
intake or discharge opening while the engine
is running. Shut the engine off, wait until all
moving parts have stopped, disconnect the
spark plug wire and ground it against the
engine before clearing debris.
9. Never operate without the shredder hopper,
chipper chute, or chute deflector properly
attached to the machine. Never empty or
change discharge bag while the engine is
running.
10. Keep all guards, deflectors and safety devices
in place and operating properly.
11. Keep your face and body back and to the side
of the chipper chute while feeding material
into the machine to avoid accidental kickback
injuries.
12. Never operate this machine without good
visibility or light.
13. Do not operate this machine on a paved,
gravel or non-level surface.
14. Do not operate this machine while under the
influence of alcohol or drugs.
15. Muffler and engine become hot and can cause
a burn. Do not touch.
16. Never pick up or carry machine while the
engine is running.
17. If situations occur which are not covered in
this manual, use care and good judgement.
Contact Customer Support for assistance and
the name of the nearest service dealer.
2
3