Programming The Clearray (Ultraviolet) - Jacuzzi J-315 Installation Manual And Use & Maintenance

L1: Full lock out (disables all spa functions to permit filter cleaning)
L2: Partial lock out
(disables the buttons for jets and light to prevent unautho-
rized use of the spa). In this mode, the skimming/heating
mode continues to operate as programmed. The temperature
display flashes when this function is enabled. Example: the
"F3" skimming/heater cycle was enabled prior to choos-
ing lock mode. The spa continues to perform the "F3" cy-
cle until lock mode is cancelled, allowing another cycle to
be selected.
NOTE: To exit a Lock Mode you will need to re-enter the fil-
tration/heating modes and select a cycle from F1-F6.
I
To set the time of the first skimming/heating cycle connect the
spa to the power supply two minutes before the desired time.
EXAMPLE: If you desire your first skimming/heater cycle to begin
at 10:00 AM turn off power to the spa and turn it back on again at
9:58 AM.
I
Selecting the Circulation Pump Filtration Cycle
Press and hold the Jets pump 1 (
at the same time for 3 seconds to access the circulation pump
programming. Continually press the Warmer (
scroll up through the cycles below. Then select a cycle and press
the Jets pump 1 ( ) button to activate that cycle. Upon press-
ing the jets pump 1 button the system will save your selection,
exit the program menu and return to the main menu.
Note: After 10 seconds the programming screen will revert
back to the temperature if no buttons are pressed. You cannot
have more than one circulation pump cycle activated at a time.
0 hours of circulation per day
4 hours of circulation per day
8 hours of circulation per day (recommended
factory default setting for J335-J375 models)
12 hours of circulation per day
16 hours of circulation per day
20 hours of circulation per day
24 hours of circulation per day
(recommended factory default setting for J315
models)

Programming the Clearray (Ultraviolet)

Programming the CLEARRAY System (U) or Corona Dis-
charge Ozone (O3) (where included)
Press and hold the Jets pump 1 (
ton at the same time for 3 seconds. Scroll pass the circulation
pump programming menus by pressing the Warmer button.
) and Cooler ( ) button
) button to
) and Cooler ( ) but-
Press Press
Press Press
Will select
Will select "03"
"O3" option
option and exit
menu and exit menu
Will take you
Will take you
back to "C0" back to "C0"
After the last cycle, "C6", the LED screen will display "U" or "O3".
If the LED screen is displaying "U" then pressing the Jets pump
1 will change the sanitizing system from "U" to "O3" and exit the
programming menu. If the LED screen is displaying "O3" then
pressing the Jets pump 1 will change the sanitizing system from
"O3" to "U" and exit the programming menu. You will see one of
the two configurations below:
A. C0, C1, C2, C3, C4, C5, C6, U, 365 (duration countdown
timer)
B. C0, C1, C2, C3, C4, C5, C6, O3, =
Note: For the O3 option the "=" disables the duration count-
down timer. If you do not wish to change the option do not
press any buttons and after 10 seconds the display will return
to the main menu.
If the CLEARRAY System has been selected, when the time
allotted has expired (365 days) the display screen will flash
between the water temperature and "blb". At this time the UV
lamp bulb must be replaced, the quartz tube must be cleaned
and the duration countdown timer needs to be reset.
Press Press
Press Press
Press Press
Press Press
Will reset the timer
Will reset the timer
to 365 days and exit
to 365 days and exit
the menu
the menu
I
Resetting the duration countdown timer (CLEARRAY
System only)
Once the duration countdown timer for the CLEARRAY System
has reached zero, you will need to reset it, replace the UV lamp
bulb and clean the quartz tube.
To reset the duration countdown timer:
Press and hold the Jets pump 1 (
ton at the same time for 3 seconds.
Press the Warmer (
If the timer has reached "0", pressing the Jets pump 1 (
button will reset the counter. If the timer is not at "0" pressing
the Jets pump 1 button will not reset it.
Note: If the spa power is interrupted, the duration countdown
timer is not affected. The number of days remaining is stored in
27
Press Press
Press Press
Press Press
Press
Press
Press
Press
Press Press
Press Press
Press Press
Press Press
) and Cooler (
) button until the display shows "0".
Press
Press
Press
Press
) but-
)