Kenwood NX-210(G) Service Manual page 58

NX-210(G)
Item
Panel tuning mode
Low RSSI 1) Adj item: [Aw LRSSI]
at 118dBm Adjust: [***]
adjust *7 2) Adj item:
[AwL LRSSI]→
[Analog [AwL' LRSSI]→
Wide] [AwC LRSSI]→
[AwH' LRSSI]→
[AwH LRSSI]
Adjust: [***]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz/±3kHz)
[NXDN 1) Adj item: [Nv
Very LRSSI]
Narrow] Adjust: [***]
2) Adj item:
[NvL LRSSI]→
[NvL' LRSSI]→
[NvC LRSSI→
[NvH' LRSSI]→
[NvH LRSSI]
Adjust: [***]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz/±1.5kHz)
*7: Because Low RSSI at –118dBm (NXDN Narrow) is adjusted by adjusting Low RSSI at –118dBm (Analog Narrow), it is not necessary to adjust
Low RSSI at –118dBm (NXDN Narrow).
7. High RSSI 1) Adj item: [An
at –80dBm HRSSI]
adjust *8 Adjust: [***]
2) Adj item:
[Analog [AnL HRSSI]→
Narrow] [AnL' HRSSI]→
[AnC HRSSI]→
[AnH' HRSSI]→
[AnH HRSSI]
Adjust: [***]
SSG output:
–80dBm (22.4µV)
(MOD: 1kHz/±1.5kHz)
[Analog 1) Adj item: [Aw HRSSI]
Wide] Adjust: [***]
2) Adj item:
[AwL HRSSI]→
[AwL' HRSSI]→
[AwC HRSSI]→
[AwH' HRSSI]→
[AwH HRSSI]
Adjust: [***]
SSG output:
–80dBm (22.4µV)
(MOD: 1kHz/±3kHz)
58
ADJUSTMENT
Condition
PC test mode
equipment
1) Adj item: [Low RSSI SSG
(Analog Wide)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz/±3kHz)
1) Adj item: [Low RSSI
(NXDN Very Nar-
row)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz/±1.5kHz)
1) Adj item: [High SSG
RSSI (Analog Nar-
row)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
SSG output:
–80dBm (22.4µV)
(MOD: 1kHz/±1.5kHz)
1) Adj item: [High
RSSI (Analog
Wide)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
SSG output:
–80dBm (22.4µV)
(MOD: 1kHz/±3kHz)
Measurement
Test-
Unit Terminal Unit
Panel ANT
Universal
connector
Panel ANT
Universal
connector
Adjustment
Specifi cations /
Parts Method
[Panel tuning mode]
After input signal
from SSG, press
[ ] key to store the
adjustment value.
[PC test mode]
After input signal
from SSG, press
[Apply] button to
store the adjust-
ment value.
Adjust with the
analog signal.
[Panel tuning mode]
After input signal
from SSG, press
[ ] key to store the
adjustment value.
[PC test mode]
After input signal
from SSG, press
[Apply] button to
store the adjust-
ment value.
Remarks