Mitsubishi Electric MR-J4 Instruction Manual page 235

5. PARAMETERS
No./symbol/ Setting
name digit
PB56 Set the vibration frequency for vibration suppression control 2 when the gain
switching is enabled.
VRF21B
When you set a value less than 0.1 Hz, the value will be the same as [Pr. PB52].
Vibration
suppression This parameter will be enabled only when the following conditions are fulfilled.
control 2 -
Vibration
frequency
after gain
switching
Switching during driving may cause a shock. Be sure to switch them after the servo
motor or linear servo motor stops.
Setting range: 0.0 to 300.0
PB57 Set the resonance frequency for vibration suppression control 2 when the gain
switching is enabled.
VRF22B
When you set a value less than 0.1 Hz, the value will be the same as [Pr. PB53].
Vibration
suppression This parameter will be enabled only when the following conditions are fulfilled.
control 2 -
Resonance
frequency
after gain
switching
Switching during driving may cause a shock. Be sure to switch them after the servo
motor or linear servo motor stops.
Setting range: 0.0 to 300.0
PB58 Set a damping of the vibration frequency for vibration suppression control 2 when
the gain switching is enabled.
VRF23B
This parameter will be enabled only when the following conditions are fulfilled.
Vibration
suppression
control 2 -
Vibration
frequency
damping after
gain
switching
Switching during driving may cause a shock. Be sure to switch them after the servo
motor or linear servo motor stops.
Setting range: 0.00 to 0.30
PB59 Set a damping of the resonance frequency for vibration suppression control 2 when
the gain switching is enabled.
VRF24B
This parameter will be enabled only when the following conditions are fulfilled.
Vibration
suppression
control 2 -
Resonance
frequency
damping after
gain
switching
Switching during driving may cause a shock. Be sure to switch them after the servo
motor or linear servo motor stops.
Setting range: 0.00 to 0.30
"Gain adjustment mode selection" in [Pr. PA08] is "Manual mode (_ _ _ 3)".
"Vibration suppression mode selection" in [Pr. PA24] is "3 inertia mode (_ _ _ 1)".
"Vibration suppression control 2 tuning mode selection" in [Pr. PB02] is "Manual
setting (_ _ 2 _)".
"Gain switching selection" in [Pr. PB26] is "Input device (gain switching (CDP)) (_
_ _ 1)".
"Gain adjustment mode selection" in [Pr. PA08] is "Manual mode (_ _ _ 3)".
"Vibration suppression mode selection" in [Pr. PA24] is "3 inertia mode (_ _ _ 1)".
"Vibration suppression control 2 tuning mode selection" in [Pr. PB02] is "Manual
setting (_ _ 2 _)".
"Gain switching selection" in [Pr. PB26] is "Input device (gain switching (CDP)) (_
_ _ 1)".
"Gain adjustment mode selection" in [Pr. PA08] is "Manual mode (_ _ _ 3)".
"Vibration suppression mode selection" in [Pr. PA24] is "3 inertia mode (_ _ _ 1)".
"Vibration suppression control 2 tuning mode selection" in [Pr. PB02] is "Manual
setting (_ _ 2 _)".
"Gain switching selection" in [Pr. PB26] is "Input device (gain switching (CDP)) (_
_ _ 1)".
"Gain adjustment mode selection" in [Pr. PA08] is "Manual mode (_ _ _ 3)".
"Vibration suppression mode selection" in [Pr. PA24] is "3 inertia mode (_ _ _ 1)".
"Vibration suppression control 2 tuning mode selection" in [Pr. PB02] is "Manual
setting (_ _ 2 _)".
"Gain switching selection" in [Pr. PB26] is "Input device (gain switching (CDP)) (_
_ _ 1)".
Function
5 - 36
Control
Initial
mode
value
[unit]
P S T
0.0
[Hz]
0.0
[Hz]
0.00
0.00