Explanation Of Ic; Terminal Description - Clarion PN-3124N-A Service Manual

EXPLANATION OF IC

051-3516-90 S-1132B33-U5T1G
Vout 1
Ground 2
No Connectin 3
051-3517-90 impossible of exchange (LT3481EMSE#TRPBF)
TOP V I E W
B D 1
B O O S T 2
S W 3
V I N 4
R U N / S S 5

Terminal Description

BD (Pin 1):
This pin connects to the anode of the boost Schottky diode.
BOOST (Pin 2):
This pin is used to provide a drive voltage, higher than the input
voltage, to the internal bipolar NPN power switch.
SW (Pin 3):
The SW pin is the output of the internal power switch. Connect this
pin to the inductor, catch diode and boost capacitor.
VIN (Pin 4):
The VIN pin supplies current to the LT3481's internal regulator and
to the internal power switch. This pin must be locally bypassed.
RUN/SS (Pin 5):
The RUN/SS pin is used to put the LT3481 in shutdown mode. Tie
to ground to shut down the LT3481. Tie to 2.3V or more for nor-
mal operation. If the shutdown feature is not used, tie this pin to
the VIN pin.
PG (Pin 6):
The PG pin is the open collector output of an internal comparator.
PG remains low until the FB pin is within 10% of the final regula-
tion voltage. PG output is valid when VIN is above 3.5V and RUN/
SS is high.
BIAS (Pin 7):
The BIAS pin supplies the current to the LT3481's internal regula-
tor. Tie this pin to the lowest available voltage source above 3V
(typically VOUT). This architecture increases efficiency especially
when the input voltage is much higher than the output.
FB (Pin 8):
The LT3481 regulates the FB pin to 1.265V. Connect the feedback
resistor divider tap to this pin.
VC (Pin 9):
The VC pin is the output of the internal error amplifier. The volt-
age on this pin controls the peak switch current. Tie an RC net-
work from this pin to ground to compensate the control loop.
RT (Pin 10):
Oscillator Resistor Input. Connecting a resistor to ground from this
pin sets the switching frequency.
Exposed Pad (Pin 11):
Ground. The Exposed Pad must be soldered to PCB.
Positive Voltage Regurator 3.3V
5 Vin
Ground
4 Control (H= On)
Step-Down Switching Regulator
10 RT
9 V C
11
8 F B
7 B I A S
6 P G
051-3518-90 NJM2846DL3-33-TE1
3
051-3519-90 NJU7771F05-TE2
Control (H= On)
051-9425-80 S-24CS64A0I-J8T1G
A 0
A 1
A 2
G N D
Terminal Description
pin 1: A 0
pin 2: A 1
pin 3: A 2
pin 4: GND
pin 5: S DA
pin 6: S CK
pin 7: Write Protect
pin 8: VCC
052-0320-00 M30876FJBGP
[ Note ] The program is not written in this IC. Therefore, you need to
write a program in this IC with the part exchange.
Terminal Description
pin 1: NU
pin 2: Speed Pulse
pin 3: IMMOBI TX
pin 4: IMMOBI RX
pin 5: BU DET
pin 6: GND
pin 7: CN VSS
pin 8: ILL ON
pin 9: SYS ON
pin 10: RESET
pin 11: X out
pin 12: VSS
pin 13: X in
pin 14: VDD
pin 15: NMI
- 3 -
Positive Voltage Regurator 3.3V
5 N.C
4 Power Outut
3 Ground
2 VCC
1 Control in, H = ON.
Positive Voltage Regurator 5.0V
1 5 Vin
Ground 2
N.C. 3 4 Vout
1 8 VCC
2 7 W P
3 6 SCL
4 5 SDA
: IN : Address input.
: IN : Address input.
: IN : Address input.
: - : Ground.
:I/O: Serial data input/output.
: IN : Serial clock pulse input.
: IN : Write protect signal input.
H = protect ON.
: - : Positive voltage supply.
System Contoller
: IN : Not in use.
: IN : Speed pulse input.
: O : Serial data output for IMMOBI.
: IN : Serial data input for IMMOBI.
: IN : Backup detection signal input.
: - : Ground.
: IN : Connect to VSS via a resistor.
: IN : Illumination ON signal input.
: O : System ON signal output.
: IN : Reset signal input.
: O : Crystal connection.
: - : Negative voltage supply.
: IN : Crystal connection.
: - : Positive voltage supply.
: IN : Nonmaskable interrupt. Connect to VDD
via a resistor.
EEP-ROM
PN-3124N