Panasonic KX-FP215 Service Manual page 97

Code
571 ITS auto redial time set
572 ITS auto redial line disconnection time set
573 Remote turn-on ring number
574 Dial tone detect check
580 TAM continuous tone detection
590 FAX auto redial time set
591 FAX auto redial line disconnection time set
592 CNG transmit select
593 Time between CED and 300 bps
594 Overseas DIS detection
595 Receive error limit value
596 Transmit level set
Receiving Sensitivity
*1
598
599 ECM Frame size
625 Setting printing density
710 Memory clear except History data
717 Transmit speed select
718 Receive speed select
722 Redial tone detect
732 Auto disconnect
745 Power on film feed
763 CNG detect time for friendly reception
773
DIS-DCS interval
774 T4 timer
784 Voice prompt
815 Sensor & VOX test
841 Digital SP-Phone RX & TX check
852 Print test pattern
853 Top margin
874 DTMF ON time
875 DTMF OFF time
880 History list
881 Journal 2
882 Journal 3
991 Remote Setup list
994 Remote Journal list
995 Remote Journal 2 list
996 Remote Journal 3 list
998 Remote History list
999 Remote Service list
OK means "can set".
NG means "can not set".
Note:
*1
• : Power is OFF/ON after changing this set value.
• Refer to Service Function Table (P.63) for descriptions of the individual codes.
Example:
If you want to set value in the "004 Print confirmation report", press the dial key number 1,2 or 3 corresponding to the Set Value
you want to select. (1:ERROR / 2:ON / 3:OFF)
Function
00~99
001~999 sec
01~99
1: ON / 2: OFF
1: ON / 2: OFF
00~99
001~999 sec
1:OFF / 2:ALL / 3:AUTO
1: 75 ms / 2: 500 ms / 3: 1 sec
1: 1st / 2: 2nd
1: 5% / 2: 10% / 3: 15% / 4: 20%
-15~00 dbm
-20~-48 dbm
1: 256 byte / 2: 64 byte
1: Default / 2: Lighter / 3: Darker
1: 14400 / 2: 12000 / 3: 9600 / 4: 7200 /
5: 4800 / 6: 2400 bps
1: 14400 / 2: 12000 / 3: 9600 / 4: 7200 /
5: 4800 / 6: 2400 bps
1: ON / 2: OFF
1: 2 sec / 2: 4 sec / 3: OFF
1: ON / 2: OFF
1: 10 sec / 2: 20 sec / 3: 30 sec
1: 500 msec / 2: 200 msec
00~99 x 100 msec
1~9 mm
06~20 × 10 msec
06~20 × 10 msec
1:Start
1:Start
1:Start
1:Start
1:Start
1:Start
1:Start
1:Start
1:Start
Set Value
---------
---------
---------
---------
---------
97
KX-FP215
Default Remote Set-
ting
00 OK
065 sec OK
10 OK
OFF OK
ON OK
01 OK
065 sec OK
ALL OK
75 ms OK
1st OK
10% OK
-10 dbm OK
-42 dbm OK
256 byte OK
Default OK
--------- NG
14400 bps OK
14400 bps OK
OFF OK
2 sec OK
ON OK
30 sec OK
200 msec OK
00 msec OK
--------- NG
--------- NG
--------- NG
--------- NG
5 mm OK
10 × 10 msec
OK
10 × 10 msec
OK
--------- NG
--------- NG
--------- NG
--------- OK
--------- OK
--------- OK
--------- OK
--------- OK
--------- OK