Protecting The Environment - DeWalt DWV902L User Manual

English
Optional Accessories

WARNING: Since accessories, other than those offered by
D WALT, have not been tested with this product, use of
e
such accessories with this appliance could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
ACCESSORIES
DWV9340-XJ Filter
DWV9315-XJ Crush-proof hose
DWV9316-XJ Anti-static hose
DWV9401-XJ Paper bag
DWV9400-XJ Plastic liner
DWV9402-XJ Fleece bag
DWV9500-XJ Vac Rack
D WALT AirLock System
e
DWV9000 Twist-Lock connection
DWV9110 29–35 mm tapered
rubber adapter
DWV9120 35–38 mm stepped
rubber adapter
DWV9130 35 mm OD adapter
DWV9150 35 mm OD angle
adapter
Vac Rack DWV9500 Installation (Fig. K, L)
nOTE: The DWV902MT comes with DWV9500 vac rack
attachment already installed,
1. Remove the 4 carry handle screws using a T-25 star bit and
remove the carry handle.
2. Install the vac rack reusing the carry handle screws. Put
them back in their original holes and tighten.
3. Use the 2 screws 28 provided by placing them in the rear
holes of the vac rack. Push down and turn each screw to
break through the material and into the hidden screw boss
below. Tighten.

CAUTION: Do not exceed 9 kg (20 lb) in each 14 liter
storage unit, maximum 2 storage units per dust
extractor. Do not exceed 18 kg (40 lb) in a 28 liter storage
unit, 1 storage unit per dust extractor. Exceeding the
recommended height and/or weight could result in
an unstable dust extractor would could cause injury or
damage.
NOTICE: Do not remove dust extractor head from tank
with T-stack storage units attached. Doing so could result
in damage to the dust extractor filter.
Securing the Power Cord to the
Hose (Fig. A)
The power cord 2 can be secured to the suction hose
the D279058CL hose clip (available from your local D
supplier).
Consult your dealer for further information on the appropriate
accessories.
10
Troubleshooting
Problem Solution
Motor does
not run
WALT recommended
e
Suction
capacity
decreases
Vacuum
stops
running
Dust comes
out while
vacuuming
Automatic
filter
cleaning is
not working
Power tool
does not
turn on.

Protecting the Environment

be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
7 using
www.2helpU.com.
WALT
e
Check power cord, plugs and outlet.
Ensure the on/off /tool control switch is in the
ON position ( ).
Remove blockages in the suction nozzle,
suction tube, suction hose or filters.
Replace the paper or fleece bag.
Check for proper installation of the filters.
Clean or replace the filters.
Empty canister, refer to Empty Canister under
Operation.
Thermal overload has been tripped:
1. Turn the vacuum off and disconnect
vacuum cleaner from power source.
2. Empty the canister, if needed.
3. Allow the unit to cool.
4. Plug the power cord into an appropriate
outlet and turn on/off/tool control switch
to the ON position ( ) to test. If vacuum will
not restart contact your seller or check the
location of your nearest authorised D
repair agent in the D
contact your D WALT office at the address
e
indicated in this manual.
Check for proper installation of the filters.
Ensure filters are not damaged; replace if
necessary.
Ensure filter seals are in place and are secure.
Listen for the solenoid clicking to ensure the
filter cleaning mechanism is working.
Ensure the on/off/tool control switch is in the
ACTIVATION position
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
WALT
e
WALT catalogue or
e
.