DeWalt DWV902L User Manual page 9

nOTE: This appliance is suited for the commercial use, e.g.
in hotels, schools, hospitals, factories, shops, offices, rental
companies, and on construction sites.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Anti-Static Hose Option
The DWV902L, DWV902M and DWV902MT are each equipped
with an anti-static grounding system. An anti-static hose must
be purchased at extra cost from your authorised service center.
This hose (DWV9316-XJ) fits into the dust extractor system the
same way as the standard hose. To contact your seller or check
the location of your nearest authorised D
in the D WALT catalogue or contact your D
e
address indicated in this manual.
ASSEMBLY AND ADJUSTMENTS (FIG. A–C)

WARNING: To reduce the risk of injury, turn
appliance off and disconnect appliance from power
source before installing and removing accessories,
before adjusting or changing set-ups or when
making repairs. An accidental start-up can cause injury.

WARNING: The filters 9
vacuuming, except as described under Wet Pick Up
Applications under Operation. When vacuuming fine
dust, you may also use an additional paper bag or fleece
bag to make emptying the canister easier.

WARNING: Dust collection bags must be used for dust
Class M.
1. If optional paper or fleece bag
shown in figure B.
nOTE: Be careful not to tear the bag. Place bag securely
onto inlet 10 to provide a tight seal for maximum dust
collection performance.
2. Place the vacuum head 3
closing the canister latches
3. Insert end of hose 7 into twist-lock hose inlet
rotate counterclockwise to lock in place.
OPERATION
Instructions for Use (Fig. A, D)

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of injury, turn
appliance off and disconnect appliance from power
source before installing and removing accessories,
before adjusting or changing set-ups or when
making repairs. An accidental start-up can cause injury.
1. Plug the power cord into an appropriate outlet.
WALT repair agent
e
WALT office at the
e
must always be in place while
20 is to be used, install as
onto the canister and secure it by
.
4
10 and
2. Turn the on/off/tool control switch
position ( ).
3. Set the variable suction dial
This feature allows the user to control the vacuum's power,
suction and noise.
nOTE: This setting also controls the level of suction. This
is very useful in applications where the vacuum creates
unacceptable levels of drag to the work piece.
4. Follow the direction under Connecting to Power Tools to
connect to the power tool to be used.
Flow Alarm Adjustment (Fig. D)
Class M models only
Adjust the flow alarm adjustment control
hose (or tube) inside diameter size or accessory diameter
referring to the largest section. The chosen diameter of the
adjustment control must be equal or bigger as the largest
diameter of the used hose/tube/ accessories. The hose supplied
is 32 mm inside diameter. An acoustic alarm will sound if the
flow rate falls below 20 m/s. The system has a time delay to
reduce unintended alarms.
If the alarm sounds when there is no apparent blockage:
1. Ensure that the adjustment control is set to the correct
diameter.
2. If the flow rate adjustment is set below the maximum,
increase this level until sufficient flow through the hose
causes the alarm to stop.
3. If the alarm still continues to sound, remove hose and check
that it is clear. Remove and replace dust bag if full or blocked
and check filter condition and replace where necessary.
If the alarm continues to sound contact your local D
service agent.
Connecting to Power tools (Fig. A, D, E)

WARNING: Only use the outlet
in the instructions.
1. Plug the vacuum power cord into an appropriate outlet.
2. Plug the power tool into the outlet
nOTE: See Power connection data of power tool under
Technical Data for the power allowance of the tool to be
plugged into the outlet 13
3. Turn on/off/tool control switch
position . This allows the vacuum to be turned on and
off automatically by the power tool.
nOTE: The vacuum cleaner starts automatically within
0.5 seconds and continues to run for 15 seconds after the
power tool has been turned off.
4. To switch back to manual mode, turn the on/off/tool control
switch 15 to the ON position ( ). In manual mode the tool
and the vacuum are turned on and off independent of each
other.
5. Your D WALT construction dust extractor is fitted with the
e
D WALT AirLock connection system. The AirLock allows for
e
a fast, secure connection between the suction hose
power tool. The AirLock connector
D WALT compatable tools or through the use of an AirLock
e
English
to the ON
15
14 to the desired position.
to the correct
16
WALT
e
13 for purposes specified
13 .
.
to the ACTIVATION
15
and
7
23 connects directly to
7