Monessen Hearth AVFL42NTSC Installation & Operating Instructions Manual page 27

TOUCH SCREEN REMOTE CONTROL OPERATION
NOTE: there will a 10
second delay for the
flame adjustment when
the fireplace is turned
on.
1. When Set Temp. is
3° F or higher than
Room Temp., flame
height will be on High.
2. When Set Temp. is 2°
F higher than Room
Temp., flame height
will be on Medium.
3. When Set Temp. is 1°
F higher than Room
Temp., flame height
will be on Low.
4. When Set Temp. is equal to Room Temp., flame height
does not change (stays on low).
5. When Set Temp. is lower than Room Temp., the fire-
place will be shut off.
6. When Set Temp. is 1° F higher than Room Temp.,
again the flame height will be on Low.
To exit Smart Mode and shut off the fireplace;
a. Push and hold the THERMO buttons for 3 seconds,
or
b. Press the OFF button
or
c. Slide down on the arrow buttons.
To shut off the Smart Mode option and return to regular
thermostat mode, press and hold the THERMO button
and the ON/UP button at the same time for 3 seconds
again.
Light Brightness Control
Figure 32
The light brightness control function is used to adjust the
brightness of the light bulbs connected to the AC module
on the Signature Command
brightness levels defined: Off,
Low, Medium, High
1. Press the LIGHT button to en-
ter the light brightness control
mode. The LIGHT icon will
start flashing.
2. Press the On/up and OFF/
down buttons to increase/
decrease the light brightness
(Off-Low-Medium-High).
3. Press the light button again to
confirm the setting. The new
setting will be transmitted to
the receiver.
Monessen • AVFL42 Installation Instructions • 20305467 Rev. B • 02/17
Figure 31
FP2654
smart mode
System. There are four light
®
Figure 32
FP2657
Light bright control
4. After the signal is sent, the On/up and Off/down but-
tons become flame height controller again.
5. When the light button is flashing, slide up and down on
the arrow buttons will turn the light brightness to HIGH
Smart
or Off directly without pressing the light button again to
Mode
confirm.
Icon
AUX Control
The AUX control function is used to turn on or turn off
the auxiliary component connected to the AC
module of the Signature Command
Press the AUX button to turn on or turn off the
auxiliary.
1. When the auxiliary is turned on, the icon will
become solid text and the "ON" icon will ap-
pear below the "AUX" icon.
2. When the auxiliary is turned off, the icon will
become hollow text and the "ON" icon will
disappear.
NOTE: Some fireplaces use the AUX function to control
options within the fireplace. Refer to fireplace manual for
operation.
Setting up Blank Screen or Constant Display in Idle
Figure 33
There is an option
to set up how the
LCD displays and
functions when the
transmitter is
idle. There are two
choices:
1. A) Mode. When
the transmitter is
in idle, the icons
in the "touch
area" (timer,
t h e r m o s t a t ,
blower, light and
AUX) will disappear, as shown in the figure on the left.
When any of the touch buttons is pressed, those icons
will appear and are ready to operate (default).
2. B) Mode. The transmitter always displays all available
icons showing current status of timer,
blower, light and AUX as shown in the figure on the
right.
Press TIMER and THERMO buttons at the same time for
3 seconds to toggle between A) and B).
1. When the current setting is A), touch any place in the
touch area to bring up the icons then press TIMER but-
ton and THERMO button at the same time for 3 sec-
onds. The backlight will flash once to indicate that the
setting has changed to B).
AVFL Vent Free Fireplace
System.
®
in
Figure 33
FP2659
blank screen
FP2658
AUX
thermostat,
27