Monessen Hearth AVFL42NTSC Installation & Operating Instructions Manual page 26

AVFL Vent Free Fireplace
2. Press the OFF/down button
to decrease the flame height
and turn off the fireplace.
When the OFF/down button
is pressed for three times,
the flame icon changes form
High to Medium, to Low,
then to Off.
3. If the OFF button is held for
more than 3 seconds at any
flame height, the fireplace
will be turned off and the
flame icon disappears.
4. Sliding up and down on the
arrow buttons can also turn
on or turn off the fireplace.
5. If the fireplace is shut off us-
ing the above methods in 3
and 4, all the settings will be
remembered and will be resumed next time the fire-
place is turned on (Memory Off).
Timer Mode
Figure 29
Press the TIMER button to en-
ter timer mode. The fireplace
will stay on for a period of time
as specified by the timer and
then be shut off by the transmit-
ter when the timer counts down
to zero.
1. When the TIMER button is
pressed, the Set Time ap-
pears in the frame of the but-
ton and flashes.
2. Use ON/up and OFF/down
to increase or decrease
the Set Time in 15 min. in-
crements, between 0:00 to
6:00. Sliding up and down
on the arrow buttons will in-
crease or decrease the Set Time in 1 hour increments.
3. Push the TIMER button again to confirm the Set Time,
the transmitter sends an ON signal to turn on the fire-
place.
4. The flashing stops and the ON/up and OFF/down but-
tons become flame height controller again. The flame
height will then stay as set up by the ON/up and OFF/
down buttons.
5. The TIMER button can be used when the transmitter
is in Manual Mode or in Thermostat Mode. In both
modes, the fireplace will be shut down completely
when the timer counts down to zero.
6. To exit Timer Mode:
Monessen • AVFL42 Installation Instructions • 20305467 Rev. B • 02/17
26
TOUCH SCREEN REMOTE CONTROL OPERATION
Figure 28
FP2651
Manual mode
Figure 29
FP2652
Timer mode
a. Push and hold the TIMER button for 3 seconds or
b. Use the OFF/down buttons to decrease the Set
Time to zero or
c. Slide down on the arrow buttons to exit TIMER
mode and shut off the fireplace.
Thermostat Mode
Figure 30
Press the THERMO button to
set the transmitter in thermo-
stat mode. The transmitter will
automatically turn on the fire-
place when the room tempera-
ture is below the set tempera-
ture and turn off the appliance
when the room temperature
is above the set temperature
within one degree.
1. When the THERMO button
is pressed, the Set tempera-
ture appears in the frame of
the button and flashes.
2. Use ON/up and OFF/down
to increase or decrease the
Set temperature in 1 degree
increments, between 45 degrees and 90 degrees.
Slide up and down on the arrow buttons will increase
or decrease the Set Temperature in 10 degrees incre-
ments.
3. Press the THERMO button again to confirm the Set
Temperature. The transmitter will send out an On
signal or an Off signal depending on the relationship
between the Set temperature and the Room tempera-
ture.
4. The flashing stops and the ON/up and OFF/down but-
tons become flame height controller again. The flame
height will then stay as set up by the ON/up and OFF/
down buttons.
5. To exit Thermostat Mode:
a. Push and hold the THERMO buttons for 3 seconds
or
b. Slide down on the arrow buttons to exit Thermostat
mode and shut off the fireplace.
Smart Mode Option for Thermostat Mode
Figure 31
Press and hold the THERMO button and the ON/UP but-
ton at the same time for 3 seconds to toggle between
Smart Mode and the regular Thermostat Mode. The icon
"Smart Mode" will appear under the Set Temperature.
The transmitter will automatically adjust the flame height
according to the difference between the Set temperature
and the Room temperature. There is no manual flame
height adjustment.
Figure 30
FP2653
thermo mode