IDEAL VOGUE COMBI C26 User Manual
Gen2
Hide thumbs
Also See for VOGUE COMBI C26:
- Installation and servicing (77 pages) ,
- User manual (21 pages) ,
- User manual (4 pages)
Table of Contents
Advertisement
USER GUIDE
VOGUE COMBI
C26 C32 C40
January 2017
UIN 216173 A02
When replacing any part on this appliance, use only spare parts that you can be
assured conform to the safety and performance specification that we require.
Do not use reconditioned or copy parts that have not been clearly authorised by Ideal Boilers.
GEN2
Advertisement
Table of Contents
Related Manuals for IDEAL VOGUE COMBI C26
Summary of Contents for IDEAL VOGUE COMBI C26
- Page 1 When replacing any part on this appliance, use only spare parts that you can be assured conform to the safety and performance specification that we require. Do not use reconditioned or copy parts that have not been clearly authorised by Ideal Boilers.
-
Page 3: Natural Gas Only
G.C. Appliance No. 47-349-40 Ideal Boilers is a member of the Benchmark scheme and fully supports the aims of the programme. Benchmark has been introduced to improve the standards of installation and commissioning of central heating systems in the UK and to encourage the regular servicing of all central heating systems to ensure safety and efficiency. - Page 4 FOR ANY QUERIES PLEASE RING THE IDEAL CONSUMER HELPLINE : 01482 498660 NOTE. BOILER RESTART PROCEDURE - To restart the boiler, press “RESTART” hot key located below the colour screen. The appliance will now repeat the ignition sequence if a heat demand is present.
-
Page 5: Important Notes
IMPORTANT NOTES • This appliance must not be operated without the casing correctly fitted and forming an adequate seal. • If the boiler is installed in a compartment then the compartment MUST NOT be used for storage purposes. • If it is known or suspected that a fault exists on the boiler then it MUST NOT BE USED until the fault has been corrected by a Gas Safe Registered Engineer or in IE a Registered Gas Installer (RGII). -
Page 6: Boiler Controls
BOILER CONTROLS Legend Domestic Hot Water / Preheat Status Hot Keys G. Pressure Gauge Central Heating Status Central Heating Temperature Control Hot Key Identification Text Burner On indication Domestic Hot Water Temperature Control / Off Switch READY 60°C TIMER OR ROOM THERMOSTAT OFF MENU boiler... -
Page 7: Ignition Lockout
TO LIGHT THE BOILER - (REFER TO BOILER CONTROLS) If a programmer is fitted refer to separate instructions for the If the boiler has not lit, after 5 ignition attempts, the following programmer before continuing. screen will be displayed. Switch ON electricity to the boiler and check that all IGNITION LOCKOUT external controls, e.g. -
Page 8: Operation
CONTROL OF WATER TEMPERATURE OPERATION Central Heating and Domestic Hot Water required. Domestic Hot Water The boiler will fire and supply heat to the radiators but will give The DHW temperature is limited by the boiler controls to 65 maximum at low draw-off rate, adjustable via the Domestic Hot priority to Domestic Hot Water on demand. -
Page 9: Weather Compensation
WEATHER COMPENSATION BOILER OVERHEAT PROTECTION When the Weather Compensation option is fitted to the The boiler controls will shut down the boiler in the event of system then the Central Heating Temperature Control knob overheating. Should this occur, the following display will appear; (E) becomes a method of controlling room temperature. -
Page 10: Loss Of System Water Pressure
fill With boiler o & system cold fill system to between 1.0 & 1.5 bar (Press PICTURE to see how) Bleed radiators then refill If fault persists contact Ideal (01482 498660) If pressure loss re-occurs contact installer EXIT PICTURE EXIT... - Page 11 To Top up the system :- Ensure both A & B handles (blue) are in closed position Turn the Domestic Hot Water (DHW) Inlet A blue handle (as shown). to the horizontal position. Remove the plug and cap and retain. Ensuring no leaks are seen, gradually turn the filling loop Connect the filling loop to the Domestic Hot Water (DHW) handle (blue) B to the horizontal position.
-
Page 12: Condensate Drain
CONDENSATE DRAIN To unblock a frozen condensate pipe; This appliance is fitted with a siphonic condensate trap 1. Follow the routing of the plastic pipe from its exit point on system that reduces the risk of the appliance condensate the appliance, through its route to its termination point. from freezing. -
Page 13: Escape Of Gas
ESCAPE OF GAS MAINTENANCE Should a gas leak or fault be suspected contact the National The appliance should be serviced at least once a year by Gas Emergency Service without delay. Tel. 0800 111 999 a Gas Safe Registered Engineer or in IE a Registered Gas Installer (RGII). -
Page 14: Points For The Boiler User
POINTS FOR THE BOILER USER Note. In line with our current warranty policy we would ask that you check through the following guide to identify any problems external to the boiler prior to requesting a service engineer’s visit. Should the problem be found to be other than with the appliance we reserve the right to levy a charge for the visit, or for any pre-arranged visit where access is not gained by the engineer. -
Page 15: Fault Finding
FAULT FINDING If a fault occurs then a fault description and suggested potential corrective actions will be displayed. In addition the following information may be useful. Rotate the Central Heating temperature control knob (E) clockwise. Hot water works OK but no Ensure that the timer and Room Stat are switched on. -
Page 16: Display Functions In Normal Operation
DISPLAY FUNCTIONS IN NORMAL OPERATION Indicates that the Boiler is Switched Off. Indicates that all taps Indicates that the timer or Move DHW Temp Control knob clockwise to switch the boiler on. and showers are off. room stat is switched off READY READY PREHEAT OFF... - Page 17 To switch pre-heat Off, see page 20 To reset, see page 22 - Reset Service Time READY READY PREHEAT 60°C ACTIVE TIMER OR ROOM SWITCH OFF TIMER OR ROOM THERMOSTAT OFF TEMPERATURE AT 60 THERMOSTAT OFF SERVICE DUE Ideal Boilers 01482 498660 MENU MENU...
-
Page 18: Change Settings
CHANGE SETTINGS To change the Hot Water temperature rotate the To switch the heating on, rotate the Central Heating Domestic Hot Water knob (F). This screen will be shown; knob (E) clockwise. This screen will be shown; SELECT HOT WATER TEMPERATURE SELECT MAXIMUM RADIATOR TEMPERATURE EXIT EXIT... - Page 19 To disable Domestic Hot Water and Central Heating (frost To change the room temperature set point (only if outside protection still active) rotate the Domestic Hot Water knob (F) sensor connected) rotate the Central Heating knob (E). fully anti-clockwise. This screen will be shown; This screen will be shown;...
-
Page 20: Menu Operation
MENU OPERATION Pre-heat If pre-heat is switched on then the boiler will periodically fire the burner thereby reducing the time taken to provide hot water. If pre-heat is switched off the response time will be increased although gas consumption will also be reduced. To switch preheat off press ‘OFF’... - Page 21 Efficiency Level Press select and a screen similar to the following To view the efficiency level of the boiler press MENU will be displayed; and the following screen will be displayed; EFFICIENCY LEVEL MENU SHOW EFFICIENCY LEVEL HOT WATER PREHEAT ON / OFF SERVICE COMPANY NAME EXIT SELECT...
- Page 22 Reset Service Time If the boiler has not been serviced within the last 12 months, a Press SELECT and the following screen is displayed; message will be displayed indicating this. To reset the timing of this message, following a boiler service press MENU and the following screen will be displayed;...
- Page 24 Ideal Boilers Ltd., pursues a policy of continuing improvement in the design and performance of its products. The right is therefore reserved to vary specification without notice. Ideal Boilers Ltd., P.O. Box 103, National Ave, Kingston Upon Hull, HU5 4JN.