Texas Instruments 880 User Manual page 8

Section Title Page Section Title Page
5.4.1 Seven-Bit Environment
...............
5-7
7.2.2 Serial Connector Pin Listing
7-3
5.4.2 Eight-Bit Environment ................. 5-9
7.3
Parallel Interface ........................ 7-3
7.3.1 Parallel Connector Pin Listing
.......
7-3
6 Raster Graphics
7.3.2 Parallel Data Timing
...................
7-6
7.3.3 Paper-Out and Mechanism
6.1 Vertical Raster Graphics
..............
6-1 Faults
.
...................................
7-6
6.2 Horizontal Raster Graphics ........... ' 6-4
7.3.4 Sequence to Initialize the
6.2.1 Horizontal Raster Data Formatl Printer
...................................
7-6
Single-Density Plot Mode
...........
6-4
6.2.2
Horizontal Raster Data Formatl Appendixes
Double-Density Plot Mode
.........
6-5
A TI Business Systems
7
Communication Interfaces
B Maintenance
C Control and Character Codes
7.1 Data Input Buffer ....................... 7-1
0 Power Requirements and Grounding
7.2
Serial Interface
..........................
7-3 E Options and Accessories
7.2.1 Data Structure
..........................
7-3 F Specifications
List of Tables
Table No.
Title Page
Table No. Title Page
3-1 Configuration Codes .................. 3-12
5-11 Printer Status Escape
3-2 Characters Per Line .................... 3-13 Sequences ...... ..... ... . .. ...... .. .... 5-6
3-3 Default Form Lengths ................. 3-17 5-12 Escape Sequences For Character
3-4 Print Features Switch Defaults ...... 3-18 Set Designation ...... .. ...... ........ 5-10
3-5 Default Configuration Codes ........ 3-18 5-13 Escape Sequences For Character
3-6
Default Character Set
Set Invocation ......................... 5-11
Designations ........................... 3-18 5-14 Special Character Selection
Commands ............................. 5-11
4-1 Error Codes
..............................
4-3 5-15 Font ROM Positions ................... 5-11
4-2 Problem Analysis Procedures
.......
4-6
6-1 Vertical Raster Graphics Eight-bit
5-1 ASCII Chart with Decimal and Data-to-Dot Map ..................... 6-1
Hexadecimal Codes
..................
5-1
6-2 Vertical Raster Graphics Seven-Bit
5-2 Control Character Operations
.......
5-2 Data-to-Dot Map ...... ............... 6-1
5-3
Form Length Escape Sequences .... 5-4
6-3 Escape Sequences for Vertical
5-4 Margins and Defaults .................. 5-4
Raster Graphics ....................... 6-2
5-5 Margin Control Escape
Sequences
.............................
5-4
7-1 Buffer Size and READY IBUSY
5-6 Horizontal Tab Escape Points .. ................................. 7-1
Sequences
.............................
5-5 7-2 READY IBUSY Signals ............... 7-2
5-7 Vertical Tab Escape Sequences
.....
5-5 7-3 Serial Interface Signals ............... 7-4
5-8 Horizontal Pitch Escape 7-4 Parallel Interface Signals ............. 7-5
Sequences
.............................
5-6
5-9 Characters Per Line
....................
5-6 C-1 ASCII Code Characters ............... C-1
5-10 Vertical Pitch Escape C-2 National Language Characters that
Sequences
.............................
5-6 Differ from US ASCII
Characters ............................. C-2
vi