Table of Contents
Advertisement
Owners &
Classic™ FP90 Wood Fireplace
Installation Manual
US Edition
MODEL: FP90
www.regency-fire.com
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
10.06.16
919-541c
Advertisement
Table of Contents
Related Manuals for Regency FP90
Summary of Contents for Regency FP90
- Page 1 Owners & Classic™ FP90 Wood Fireplace Installation Manual US Edition MODEL: FP90 www.regency-fire.com Tested by: Installer: Please complete the details on the back cover and leave this manual with the homeowner. Homeowner: Please keep these instructions for future reference. FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4 10.06.16...
- Page 2 The following statements are required by the Environmental Protection Agency: “This manual describes the installation and operation of the Regency FP90/R90/EX90 wood heater. This heater meets the 2015 U.S. Environmental Protection Agency’s crib wood emission limits for wood heaters. Under specific test conditions this heater has been shown to deliver heat at rates ranging from 11,700 BTU/hr.
- Page 3 FP90 Wood Fireplace |...
-
Page 4: Table Of Contents
Air-Cooled Chimney Adaptor-Metal Fab ......20 Parts List- Firebox & Body ...........39 Installing The Outside Air Kit ........20 Parts List- Baffles, Door, Options ........40 Gravity Air Feed Kit Option ..........21 Warranty ..............42 Finishing The Regency Fp90 ........22 Completing The Facing ..........22 | FP90 Wood Fireplace... -
Page 5: Safety Label For Fp90
This is a copy of the label that accompanies each Regency Fireplace. NOTE: Regency units are constantly being improved. Check the label It is located inside the lower louver opening on the left side. We have on the unit and if there is a difference, the label on the unit is the correct printed a copy of the contents here for your review. -
Page 6: Product Details
Options Ashdrawer R90 / EX90 Fan R90 / EX90 Surround Black EX90 Louver Flush Black R90 Wood Screen R90 / EX90 Gravity Vent Kit R90 Air Cool Pipe Adaptor R90 / EX90 1" Unit Base Standoffs | FP90 Wood Fireplace... -
Page 7: Read Before You Install
16) DO NOT use a fireplace insert or any other these get very hot and expand. read and understand these instructions before product not specified by Regency for use beginning your installation. 7) DO NOT use charcoal or coal under any with this fireplace. -
Page 8: Dimensions And Specifications
DIMENSIONS AND SPECIFICATIONS The Regency is a wood burning fireplace This fireplace system is designed for installation The FP90 main unit consists of the following: featuring a self-contained heat-circulating in accordance with the National Fire Protection system and cast-iron doors with large viewing... -
Page 9: Clearances And Height Requirements
CLEARANCES AND HEIGHT REQUIREMENTS WARNING: If insulation is used, do not place The FP90 may be placed on or near construction the unit against it. Insulation or vapor barriers, materials. The combustion air kit, fire stop spacer if used, must be secured to assure insulation... -
Page 10: Installation Of Nailing Strips
Nailing Strips. The Nailing Strips can also be moved forward and back by adjusting Building Structures Cannot the screws that mount them to the fireplace. Encroach on Chase 10 | FP90 Wood Fireplace... -
Page 11: Framing Details
FRAMING DETAILS Note: The “Z” type safety strip is not supplied by Regency and must be Note: Ducting is tested at 1 in. (25mm) clearance to framing. fabricated locally. Stud 2 x 6 Wall with a FINISHING MATERIAL 2 x 4 Header... -
Page 12: Chimney System Considerations
This unit requires the chase to be ventilated with one 30 sq. inch vent. Refer to Installation Measurements section. Regency’s FP90 Fireplace is to be installed with one of the following Chimney Systems only. A chase is a vertical box-like structure constructed Chimney systems only 8"... -
Page 13: Installation Measurements / Framing Details
INSTALLATION MEASUREMENTS / FRAMING DETAILS FP90 Wood Fireplace |... -
Page 14: Assembly Steps
14 | FP90 Wood Fireplace... -
Page 15: Offset Chimney Installation
Ensure the heater is in- stalled in areas that are not too close to neighbors or in valleys that would cause unhealthy air quality or nuisance conditions. FP90 Wood Fireplace |... - Page 16 13.92 15.08 16.24 17.4 20.88 5000-6000 14.40 15.60 16.80 18.0 21.60 6000-7000 14.88 16.12 17.36 18.6 22.32 7000-8000 15.36 16.64 17.92 19.2 23.04 8000-9000 15.84 17.16 18.48 19.8 23.76 9000-10000 16.32 17.68 19.04 20.4 24.48 16 | FP90 Wood Fireplace...
-
Page 17: Air-Cooled Chimney Adaptors
FOR MAJESTIC SK8 SERIES CHIMNEY TO COLLAR (3 SCREWS). Majestic SK8 Chimney System OUTER CHIMNEY ADAPTER FOR SECURITY FTF8 SERIES CHIMNEY INNER FLUE ADAPTER FOR SECURITY FTF8 SERIES CHIMNEY Security FTF8 Chimney System 918-439a 09/19/05 PAGE 1 OF 3 FP90 Wood Fireplace |... - Page 18 (Screws provided). FIRST INNER FLUE SECTION (FITS INSIDE (FITS INSIDE (FITS INSIDE USE 3 SCREWS ADAPTER COLLAR) ADAPTER COLLAR) FLUE COLLAR 18 | FP90 Wood Fireplace Majestic SK8 Chimney System 918-439a PAGE 2 OF 3 09/19/05...
- Page 19 The chimney sections may be damaged if they have to be removed and can not be used again if the locking tabs do not hold the connections tightly. 918-439a PAGE 3 OF 3 09/19/05 FP90 Wood Fireplace |...
-
Page 20: Air-Cooled Chimney Adaptor-Metal Fab
Side Connection Exterior Unit Wall Outside Metal Insulated Metal Vent 6 Duct Outside Air Inlet must be 6 ft. (152mm) below the chimney termination point Metal Fab attached to the unit 20 | FP90 Wood Fireplace 919-591 08.10.15... -
Page 21: Gravity Air Feed Kit Option
GRAVITY AIR FEED KIT OPTION The Gravity Air Feed Kit is designed to extend the heat output vent above the FP90 to the front or the side. The upper louver opening is blocked off and flex vent is connected to the vent holes in the top of the unit and run to discharge vent grilles. -
Page 22: Finishing The Regency Fp90
Use the chase vent supplied with 3/4" (19mm) thick to prepared surface area. the FP90 unit only or any equivalent one with Do not spread more than a workable area so the same or less restriction of air flow. -
Page 23: Masonry Retainer Kit Option
2) Unscrew the top stand-off and move the ceramic blanket forward so it will be tight against the mesh to make a seal. 2" (51mm) x 4" (102mm) Metal Filler Strips Metal Filler Strips MIDDLE LEFT RIGHT SIDE SIDE FP90 Wood Fireplace |... -
Page 24: Finishing Details
Face Header. Example 1: Face of Fireplace Flush with Wall Framing. Stone, Tile or Brick Mortar Heavy Expanded Metal Non-Combustible Material Top View Example 2: Face of Fireplace Flush with Non-Combustible. Top View 24 | FP90 Wood Fireplace... -
Page 25: Masonry Liner / Bricks
The air tube will be difficult to snap into place because it has to be a snug fit in order to prevent it from falling out when a fire is burning. Side Panel Top Panel Insulation Brick Bottom Fermiculite FP90 Wood Fireplace |... -
Page 26: Ash Drawer Kit Option
6) Slide the ash drawer into the ash drawer shelf. 7) Place the lid and the ash plug tool on the fan trasfer plate for storage. 26 | FP90 Wood Fireplace... -
Page 27: Fan Installation
See Diagram 3. 9) Reinstall the thumb screw. Diagram 3 GREEN GROUND Low Speed Red Wire not connected. THERMODISC GREY GREY BROWN BLUE GROUND GREEN SWITCH CONTROL BOX Diagram 2 POWER CORD 918-437 11.10.14 FP90 Wood Fireplace |... -
Page 28: Masonry Cover Plate Installation
FLANGES ARE ON THE INSIDE OF THE OPENING. SLOTTED HOLES ON RIGHT SIDE ONLY 43.000" (1092mm) NOTE: ONCE THE TEMPLATE IS MOUNTED CHECK TO MAKE SURE THE SIDES ARE PLUMB AND 43" (1092mm) IN WIDTH 28 | FP90 Wood Fireplace... - Page 29 TO PREVENT MASONRY FACING MATERIAL FROM HITTING THE TOP STIFFENER LOCATED ON THE BACK OF THE SURROUND WHICH IS HIGHER THAN THIS EDGE. INSTALL THE SURROUND TEMPLATE ONTO THE UNIT WITH THE SAME MOUNTING SCREWS AS THE SURROUND. FP90 Wood Fireplace |...
-
Page 30: Finishing Trim Kit Installation
fl ush with the face of the unit and allow the trim to be installed correctly (refer to Diagram 1). Front Trim Side Side Trim Trim Unit With Finished Trim Diagram Assembly De tails 918-442a 10/10/06 PAGE 1 OF 2 30 | FP90 Wood Fireplace... - Page 31 8) It is recommended that the joints of the sheathing run horizontal from the top corners of the unit rather than vertical. This will reduce the heat exposure to the joints and reduce the chance of the fi nish from cracking. PAGE 2 OF 2 918-442a 10/10/06 FP90 Wood Fireplace |...
-
Page 32: Fireplace Screen Installation
fi rebox fl anges. 2) Fasten the handles to the screen using the fasteners provided. Front View Side View 3) Install fi rescreen. Side View 32 | FP90 Wood Fireplace 918-444 01/12/06... -
Page 33: Regency Louver Installation
NOTE: Take care not to scratch the paint on the front of the fi replace when installing the top louver. Bottom Louver Frame Rotation Pin Tab (x2) Top Louver Mounting Tab (x2) Bottom Louver Rotation Pin Tab (x2) Diagram 2 Diagram 1 Bottom Louver Mounting Sequence 918-433 08/23/05 FP90 Wood Fireplace |... -
Page 34: Excalibur Faceplate Installation
Optional: 4) Install the optional masonry cover plate to the facing guides with four (4) screws (¼-20 x ½”). 43” (1092mm) 918-434 11/12/09 34 | FP90 Wood Fireplace... -
Page 35: Excalibur Accent Kit Installation
Place the emblem over the emblem design on the sur- round. Insert the studs through the holes. To secure them fi rst put on the split lock washer and then the nut and tighten. 918-438 08/23/05 FP90 Wood Fireplace |... -
Page 36: Seasoned Wood
Two dry pieces banged together sound hollow; wet pieces sound solid and dull. • Dry wood weighs much less than wet wood. • Split a piece of wood. If the exposed surface feels damp, the wood is too wet to burn. 36 | FP90 Wood Fireplace... -
Page 37: Operating Instructions
If creosote has accumulated it shall level. be removed to reduce the risk of a chimney fire. FP90 Wood Fireplace |... -
Page 38: Plated Finishes
34" (864mm) long for each side. brush. A proper high temperature gasket adhesive is Allow the stove to cool before removing or required. Contact your dealer for the Regency e. Replace chimney cap. replacing glass. Remove the door from the Gasket Repair Kit. -
Page 39: Parts List- Firebox & Body
Border Frame - Bottom Grille Ash Drawer Louver Support Frame - Bottom Grille Ash Drawer Lid 942-110 Ash Plug 820-375 Ash Hole Cover Plate Retainer Plate 9) 948-326 Intake Pipe 6" 948-327 Intake Pipe Insulation 948-416 6" Outside Air Kit FP90 Wood Fireplace |... -
Page 40: Parts List- Baffles, Door, Options
001-551 Door Handle Assembly Complete - Right 936-243 Tape 7/8 Window Adhesive 001-137 Steel Handle - Left Door 936-299 Tape 3/16 X 3/8in. 001-138 Steel Handle - Right Door 001-147F Anchor Bracket - Left Handle 40 | FP90 Wood Fireplace... - Page 41 FP90 Wood Fireplace |...
-
Page 42: Warranty
At all times FPI reserves the right to inspect reported complaints on location in the field claimed to be defective prior to processing or authorizing of any claim. Failure to allow this upon request will void the warranty. Revision Date: September 2016 Regency Wood Products Warranty 42 | FP90 Wood Fireplace... - Page 43 Freight damages for products or parts are not covered under the terms of the warranty. Products made or provided by other manufacturers and used in conjunction with the FPI appliance without prior authorization from FPI may void this warranty. Revision Date: September 2016 Regency Wood Products Warranty FP90 Wood Fireplace |...
- Page 44 Product Registration and Customer Support: Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and marketing of hearth products. To provide the best support for your product, we request that you complete a product registration form at http://www.regency-fire.com/Customer-Care/Warranty-Registration.aspx...
- Page 45 Product Registration and Customer Support: Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and marketing of hearth products. To provide the best support for your product, we request that you complete a product registration form found on our Web Site under Customer Care within ninety (90) days of purchase.
- Page 48 Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ Regency is a trademark of FPI Fireplace Products International Ltd. Printed in Canada © Copyright 2016, FPI Fireplace Products International Ltd. All rights reserved.