Fujitsu PRIMERGY CX400 M1 System Configurator And Order-Information Manual page 8

B
Rack version for 19'' racks with
No PSU included in Base Unit
Basic unit CX400 M1 for
CX2550 M2 variant 24x 2,5 HDD
Basic unit CX400 M1 for
CX2570 M1 variant
Basic unit CX400 M1 for
CX2550 M2 variant 8x 2,5 HDD
S26113-F617-E50
1,600W PSU module platinum
redundancy
94% efficiency (platinum)
uses hot plug PSU slot
min. 2 / max. 2x per system
Full redundancy cannot be guaranteed for high duty.
config.
In this case SysArch will generate a warning and
PowerSafeguard will throttle CPUs and memory
in case of a PSU failure.
So, power consumption will be limited to 1,600W.
2.400W (S26113-F620-E30) must use Power Cord 16A (S26361-F3151-E301)
for CX400 M1 within rack
please choose only 1 of this 2 cables
S26361-F3151-E351
Power Cord 10A
max.
IEC 320 C19 -> C14
2 x
default within rack
1x per PSU
S26361-F5558-E50
Liquid cooling
tube set
for Liquid cooling
1x per CX400
C
S26361-K1530-V100
S26361-K1530-V200
S26361-K1530-V300
S26361-F3151-E301 S26361-F3151-E500
Power Cord 16A Power Cord
IEC 320 C19 -> C20 IEC320 C19 ->
US NEMA L6-20p
for 100V-115V only*) without rack only
1x per PSU 1x per PSU
Please order appropriate power cord additionally:
Power code IEC320 C19 -> C14 (200-240V only)
Power code IEC320 C19 -> C20
Power code IEC320 C19 -> US NEMA L6-20p
Fujitsu Technology Solutions x86 PRIMERGY Server
System configurator and order-information guide
PRIMERGY CX400 M1
For AC 100V environment using CX2550M1/M2, restrictions
based on the quantity of memory and HDD applied as follow :
Memory (RDIMM) / Internal HDD quantity
CPU (TDP) Memory quantity
HDD quantity
>= 135 W
120 W
105 W, 90 W, 85 W
65 W, 55 W
Remark : LRDIMM is not supported under AC 100V environment
Liquid cooling is not possible
S26113-F620-E30
2,400W PSU module platinum
redundancy
94% efficiency (platinum)
uses hot plug PSU slot
min. 1 / max. 2x per system
T26139-Y3850-E10
No Power Cord
without rack only
1x per PSU
Status 2016-10-31
8 8 16
2 6
- NA -
X - -
X X X
X X X
In case of 1x 2,400W Config
2x below accelerator card
can't be possible on CX2570
M1/M2
Tesla K80
XeonPhi 3120P / 7120P
You must purchase "Dummy PSU",
if you purchased only one PSU.
S26361-F5564-E10
Dummy PSU
1x
min / max 1x
1600W PSU
S26361-F3151-E351 200-240V only
100-120V /
S26361-F3151-E301
200-240V
*) in System architect please
change the default 16A connection
to a 10A connection for all PSU
S26361-F3151-L350
S26361-F3151-L300
S26361-F3151-L500
16
2 6
NA
-
-
X
2400W PSU
Not supported
100-120V /
200-240V
8 of 33